5.62k Ω → 562 × 10 → 5621 ............RN1/4PC 5 6 2 1 CONTRAST TABLE PDP-R04G/TLDFR and PDP-R04E/WYVI6 are constructed the same except for the following : Part No. Ref. No. Mark Symbol and Description PDP-R04E PDP-R04G Remarks /WYVI6...
Page 3
Part No. Ref. No. Mark Symbol and Description PDP-R04E PDP-R04G Remarks /WYVI6 /TLDFR P9-64 Shield Plate SF ANG2649 Not used P9-65 PC Shield ANG2578 Not used P9-69 Clamp AEC1884 Not used P9-71 PC Guide AMR3393 Not used P9-75 Eye Catching Label...
Page 4
C8501, C8503, C8528, C8533 (100µF/6.3V) ACH1396 ACH1364 C8507, C8526, C8531 (22µF/16V) ACH1400 ACH1370 C8536 (47µF/16V) ACH1391 ACH1371 C8537 CEHAZL471M16 Not used C8538 (10µF/16V) DCH1165 Not used R8552 RS1/16S0R0J Not used CN8502 PLUG (6P) KM200NA6 Not used U8510 DD CON UNIT AXY1070 Not used PDP-R04G...
Page 14
Therefore, when replacing, be sure to use parts of identical designation. • : The power supply is shown with the marked box. 5/8F 2/13 CN8652 2/13 3/13 3/13 4/13 5/13 6/13, 13/13 5/13 4/13 1/13 12/13 1/13-9/13, 11/13, 12/13 4/13,8/13 5/8F CN8654 6/13 12/13 6/13 6/13 13/13F PDP-R04G...
Page 15
2.3 FRONT (1/2) ASSY 1/2F FRONT ASSY (AWZ6815) ¶ FRONT BLOCK 5/8F CN8653 1/2F PDP-R04G...
Page 16
2.4 AV BOARD ASSY (1/8) 1/8F AV BOARD ASSY (AWZ6818) ¶ TUNER BLOCK 3/8F -5/8F 2/8F -8/8F ANALOG 1/8F PDP-R04G...
Page 32
2.12 AC SW ASSY and POWER SUPPLY UNIT POWER SUPPLY UNIT (AXY1081) LIVE NEUTRAL AC SW ASSY (AWZ6783) LIVE AC IN NEUTRAL AC INLET (AKP1249) PDP-R04G...
4. ADJUSTMENT ITEMS If readjustment is necessary because of adjustment error at shipment, perform adjustments as shown below. ¶ Adjustment Points AV BOARD ASSY Rear side SIDE A SIDE A SIDE B PDP-R04G...
Finishing troubleshooting • Diagnosis points MR MAIN BOARD ASSY AV BOARD ASSY • For check the communication with the microcomputer, refer to the section 6.7 SERVICE FACTORY MODE. • The encircled numbers denote measuring point in the Waveforms for Troubleshooting. PDP-R04G...
Page 43
IC8002. Check around IC8002 and Is a signal output from check the communications IC8002? between IC8002 and the (41) microcomputer. Has the signal arrived at Check the communication TP7425? between IC8002 and TP7425. Check around the jack. PDP-R04G...
Page 44
IC on the found to have a failure in MR MAIN BOARD Assy and communication and the the microcomputer normal? microcomputer. Has the symptom been settled when the MR MAIN The panel is defective. BOARD Assy is replaced? Finishing troubleshooting PDP-R04G...
Page 45
Cancel muting then check Is sound muting set? again. Raise the volume then Is the volume set to 0? check again. Is a signal output from IC8003? Check around IC8003 and (3) (13) check each input signal. Check around the jack. PDP-R04G...
Page 46
Is a signal input to IC8002? Check the communications (62), (64) between IC7502 and Is a signal input to IC8002? Check the communications IC8002. between the jack and IC8002. Check around IC8002 and check the communications between IC8002 and the microcomputer. PDP-R04G...
Page 47
AV BOARD Assy TP9301 and TP9303? and MR MAIN BOARD Assy and between the MR MAIN BOARD Assy and MDR Assy. Has the symptom been settled when the system The panel is defective. cable is replaced? Finishing troubleshooting PDP-R04G...
PIONEER Service Manual. A subscription to, or additional copies Also test with plug reversed of, PIONEER Ser vice Manual may be obtained at a (Using AC adapter Earth nominal charge from PIONEER. plug as required)
Page 54
[ Important symbols for good services ] In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely. When you find the procedures bearing any of the symbols, be sure to fulfill them: 1. Product safety You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.
Page 55
CONTENTS SAFETY INFORMATION ............................. 2 1. SPECIFICATIONS ............................5 2. EXPLODED VIEWS AND PARTS LIST ......................6 2.1 PACKING ..............................6 2.2 EXTERIOR SECTION..........................8 2.3 FRONT SECTION............................ 10 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..................12 3.1 BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ................... 12 3.1.1 SIGNAL ROUTE ..........................
