Related Manuals for LG LW300C-CA
Summary of Contents for LG LW300C-CA
- Page 1 INSTALLATION MANUAL LED TV Please read this manual carefully before operating your set and retain it for future reference. LW300C-CA LW340C-CA LW340C-DA LW540S-DA LW310C-CA LW340H-CA www.lg.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INSTALLATION MENU Introduction LG Hotel Mode Setup TV Manager - 1. USB - 2. Diagnostics Password Change Set ID Setup Configuration Setup Time Scheduler Lock Mode External Speaker HCEC Setup Insert Image Welcome Video Pro:Centric SuperSign Server Setup... -
Page 3: Installation Menu
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’. The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators. -
Page 4: Lg Hotel Mode Setup
Previous S/W : 02.00.00.01 Micom : 0.00.84 Use the button to select the LG Hotel Mode Setup. Use the OK button and then button to select Hotel Mode Operation. *When 'Hotel Mode Operation' is set to Yes(Work), all functions of Hotel Mode apply. - Page 5 Operation’ and ‘Local Key Operation’ will be worked by below. (4-1) IR Operation Decide whether work the LG remote control or not. y Able to set Normal, Use PWR Only, Block All y When ‘IR Operation’ is set to Block All, all normal remote keys don’t work. Use PWR Only (Block except power) makes block all remote keys except power key.
- Page 6 (4-2) Local Key Operation Decide to operate 'Local/Front Key' working behavior by setting ‘Local Key Operation’ as Normal, Use PWR Only, Block All. y When 'Local Key Operation' is set to Block All, all local keys don’t work. If value is Use PWR Only, it blocks all local keys except power key.
- Page 7 Programme Change (5-3) Decide to change channel or not by setting ‘Program Change' as ‘Yes’(Change Possible) or ‘No’(Change Impossible) when present source is TV. y When ‘Programme Change' is set to No (Change Impossible) » Program Key, Numeral Key, List Key, Q.View Key don't work and entering 'Channel Menu' in the Main Menu OSD is impossible.
- Page 8 (6) Power Management The Power Management feature will turn off the television receiver if no input control command is received from either the Local or IR Key within a selected hours. y Activity on either of these inputs shall restart the ‘Power Management’ timer and check key time interval again.
-
Page 9: Aspect Ratio
(8-3) A/V Setting If ‘A/V Setting’ is changed from ‘No’ to ‘Yes’, parameters that are set before entering ‘Installation Menu’ are applied whenever turn on power. y Following Parameters are applied to basic. » Picture section - PSM mode, Picture Data (Contrast, Brightness, Color, Sharpness, Tint) »... - Page 10 (11) Radio Video Blank (Except for 43/49/55LW340C-DA) Manage video blank channel(sound only). This feature affects on analog channel (ATV) only. (11-1) Start PR. No. y Start channel number to video blank. y Available programme to set are 0~199(For Taiwan : TV 2~69, CATV 1~199). (11-2) No.
-
Page 11: Volume
Public Display Settings / LG Hotel Mode Setup (Value Range Table) Item Enable Disable Initial Hotel Mode Operation Power On Status *STD Volume Start Volume Off, Minimum Volume ~ Maximum Volume Maximum Volume Minimum Volume ~ 100 Minimum Volume 0 ~ Maximum Volume... -
Page 12: Tv Manager
Plug USB memory card into the USB port of the TV. button to select the TV Manager option and then press the OK button. Use the Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change Set ID Setup... - Page 13 Select the EPK option (software update) and then use the green and yellow buttons to download either SPI Boot or LG Boot Logo. If you checked the LG Boot Logo checkbox, then the Splash image, if selected, will be unchecked. Also, if you select the LG Boot Logo and proceed with the download, the existing Splash image will be deleted.
- Page 14 USB Cloning An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the same Master TV Setup: Public Display Mode Installation Menu settings, User A/V settings and the Channel Map. This newer procedure significantly decreases the installation time that would be necessary if the standard RS-232C method were used instead.
- Page 15 Plug USB memory card into the USB port of the TV. Use the button to select the TV Manager option and then press the OK button. Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change Set ID Setup...
- Page 16 Plug USB memory card into the USB port of the TV. Use the button to select the TV Manager option and then press the OK button. Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change Set ID Setup...
- Page 17 CABLE IN Use the button to select the TV Manager option and then press the OK button. RS-232C IN Installation Menu (V 3.0) (CONTROL & SERVICE) LG Hotel Mode Setup TV Manager Password Change Set ID Setup Configuration Setup Time Scheduler...
