Table of Contents
Advertisement
Unpacking and Installation
What's in the Box?
To avoid damage to the unit during transportation, the
Entrypoint is delivered in a special shipping box, which should
contain the following components:
•
Entrypoint Server
•
Network cables
•
ISDN cables (5m) (Qty 4) – only if the 3G/Audio GW 4xBRI
option is chosen
•
ISDN cables (5m) (Qty 1) – only if the 3G/Audio GW 1xPRI
option is chosen
•
Ethernet cable (5m).
•
Power Cables
•
Install Sheet
•
User Manual CD
•
Registration Card
•
Accessories bag (Console cable, rack ears, rubber feet)
Please report any discrepancies to your TANDBERG
representative immediately.
A brief, yet detailed presentation of the procedure to get
you up and going can be found in the Installation Sheet
accompanying your TANDBERG product.
RS 232
cable. To control
the Entrypoint using the
data port, connect an
RS 232 cable between
the Entrypoint's RS 232
connector and the
COM-port on a PC. See
Entrypoint Configuration
and the
Data Port
Command Interface User
Guide
(available separately)
for more on this.
Table of
Trademarks &
Patents &
Contents
Copyright
Disclaimers
D 14050.04
10.2007
Installation Site Preparations
•
Make sure that the Entrypoint is accessible and that all
cables can be easily connected.
•
For ventilation: Leave a space of at least 10cm (4 inches)
behind the Entrypoint's rear panel and 10cm (4 inches) in
front of the front panel.
•
The room in which you install the Entrypoint should have
an ambient temperature between 0ºC and 35ºC (32ºF and
95ºF) and between 10% and 90% non-condensing relative
humidity.
•
Do not place heavy objects directly on top of the Entrypoint.
•
Do not place hot objects directly on top, or directly beneath
the Entrypoint.
•
Use a grounded AC power outlet for the Entrypoint.
•
You will need a CSU (Channel Service Unit) between your
system and the PRI line from your network provider.
•
Make sure that it is possible to receive and to make mobile
(H.324M) video calls from behind this line. Check this with
your network operator!
•
If you are behind a PABX make sure that the PABX is capable
of routing mobile (H.324M) video calls.
Connecting the Cables
LAN
the Entrypoint on
IP, connect a LAN
cable from the
1
connector on the
Entrypoint to your
network. The
and
not used and should be
left open.
Safety/
To Get You
To Get You
Using the
Environmental
Up and Going
up and Going
Entrypoint
cable. To use
LAN
LAN
2,
3
4
connectors are
ISDN PRI or BRI
connected to a CSU (Channel Service Unit). You will
need a CSU between your Entrypoint and the PRI line
from your network provider.
Viewing the
Configuring
System Status
the Entrypoint
11
General Installation Precautions
•
Never install telephone wiring during a lightning storm.
•
Never install telephone jacks in wet locations unless the
jack is specifically designed for wet locations.
•
Never touch uninstalled telephone wires or terminals unless
the telephone line has been disconnected at the network
interface.
•
Use caution when installing or modifying telephone lines.
•
Avoid using a telephone (other than a cordless type) during
an electrical storm. There may be a remote risk of electrical
shock from lightning.
•
Do not use the telephone to report a gas leak in the vicinity
of the leak.
•
The socket outlet shall be installed near to the equipment
and shall be easily accessible.
•
Never install cables without first switching the power OFF.
•
This product complies with directives: LVD 73/23/EC, EMC
89/366/EEC, R&TTE 99/5/EEC.
•
This product complies with the standards GR-63-CORE and
GR-1089-CORE and is NEBS approved by UL. For NEBS
compliance, there should be a clearance of 9.1 cm between
the product and any other product mounted in the rack.
Power
the system power
cable to an electrical
distribution socket.
cables. The E1/T1 cable should be
Maintenance
Dial Plan
Services
& Upgrade
Examples
TANDBERG
ENTRYPOINT
USER GUIDE
cable. Connect
Contact
Information
Advertisement
Table of Contents