1. SPECIFICATIONS Item Media Receiver, Model: PDP-R04E Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 TV Function Receiving System B/G, D/K, I, L/L’ Tuner VHF/UHF E2–E69ch, F2–F10ch, I21–I69ch, IR A–IR Jch CATV Hyper-band, S1–S41ch Auto Channel Preset 99 ch, Auto Preset, Auto Label, Auto Sort STEREO NICAM/A2 Terminals...
2. EXPLODED VIEWS AND PARTS LIST NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Page 58
PACKING parts List Mark No. Description Part No. Mark No. Description Part No. Protector AHA2305 Operating Instructions ARE1368 Cardboard Spacer AHB1246 (English/French/Spanish) Top Pad AHB1247 Operating Instructions ARC1520 Accessory Box AHC1051 (Italian/Dutch/Swedish/Spanish) Carton E See Contrast table(2) Operating Instructions ARE1375 about HDMI NSP 21 Literature Bag...
2.2 EXTERIOR SECTION 83 76 Refer to "2.3 FRONT PANEL SECTION". PDP-R04E...
Page 60
EXTERIOR SECTION parts List Mark No. Description Part No. Mark No. Description Part No. PCB Holder AEC1097 MR MAIN BOARD Assy AWV2041 AV BOARD Assy AWZ6813 Spacer AEC1256 MDR Assy AWZ6778 Locking Card Spacer AEC1429 SR Assy AWZ6817 Wire Saddle AEC1745 FRONT Assy AWZ6832...
Page 62
AAN1469 Front Panel A E AMB2772 Front Panel B AMB2767 Door Cap L AMR3360 Door Cap R AMR3361 Sealing Sheet E AAL2449 Pioneer Badge VAM1124 Door Cushion AEB1391 Lens for LED AMR3353 Screw APZ30P080FMC Screw BMZ30P060FMC PC Card Door AMR3365...
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1.1 SIGNAL ROUTE MR MAIN AV BOARD ASSY BOARD ASSY U7501 Antenna AXF1119 Input IC8002 IC7501 TDA9818TS TTX_R/G/B_DIG IC7502 V / Y MSP3417G Video1 R_TXT_MAIN IC8904 IC8906 G_TXT_MAIN B_TXT_MAIN SLOW_SW_1 TA1287...
Page 64
Video signal Data signal Audio signal Control signal Composite signal RF signal Component/RGB signal Separate signal Digital Video signal Digital Audio signal IC7001 IC7002 Synchronized signal HV57V6432 HV57V6432 20CT-7 20CT-7 PCA_H IC6107 PCA_V FOMAT 3DY/C Decoder PD0278A PE5362A CN7401 PLASMA DISPLAY AD9883A CK_MAIN IC7004...
3.2 OVERALL WIRING DIAGRAM 1/2 - PC CARD MODULE (AXY1073) FRONT ASSY (AWZ6832) REG ASSY (AWZ6814) 1/8 - AV BOARD ASSY (AWZ6813) SR ASSY LED ASSY (AWZ6817) (AWZ6816) POWER SUPPLY UNIT (AXY1065) PDP-R04E...
Page 72
NOTES: • When ordering service parts, be sure to refer to “EXPLODED VIEWS and PARTS LIST” or “PCB PARTS LIST”. • The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical FAN MOTOR designation.
3.6 MR MAIN BOARD ASSY (4/13) 4/13 MR MAIN BOARD ASSY (AWV2041) ¶ AD MAIN BLOCK H : Ch B (TEXT RGB) L : Ch A (COMPONENT / PC RGB) H : FILTER THROUGH L : FILTER ON 13/13 13/13 13/13 13/13 SELECTOR...
Page 80
2/13, 7/13, 8/13 8/13 8/13, 13/13 2/13, 7/13, 8/13 2/13, 4/13, 7/13, 8/13 1/13-3/13, 5 → 3.3V CONVERTER 5/13-9/13, SYNC. SELECTOR 11/13-13/13 H : FILTER THROUGH L : FILTER ON 2/13, 13/13 8/13 L : COMPONENT / PC RGB 4/13 PDP-R04E...
3.7 MR MAIN BOARD ASSY (5/13) 5/13 MR MAIN BOARD ASSY (AWV2041) ¶ AD SUB BLOCK H : Ch B (TEXT RGB) L : Ch A (COMPONENT / PC RGB) H : FILTER THROUGH L : FILTER ON 13/13 13/13 13/13 13/13 13/13...