-
Page 18: Diagnostics
It checks and records good and bad channel signals, and then provides the signal information to a USB storage device in XML file format. Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager TV Manager... - Page 19 y Go to Installation menu -> TV Manager -> Diagnostics -> Diagnostics Setup y Set the level value in Signal Tracer Set. (Disable, 10 to 90) TV Manager Diagnostics Setup Diagnostics Setup Signal Tracer Set Disable Diagnostics ► ◄ Previous Previous y Change the channel and tune to a digital channel, then maintain the status for more than 5 seconds.
-
Page 20: Password Change
- To ensure more security, Password can be changed by installers’ own design. - The changed password is applied to the ‘extra contents’ password.( *Only for LW340H-CA series) Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change... -
Page 21: Set Id Setup
Set ID Setup Installation Menu (V 3.0) LG Hotel Mode Setup Set ID Setup TV Manager Password Change Set ID Lock ◄ ► Set ID Setup Set ID Setup Set ID Configuration Setup Previous Time Scheduler Lock Mode External Speaker... -
Page 22: Configuration Setup
Configuration Setup y Image shown may differ from your TV. Installation Menu (V 3.0) Configuration Setup LG Hotel Mode Setup Number of RCU TV Manager Splash Offset Time Password Change ◄ ► USB Auto Playback Set ID Setup Photo 15Min Auto Off... - Page 23 For the audio signal, the priority order is the RGB -> AV -> Audio In component ports. (7) Screen Saver Cube y When ‘Screen Saver Cube’ is set to ‘No’, TV will do not display LG Screen Cube. (8) One Channel Map y If 'One Channel Map' is 'YES', the TV will operate as below.
-
Page 24: Time Scheduler
Time Scheduler Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change Time Scheduler Set ID Setup Time Scheduler Configuration Setup ◄ ► On Timer Time cseduler Time Scheduler Lock Mode Off Timer External Speaker Previous HCEC Setup Welcome Video S/W : 02.00.00.01 Micom : 0.00.84... -
Page 25: Lock Mode
Lock Mode Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change Lock Mode Set ID Setup Enable Data Service Configuration Setup ◄ ► Enable Time Scheduler Enable Lock Mode Factory Reset External Speaker Previous HCEC Setup Welcome Video S/W : 02.00.00.01 Micom : 0.00.84... -
Page 26: External Speaker
External Speaker (*Except for LW340C series) Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change External Speaker Set ID Setup Fixed ◄ ► Volume Control Configuration Setup 1 Watt Output Time Scheduler Lock Mode Previous External Speaker... - Page 27 Speaker output SETUP Connect the external speaker to the external speaker out jack on the TV. EXTERNAL SPEAKER OUT RIGHT LEFT NOTE y External speaker must be used three plug(SE : Single Ended, Stereo) as shown in the drawings and external speaker fully inserted with external Speaker Jack.
-
Page 28: Hcec Setup
HCEC Setup Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change HCEC Setup Set ID Setup CEC Mode Default ◄ ► Configuration Setup IR Decoding Time Scheduler Device ID Lock Mode StandBy External Speaker HTNG HotelMode HCEC Setup... - Page 29 (c) Stand By y Sets the sending and receiving scenario of the operation about [CEC Op standBy(0x0c) Command(Device Power)]. y The detailed scenario is described on the table below. Send Receive Send Only Receive Only (2) HTNG HotelMode y If the following options are selected because of the HTNG command: *Power On Default, Start Volume, Maximum Volume, Minimum Volume, or Start Volume, then the value for the HTNG HotelMode changes automatically to Yes and, even if the HotelMode is set to No, the above options are still affected.
