Setting The Back Matte [Back Matte] - Panasonic AG-HMX100E Operating Instructions Manual

Use the rotary 1 control to set the internal video output type
to back matte video ([BACK MATTE]) or color bar output
([COLOR BAR]).
If [MEMORY] is selected, an external video input source
can be saved in internal memory and used as internal
video ( page 30).
Setting the Back Matte
[BACK MATTE]
To create back matte video as internal video, use the
[BACK MATTE] submenu of the [INT VIDEO] menu.
Rotary 1 Rotary 2 Rotary 3
BACK COLOR LEVEL
MATTE WHITE
WHITE LEVEL
YELLOW 0-255
CYAN
GREEN SET
MAGENTA BACK M
RED WASH
BLUE
BLACK
CUSTOM1
CUSTOM2
To set the back matte video color
1
To check the back matte video color, press the
A/PROG INT (or B/PROG INT) button to set the
currently displayed bus to the internal video.
2
Use the rotary 2 control to set [COLOR] to one
of the colors shown in the table below.
Setting
[WHITE] (factory default
setting)
[YELLOW]
[CYAN]
[GREEN]
[MAGENTA]
[RED]
[BLUE]
[BLACK]
[CUSTOM1] or
[CUSTOM2]
The P , P , and Y values are shown in the joystick
B R
and rotary Z control settings, and 3D display display
area ( page 20).
3
If [CUSTOM1] or [CUSTOM2] is selected in
Step 2, set [SET] to [BACK M] (back matte)
using the rotary 3 control and set [PATTERN] to
[OFF] using the rotary 4 control.
Rotary 4 Rotary 5
PATTERN GRADE
255 H1 0
OFF 0-255
H1
H2
H3
V1
V2
V3
DIAG1
DIAG2
Color
White
Yellow
Cyan
Green
Magenta
Red
Blue
Black
Grey as the factory
default setting
4
If [CUSTOM1] or [CUSTOM2] is selected in
Step 2, use the joystick and rotary Z control to
set the [P ] and [P
B R
255 and the [Y] value in the range of 16 to 235
for selecting the back matte video color.
If other than [CUSTOM1] and [CUSTOM2] is
selected, set the color level (the Y signal level
for white) using the rotary 3 control.
To set the color gradation for back matte
video
1
To check the back matte video color, press the
A/PROG INT (or B/PROG INT) button to set the
currently displayed bus to the internal video.
2
Use the rotary 2 control to set [COLOR] to one
of the colors shown in the table below.
Setting
[WHITE] (factory default
setting)
[YELLOW]
[CYAN]
[GREEN]
[MAGENTA]
[RED]
[BLUE]
[BLACK]
[CUSTOM1] or
[CUSTOM2]
The P
, P , and Y values are shown in the joystick
B R
and rotary Z control, and 3D display settings display
area ( page 20).
3
Set [PATTERN] (gradation pattern) using the
rotary 4 control.
Setting
[OFF]
[H1]
[H2]
[H3]
[V1]
[V2]
[V3]
[DIAG1]
[DIAG2]
4
If [CUSTOM1] or [CUSTOM2] is selected
in Step 2, set [SET] to [WASH] (wash color
meaning companion color for gradation) using
the rotary 3 control.
] values in the range of 0 to
Color
White
Yellow
Cyan
Green
Magenta
Red
Blue
Black
Grey as the factory
default setting
Gradation pattern
No gradation
Horizontal gradation 1
Horizontal gradation 2
Horizontal gradation 3
Vertical gradation 1
Vertical gradation 2
Vertical gradation 3
Diagonal gradation 1
Diagonal gradation 2
29