Table of Contents
Advertisement
Local programming requires the use of a 2-line Alpha keypad (e.g., 6139) connected to the keypad terminals on the control.
Field Function
––––––––
––––––––––––––
SYSTEM SETUP ( 20
20
INSTALLER CODE
21
QUICK ARM ENABLE
22
RF SYSTEM TYPE
23
FORCED BYPASS FUNCTION
24
RF HOUSE ID CODE
25
OUTPUT RELAY MODULE
26
VOICE MODULE ACCESS CODE
OUTPUT TO LONG RANGE RADIO †
27
ZONE SOUNDS AND TIMING ( 28 –
SINGLE ALARM SOUNDING/ZONE †
28
29
FIRE SOUNDER TIMEOUT
30
ALARM BELL TIMEOUT
38
ENTRY DELAY
39
AUDIBLE EXIT WARNING
DIALER PROGRAMMING ( 40 –
40
PABX ACCESS CODE
41
PRIMARY PHONE No.
42
SECONDARY PHONE No.
43
SUBSCRIBER ACCT No.
45
PHONE SYSTEM SELECT
†
Entry of a number other than one specified will give unpredictable results.
www.PDF-Zoo.com
VISTA-10
PROGRAMMING FORM
SE
To set all program fields to Ademco default values: Key
Programmed Values
––––––––––––––––––––––––––––––––
27)
Enter 4 digits, 0-9.
†
[0]
0 = no; 1 = yes
[0]
0 = none; 1 = 5700 System (4281 type rcvr); 2 = 5800 System (5881/ 5882 type rcvr).
†
[0]
0 = none; 1 = bypass open zones.
MUST enter (01-31) for 5700 System. Enter also for 5827/5827BD Keypad if used in 5800
system.
†
[0]
0 = none; 3 = 4204.
1st digit: Enter 1–9; 2nd digit: Enter only #+11 for '
0 in either position = disabled.
[0]
0 = no; 1 = yes. If yes selected, dialer reports to PRIMARY No. (field
sent via LRR. All dialer and LRR reports will be in Contact ID format (overriding field
selection).
39)
[0]
0 = no; 1 = yes.
†
[0]
0 = fire sounder timeout; 1 = no fire sounder timeout.
†
[1]
0 = none; 1= 4 min; 2 = 8 min; 3 = 12 min; 4 = 16 min.
†
[2]
0 = 0 sec ; 1= 20 sec; [2 = 30 sec]; 3 = 45 sec; 4 = 60 sec; 5 = 90 sec
EXIT Delay = ENTRY Delay + 15 sec.
†
[1]
0 = no; 1 = yes.
50) Note: In fields 40, 41, & 42: Enter 0–9, # +11 for , # +12 for #, # +13 for a pause.
Enter up to 4 digits if PABX code is needed to access an outside line. If fewer than 4 digits
entered, do not fill unused spaces–exit by pressing
To clear entries from field, press
Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing
if entering next field). To clear entries from field, press 41 .
Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing
entering next field). To clear entries from field, press
Enter 0-9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; [#+15 for F]. Enter
fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as
the first digit of a 4-digit account number for Nos. 0000–0999. End field by pressing
(and press next field).
Examples: For Acct No. 1234 , enter:
†
[0]
If Cent. Station IS NOT on a WATS line: 0 = Pulse Dial; 1 = Tone Dial
If Cent. Station IS on a WATS line: 2 = Pulse Dial ; 3 = Tone Dial
firealarmresources.com
[
] = Default Value
[4] [1] [1] [1]
[0][0]
[0][0]
40 .
For Acct No. B234, enter:
#+11
For Acct No. 123, enter:
– 3 –
97.
, #+12 for '#'.
'
47) will also be
(and press 41, if entering next field).
(and press 42,
(and press 43 if
42 .
1
2
3
4
2
3
4
1
2
3
46
as the
Advertisement
Table of Contents
