Table of Contents
Advertisement
USER GUIDE
QUICK START GUIDE
Anti-Tip Bracket
Use one of the methods below to secure the unit
Anti-Tip Bracket
Anti-Tip Bracket
CABINET/COUNTER ANTI-TIP INSTALLATION
(For built-in applications)
Use one of the methods below to secure the unit
UNITS WITH FRONT-MOUNTED DOOR HINGES
CABINET/COUNTER ANTI-TIP INSTALLATION
1.
Slide unit out so screws on front of unit are easily
(For built-in applications)
accessible.
1.
Slide unit out so screws on front of unit are easily
2.
Remove the two screws from the front of the unit.
accessible.
2.
Remove the two screws from the front of the unit.
3.
Bend bracket along one of the perforations to allow
attachment to the desired adjoining surface.
3.
Bend bracket along one of the perforations to allow
4.
Gently push unit into position. Be careful not to
attachment to the desired adjoining surface.
entangle the electrical cord or water line, if applicable.
4.
Gently push unit into position. Be careful not to
5.
Check to be sure the unit is level from front to back
entangle the electrical cord or water line, if applicable.
and side to side. Make any necessary adjustments.
The unit's top surface should be approximately 1⁄8"
5.
Check to be sure the unit is level from front to back
(3 mm) below the countertop.
and side to side. Make any necessary adjustments.
The unit's top surface should be approximately 1⁄8"
6.
Secure bracket to adjoining surface.
(3 mm) below the countertop.
FLOOR MOUNTED ANTI-TIP INSTALLATION
6.
Secure bracket to adjoining surface.
(For free-standing applications)
1.
Locate two anti-tip brackets included with the kit.
FLOOR MOUNTED ANTI-TIP INSTALLATION
(For free-standing applications)
2.
Place the unit into the area where it will be installed.
1.
Locate two anti-tip brackets included with the kit.
Check the door, sides, and top for a proper fit. Also
test to make sure the door opens and closes freely.
2.
Place the unit into the area where it will be installed.
Check the door, sides, and top for a proper fit. Also
3.
Remove grille and place a mark on the floor at the
test to make sure the door opens and closes freely.
front of the unit. Also place a mark on the floor in the
center of the unit.
3.
Remove grille and place a mark on the floor at the
front of the unit. Also place a mark on the floor in the
4.
Remove the unit. Using a square, extend center line
center of the unit.
"B" (see chart below). This line serves as the back
edge for the anti-tip brackets. From the center line,
4.
Remove the unit. Using a square, extend center line
measure "A" to the left and right. This line is the outer
"B" (see chart below). This line serves as the back
edge of each bracket.
edge for the anti-tip brackets. From the center line,
measure "A" to the left and right. This line is the outer
Anti-Tip Bracket
edge of each bracket.
Anti-Tip Bracket
Surrounding
area (Top view)
Surrounding
area (Top view)
C L
515
C L
A
7 5⁄8"
B
22"
515
A
7 5⁄8"
5.
Place the anti-tip brackets on the floor against the line
B
22"
drawn for the outer edge. Mark spots for the screw
holes.
5.
Place the anti-tip brackets on the floor against the line
Surrounding
area (Top view)
drawn for the outer edge. Mark spots for the screw
holes.
Surrounding
area (Top view)
Front
of
unit
C
L
Front
of
unit
C
L
6.
Use a 1/8" drill to make two starter holes and fasten
the anti-tip brackets to the floor using the screws
provided.
6.
Use a 1/8" drill to make two starter holes and fasten
7.
the anti-tip brackets to the floor using the screws
Place the unit back into position, making sure the
provided.
feet engage the anti-tip brackets properly. Check
the alignment of the lines made on the floor in step
7.
Place the unit back into position, making sure the
3 with the position of the front feet to ensure proper
feet engage the anti-tip brackets properly. Check
positioning.
the alignment of the lines made on the floor in step
3 with the position of the front feet to ensure proper
positioning.
19
u-line.com
u-line.com
u-line.com
Back of unit
Back wall
Back of unit
Back wall
Front of unit
518
524
9"
11 15⁄16"
Front of unit
22"
22"
518
524
9"
11 15⁄16"
22"
22"
Drill holes and
mount anti-tip
brackets to floor
Back wall
Drill holes and
mount anti-tip
brackets to floor
Back wall
Back
of
unit
Back
of
unit
Advertisement
Table of Contents
