Whirlpool WFW9620HW0 Use And Care Manual page 18

WASHER CARE (cont.)
2. Chlorine Bleach Procedure:
a. Open the washer door and remove any clothing
or items.
b. Open the single-load dispenser drawer and add
regular liquid chlorine bleach to the MAX level in
both the bleach compartment and the fabric softener
compartment. Either traditional or HE chlorine bleach
can be used.
IMPORTANT: Do not use thickened, easy-pour,
or no-splash bleach as excess suds may occur.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c. Close the washer door and the dispenser drawer.
d. Do not add any detergent or other chemicals to the
washer when following this procedure.
e. Select the Clean Washer with affresh
f. Select the FanFresh
interior after the cycle is complete.
NOTE: The washer remembers your last option
selection and will use it for future wash cycles until
you deselect that option.
g. Touch and hold START/PAUSE to begin the cycle.
The Clean Washer with affresh
is described below.
NOTE: For best results, do not interrupt cycle.
Description of Clean Washer with affresh
Operation:
1. The Clean Washer with affresh
whether clothing or other items are in the washer.
2. If no items are detected in the washer, it will proceed with
the cycle.
a. If any items are detected in the washer, "rL"
(remove load) will be displayed. The door will unlock.
Open washer and remove any garments from the
washer drum.
b. Touch POWER to clear the "rL" code.
c. Touch and hold START/PAUSE to restart the cycle.
3. Steam models only: During the first 20 minutes of the
cycle, it will activate the steamer but the drum will not
spin or fill with water. You may see condensation on the
door window during this initial phase. If you are using
an affresh Washer Cleaner tablet, it will not dissolve
®
completely during the steam phase. This is normal.
After the cycle is complete, leave the door open slightly to
allow for better ventilation and drying of the washer interior.
18
cycle.
®
option to help dry the washer
®
cycle operation
®
Cycle
®
cycle will determine
®
WASHER CARE (cont.)
Cleaning the Dispensers
After using the Clean Washer with affresh
find some residue buildup in the washer's dispensers.
To remove residue from the single-load dispenser, remove
the drawer and wipe the surfaces with an affresh
Cleaning Wipe or a damp cloth and towel dry either before
or after you run the Clean Washer with affresh
an all-purpose surface cleaner, if needed.
To remove residue from the Load & Go™ dispenser, lift the
handle on the dispenser housing and pull to remove it from
the washer cabinet; then rinse the dispenser thoroughly with
running water. Wipe the outside dispenser surface with an
affresh Machine Cleaning Wipe or a damp cloth, and towel
®
dry. Use an all-purpose surface cleaner, if needed.
Replace the dispenser in the washer cabinet and make sure
that it is correctly seated.
IMPORTANT: Dispensers are not dishwasher safe.
Cleaning the Outside of the Washer
Use an affresh Machine Cleaning Wipe or a soft, damp
®
cloth or sponge to wipe up any spills. Occasionally wipe the
outside of your washer to help keep it looking new. Use an
affresh Machine Cleaning Wipe or mild soap and water.
®
IMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
CLEAN WASHER CYCLE REMINDER
The Clean Washer with affresh
end of a wash cycle when the washer has run 30 wash
cycles. This is a reminder to run the Clean Washer with
affresh cycle.
®
If the Clean Washer with affresh
message will stop flashing at the end of a wash cycle
after running three more regular wash cycles. After 30 more
wash cycles are completed, the Clean Washer with affresh
message will again flash at the end of a wash cycle as a
reminder.
cycle, you may
®
Machine
®
cycle. Use
®
message will flash at the
®
cycle is not run, the
®
®