-
Page 30: Insert Image
INSERT IMAGE y This feature allows you to display an image you have stored on the TV instead of the LG Cube when there is no signal due to DTV signal attenuation, external device failure, or cable removal. Installation Menu (V 3.0) -
Page 31: Welcome Video
WELCOME VIDEO Installation Menu (V 3.0) LG Hotel Mode Setup TV Manager Password Change Welcome Video Set ID Setup Configuration Setup Welcome Video ◄ ► Time Scheduler Video Reset Confirm Lock Mode Previous External Speaker HCEC Setup Welcome Video S/W : 02.00.00.01 Micom : 0.00.84 y This feature allows you to download videos via USB storage to display on your TV after your TV boots up and the boot logo appears. -
Page 32: Pro:centric
PRO:CENTRIC Installation Menu (V 3.0) LG Hotel Mode Setup TV manager Password Change Set ID Setup Pro:Centric Configuration Setup Mode ► ◄ Time Scheduler Lock Mode Previous External Speaker HCEC Setup Welcome Video Pro:Centric S/W : 02.00.00.01 Micom : 0.00.84 Use the button to select the Pro:Centric. -
Page 33: Supersign Server Setup
SUPERSIGN SERVER SETUP (* Only for LW540S series) Installation Menu (V 3.0) Public Display Settings TV Manager SuperSign Server Setup Password Change Play Name Press OK Set ID Setup Server IP Setting Press OK Configuration Setup Server IP Status Time Scheduler Not connected Lock Mode Previous... -
Page 34: Ntp Time Sync
(* Only for LW540S series) y This feature allows you to receive time information via NTP(Network Time Protocol) Time Server to set current clock. Installation Menu (V 3.0) LG Hotel Mode Setup TV manager Password Change NTP Timer Sync Set ID Setup... -
Page 35: Download Extra Contents
DOWNLOAD EXTRA CONTENTS (*Only for LW340H-CA series) 1. Download Extra Contents(flash file) to TV set y The Pro:Centric application can be downloaded to your TV. FLASH (*.SWF) / GEM supporting file An SWF file complied with Flash Lite 3.0 or earlier (the 3.0 version is recommended) y Mode must be set to Flash or GEM under Pro:Centric in Installation Menu. - Page 36 MY MEDIA Movie List Photo List Music List Extra Contents Press OK( ) to see extra contents. Option Exit Select Extra Contents. Enter a four digit password. y The TV is set with the initial password “1-1-0-5”. NOTE y You can not select the Extra Contents in MY MEDIA when the Mode under Pro:Centric in Installation Menu is set to OFF.
- Page 37 You can see a new Application File on TV. Introduction y Change Mode other than Flash or GEM under Pro:Centric in Installation Menu. y When you change the Mode, the downloaded content is deleted from the memory. NOTE y When playing the Application file(FLASH or GEM file), the buttons are controlled according to the settings of the Extra Contents option.
-
Page 38: Digital Signage Media Player
DIGITAL SIGNAGE MEDIA PLAYER Digital Signage Media Player Overview (* Only for LW540S series) The Digital Signage Media Player can play content produced and distributed by SuperSign Elite-W. Supported content types consist of photographs, videos, external inputs such as TV broadcasts, texts, and music. -
Page 39: External Control Device Setup
EXTERNAL CONTROL DEVICE SETUP KEY CODES • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) CH +, PR + R/C Button List R/C Button CH -, PR - R/C Button Exit R/C Button Volume + R/C Button PIP(AD) -
Page 40: External Control Device Setup
(TV) (PC) • LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter RS-232C IN which is not made nor provided by LG. (CONTROL & SERVICE) (PC) (TV) • It can be purchased from computer stores that carry accessories for IT support professionals. - Page 41 (TV) (PC) (TV) (PC) Phone jack Type RS-232C IN • You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and (CONTROL & SERVICE) (PC) (TV) the TV, which is specified in the manual. RS-232C IN (CONTROL &...
- Page 42 Communication Parameters • Baud rate : 9600 bps (UART) • Stop bit : 1 bit • Data length : 8 bits • Communication code : ASCII code • Parity : None • Use a crossed (reverse) cable. Command reference list (Depending on model) DATA DATA...
- Page 43 Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99.
-
Page 44: Volume Control
* Commands may work differently depending on model and signal. 01. Power (Command: k a) 04. Volume Mute (Command: k e) ► To control Power *On or Off of the set. ► To control volume mute on/off. You can also adjust mute using the MUTE button on Transmission[k][a][ ][Set ID][ ][Data][Cr] remote control. -
Page 45: Color
10. Sharpness (Command: k k) 16. Color(Colour) Temperature (Command: x u) ► To adjust the screen sharpness. ► To adjust colour temperature. You can also adjust You can also adjust sharpness in the PICTURE menu. Color(Colour) Temperature in the PICTURE menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Transmission [x][u][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 32... - Page 46 20. Tune Command (Command: m a) Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel * This command may work differently depending on model number, the Major is the number that the channel should and signal.
- Page 47 * Set the saved channel status to del(ATSC, ISDB)/ Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] skip(DVB) or add. [Data 02][Data 03][Data 04][Data 05] [x][a][ ][Set ID][ ][NG][Data 00][x] 22. Key (Command: m c) • For Japan Model ► To tune channel to following physical/major/minor ►...
- Page 48 24. Input select (Command: x b) (Main Picture Input) ► To select input source for main picture. X : don’t care Transmission [x][b][ ][Set ID][ ][Data][Cr] Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] Data 00 : DTV 01 : CADTV [Data03][x] 02 : Satellite DTV 10 : ATV [t][ ][Set ID][ ][NG][Data00][x] ISDB-BS (Japan)
- Page 49 27. Auto Configure (Command: j u) (Depending on model) ► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01 : To set Ack [u][ ][Set ID][ ][OK/NG][Data][x]...