Table of Contents
Advertisement
1 – Introduction
6 – After recording
This section deals with the actions taken after record-ing:
finalizing for CD-R and CD-RW discs, and erase opera-
tions for CD-RW discs.
Once finalized, CD-R discs are truly final—no more can
be recorded on them. By contrast, CD-RW discs can be
"unfinalized" using the CC-222SL
Finalizing
As has been explained earlier (see "Finalizing" on page 9),
in order for a disc to become a standard CD, it must have
a Table of Contents (TOC) written to it. This process is
known as finalizing.
An unfinalized disc can always be distinguished on the
CC-222SL
II by the NO TOC indicator under the disc
MK
type on the display being lit when the disc is inserted.
CAUTION
Do not turn the power off during this operation. Not
only you may lose the recorded data, but also the disc
may be damaged and become un-usable.
To finalize a disc:
1 With the unfinalized (recordable) disc loaded, and
the unit in stop mode, press the
The display shows
F i na l i ze OK ?
Unfinalizing CD-RW discs
If a CD-RW disc has been finalized, it is possible to erase
the Table of Contents in the following way:
1 With the finalized disc loaded and the unit in stop
mode, press the
ERASE
2 If the display does not show the word
, turn the
MULTI DIAL
i ze ?
until it is displayed.
3 To start the unfinalizing process, press the
control or press the
DIAL
If you do not want to proceed with the unfinalizing
process, press the
ERASE
Erasing
Unfinalizing (described above) is a special case of eras-
ing a disc. It is also possible to erase a track or tracks,
starting with the last-recorded track, a whole disc, or to
"refresh" a disc.
NOTE
Erase procedures are possible only on a CD-RW disc.
Even if a CD-RW disc has been finalized, selecting an
erase procedure will automatically unfinalize it prior
to erasure. The disc may then have to be re-finalized.
Remember that it is not possible to perform any erase
procedures on a CD-R disc.
28
TASCAM CC-222SL
MK
II, that is, their TOC
MK
FINALIZE
key.
.
key.
Unf i na l -
or use the
SKIP
keys
MULTI
key.
ENTER
key or
STOP
key.
II
6 – After recording
can be deleted, and if there is space, further material can
be recorded on them. Even if the disc is full, tracks can be
erased following the unfinalize process, and new material
can be recorded.
2 To start the finalizing process, press the
DIAL
or press the
ENTER
proceed with the finalizing process, press the
NALIZE
key or
STOP
key.
If finalization has been chosen, the display changes.
The
NO TOc
indicator goes out, and the word
the
Rec
indicator flash in the display. The unit starts
counting down from a time shown on the display.
After finalization,
cD-RW
and
,
changes to
cD-RW
cD-R
NO TOc
NOTE
Although CD-R discs finalized on the CC-222SL
may be replayed on ordinary CD players, remember
that finalized CD-RW discs may not play on CD play-
ers.
If unfinalization has been chosen, the
starts flashing in the display, and the word
also starts flashing. The unit starts counting down
from a time shown on the display.
After unfinalization,
cD-RW
RW
,
NO TOc
indicator.
MULTI
key. If you do not want to
FI-
and
TOC
,
indicator changes to
NO TOc
indicator.
cD-R
II
MK
indicator
NO TOc
ERASE
indicator changes to
cD-
Advertisement
Table of Contents
