Table of Contents
Advertisement
Quick Links
BEFORE YOU BEGIN
HOW TO USE THESE INSTRUCTIONS
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and
installation sequences. Follow the sections that pertain
to your particular installation. This will help you avoid
costly mistakes. In addition to proper installation, read
all operating and safety instructions.
NOTES
S
Observe all local plumbing and building codes.
S
Shut off the water supply.
S
Ensure that the new toilet has the correct
roughing-in dimension of 12". See Fig. #3.
S
Be very careful while working with vitreous china
products. Vitreous china can break or chip if the
bolts and nuts are overtightened, or if carelessly
handled.
S
Carefully inspect the new fixture for any sign of
damage.
TOOLS AND MATERIALS REQUIRED
S
10" adjustable wrench
S
12" pipe wrench
S
Metal file (file cut)
S
Tape measure
S
Tubing cutter
S
Level
S
Hacksaw
AC
116627-2-
R
1 1
VITREOUS CHINA
REVERSE TRAP TOILET
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler Co. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information – please leave instructions
for the consumer.
S
Fixture dimensions are nominal and conform to
tolerances established by ANSI Standards
(A112.19.2).
S
For new construction, refer to the dimensions in
Fig. #3 for locating the supply shut-off valve.
S
Provide adequate trip lever clearance if shelving
or other structures are to be installed above the
toilet tank.
S
Putty knife
S
Screwdriver
S
Toilet gasket (wax seal)
S
Toilet T-bolts (2), 5/16" diameter
S
Toilet setting compound (optional)
S
Toilet supply shut-off valve, 3/8" recommended
NOTICE: If the existing toilet does not have a supply
shut-off valve below the tank, install one before installing
the new toilet.
REVIVAL
E2000 Kohler Co.
Advertisement
Table of Contents
Related Manuals for Kohler REVIVAL
Summary of Contents for Kohler REVIVAL
- Page 1 Follow the sections that pertain publication. Kohler Co. reserves the right to make to your particular installation. This will help you avoid changes in product characteristics, packaging, or costly mistakes.
-
Page 2: Installation
4-1/8” to the left of the closet 4-1/8” flange centerline. 9” Closet Flange The centerline of the supply shut-off valve outlet should Centerline extend 3-5/8” from the finished wall. Install the supply shut-off valve with the outlet vertical. 12” Fig. #3 Kohler Co., Kohler, WI 116627-2-... - Page 3 Be sure the Washer brass nuts are tight enough to achieve a watertight seal. Brass Nut CAUTION: Risk of personal injury or product damage. Overtightening may cause breakage or Fig. #6 chipping of the vitreous china. Kohler Co., Kohler, WI 116627-2-...
- Page 4 Any attempt to adjust the fittings can damage the product. Such adjustments or any modifications of the product are not considered normal usage, and will void the warranty. Fig. #8 Kohler Co., Kohler, WI 116627-2-...
- Page 5 If the toilet does not flush when the lift rod is raised, remove some of the slack in the flapper chain by Tank relocating the flapper chain S-hook to the top hole in Fig. #11 the lift rod. Kohler Co., Kohler, WI 116627-2-...
-
Page 6: Troubleshooting Chart
B. Soil pipe or vent is obstructed. B. Clear obstruction from soil pipe or vent pipe. 7. Toilet does A. Chain is not connected to lift rod or flush valve. A. Reconnect the chain. activate. Kohler Co., Kohler, WI 116627-2-... -
Page 7: Important Consumer Information
If you live in a hard water area, make certain all the fixture Kohler Company shall not be responsible or liable for any rim holes are kept clean to ensure proper operation. tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite). - Page 8 Kohler Co., Kohler, WI 116627-2-...