Table of Contents
Advertisement
starting at the corners.
QUICK START GUIDE
4. Rotate door 180° to reverse.
Install top hinge and door:
Install top hinge and door:
1. Use alternate hinge supplied with unit and reinstall the
1.
Install hinge with longer straight edge aligned to
screws. Do not tighten.
outside edge of cabinet. Do not tighten.
2. Rotate the door 180
0
and lift the door on to the
bottom hinge.
3. Align flat edge of the top hinge with the outer edge of
the unit.
USER GUIDE
4. Tighten three screws.
Align and adjust the door:
Align and adjust the door (see DOOR ALIGNMENT AND
Door Adjustments
2.
Rotate door 180
o
ADJUSTMENT).
Install grille:
USER GUIDE
3.
Align edge of the hinge with the outer edge of the
unit.
DOOR ALIGNMENT AND ADJUSTMENT
Install the grille.
Align and adjust the door if it is not level or not sealing
4.
Tighten three hinge screws using a Torx T-25
Door Adjustments
properly. If the door is not sealed, the unit may not cool
screwdriver.
properly, or excessive frost or condensation may form in
5 CLASS REFRIGERATOR & NUGGET ICE MACHINE
5.
Replace hinge cover.
the interior.
DOOR ALIGNMENT AND ADJUSTMENT
NOTICE
Align and adjust the door:
Properly aligned, the door's gasket should be
Align and adjust the door (see DOOR ALIGNMENT AND
Align and adjust the door if it is not level or not sealing
firmly in contact with the cabinet all the way
ADJUSTMENT)
properly. If the door is not sealed, the unit may not cool
around the door (no gaps). Carefully examine
Install grille and hinge cover
properly, or excessive frost or condensation may form in
the door's gasket to ensure that it is firmly in
the interior.
contact with the cabinet. Also make sure the
NOTICE
door gasket is not pinched on the hinge side of
Properly aligned, the door's gasket should be
the door.
firmly in contact with the cabinet all the way
around the door (no gaps). Carefully examine
CAUTION
!
the door's gasket to ensure that it is firmly in
Do not attempt to use the door to raise or pivot
contact with the cabinet. Also make sure the
your unit. This would put excessive stress on
door gasket is not pinched on the hinge side of
the hinge system.
the door.
Alignment and Adjustment Procedure
CAUTION
!
1.
Open door and remove gasket near the hinges.
Do not attempt to use the door to raise or pivot
2.
Using a T-25 Torx bit, loosen each pair of Torx head
your unit. This would put excessive stress on
screws both the upper and lower hinge plates.
the hinge system.
3.
Square and align door as necessary.
Alignment and Adjustment Procedure
4.
Tighten Torx head screws on hinge.
1.
Open door and remove gasket near the hinges.
5.
Reinstall gasket into the channel starting at the corner.
2.
Using a T-25 Torx bit, loosen each pair of Torx head
screws both the upper and lower hinge plates.
and set on bottom hinge.
Door Adjustments 2
CAUTION
!
Do not attempt to use the door to raise or pivot
your unit. This would put excessive stress on
u-line.com
u-line.com
the hinge system.
Alignment and Adjustment Procedure
1.
Open door and remove gasket near the hinges.
2.
Using a T-25 Torx bit, loosen each pair of Torx head
screws both the upper and lower hinge plates.
3.
Square and align door as necessary.
4.
Tighten Torx head screws on hinge.
5.
Reinstall gasket into the channel starting at the corner.
REVERSING THE DOOR
1.
Open door.
2.
Using T-25 Torx bit loosen screw #1 and remove screw
#2 on top and bottom hinge. Slide and remove the
door from the unit.
REVERSING THE DOOR
1.
Open door.
Door Adjustments
2.
Using T-25 Torx bit loosen screw #1 and remove screw
#2 on top and bottom hinge. Slide and remove the
door from the unit.
Note: One hinge includes a metal spacer. Spacer
must be used with that hinge when reversing the
door.
3.
Remove caps from screw heads on opposite side (2 on
top and 2 on bottom). Using #2 Phillips bit, remove
the 4 underlying screws. Reinstall the screws and caps
Note: One hinge includes a metal spacer. Spacer
on the opposite side.
must be used with that hinge when reversing the
door.
4.
Partially install screw #1 in the outer most holes on
top and bottom. Rotate door 180o, align hinge over
3.
Remove caps from screw heads on opposite side (2 on
screw #1 and slide/seat into position. Reinstall screw
top and 2 on bottom). Using #2 Phillips bit, remove
#2 on top and bottom. Tighten both screws and install
the 4 underlying screws. Reinstall the screws and caps
hinge cover.
on the opposite side.
Align and adjust the door:
4.
Partially install screw #1 in the outer most holes on
Align and adjust the door (see DOOR ALIGNMENT
top and bottom. Rotate door 180o, align hinge over
AND ADJUSTMENT).
screw #1 and slide/seat into position. Reinstall screw
#2 on top and bottom. Tighten both screws and install
15
hinge cover.
Align and adjust the door:
T-25 Torx Screw
T-25 Torx Screw
2
1
2
1
u-line.com
4
A
A
A
u-line.com
u-line.com
Advertisement
Table of Contents