Page 82
3/13, 7/13, 9/13 9/13 3/13, 7/13, 9/13 3/13, 5/13, 7/13, 9/13 1/13-4/13, 6/13-9/13, 5 + 3.3V CONVERTER 11/13-13/13 SYNC. SELECTOR H : FILTER THROUGH L : FILTER ON 3/13, 13/13 3/13, 13/13 9/13 L : COMPONENT / PC RGB 5/13 PDP-R04E...
3.32 VOLTAGES MR MAIN BOARD ASSY MDR ASSY AV BOARD ASSY FRONT ASSY CN7402 (AKM1234) CN9302 (VKN1220) CN8653 (AKM1201) CN9502 (AKM1201) Voltage Voltage Name Name Name Name 0.00 V+9V_A 8.96 V+9V_A SP_L 0.00 SP_L V+5V_A 5.00 V+5V_A V+3ACT 3.32 V+3ACT V+3COM 3.35 V+3COM...
Page 129
AV BOARD ASSY MR MAIN BOARD ASSY AV BOARD ASSY MR MAIN BOARD ASSY CN8652 (AKM1201) CN7454 (AKM1201) CN8654 (AKM1201) CN7455 (AKM1201) Voltage Voltage Name Name Name Name DSUB_DET 0.00 DSUB_DET SP_R 0.00 SP_R WE_TXT 0.01 WE_TXT 0.00 0.00 SP_L 0.00 SP_L VD_TXT...
Page 130
REG ASSY MR MAIN BOARD ASSY AV BOARD ASSY SR ASSY CN8651 (KM200NA15) CN7451 (AKM1269) CN8658 (AKM1233) CN9452 (VKN1216) Voltage Voltage Name Name Name Name GND_D 0.00 GND_D V+5V_SR 5.06 V+5V_SR V+3V_DD 3.38 V+3V_DD V+3V_SR 3.40 V+3V_SR V+3V_DD 3.28 V+3V_DD 3.36 GND_D 0.00...
4. PCB CONNECTION DIAGRAM NOTE FOR PCB DIAGRAMS : 1. Part numbers in PCB diagrams match those in the schematic 3. The parts mounted on this PCB include all necessary parts for diagrams. several destinations. 2. A comparison between the main parts of PCB and schematic For further information for respective destinations, be sure to diagrams is shown below.
4.5 FRONT and LED ASSY SIDE A SIDE A FRONT ASSY LED ASSY IC9602 IC9601 CN7202 Q9506 Q9507 Q9508 Q9654 Q9653 Q9652 Q9651 CN8656 (ANP2053-A) CN8653 Q9505 Q9503 Q9502 Q9501 IC9501 IC9502 (ANP2053-A) PDP-R04E...
Page 142
SIDE B SIDE B LED ASSY FRONT ASSY (ANP2053-A) (ANP2053-A) PDP-R04E...
5. PCB PARTS LIST NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. When ordering resistors, first convert resistance values into code form as shown in the following examples.
Page 144
Mark No. Description Part No. Mark No. Description Part No. C6880,C6882,C6884,C6886 CCSRCH101J50 COILS AND FILTERS C6888,C6889,C6892,C6895,C6896 CCSRCH101J50 C6899-C6902,C6905,C6906,C6915 CCSRCH101J50 F6401,F6601 EMI FILTER ATF1194 C6917,C6919 CCSRCH101J50 CAPACITORS > C6927,C6928 CCSRCH221J50 C6445,C6644 CCSRCH221J50 C6913 CKSRYF103Z50 C6438,C6638 CKSRYB103K50 C6920 CKSRYF473Z50 C6404,C6424,C6604,C6624 CKSRYB104K16 C6831,C6848,C6881,C6883,C6885 CKSSYF104Z16 C6408,C6411,C6412,C6431 CKSRYB105K10...
Page 145
Mark No. Description Part No. Mark No. Description Part No. RESISTORS IC7456 PQ015YZ01ZP IC7454 PQ050DZ01ZPH R7013-R7018 RAB4CQ220J IC7453 PQ3DZ13 Other Resistors RS1/16SS###J IC7401 SII170BCLG64 IC7404 TC74VCX08FT OTHERS X7001 CRYSTAL OSCILLATOR ASS1174 IC7403 TC74VCX574FT (85MHz) IC7451 TC74VHC08FT Q7406 2SA1586 Q7405 HN1C01FU [MIKE BLOCK] Q7403,Q7407,Q7408 RN1303...
Page 146
Mark No. Description Part No. Mark No. Description Part No. L7516,L7519 LCTAWR22J2520 COILS AND FILTERS L7505,L7507 LCTAWR68J2520 F7506 SAW FILTER VTF1177 F7405-F7408 ATF1209 F7503 SAW FILTER VTF1179 L7301 ATH1127 F7504 IF TRAP FILTER VTF1180 CAPACITORS F7505 IF TRAP FILTER VTF1181 C7483 (330uF/6.3V) ACH1365 F7501 TRAP FILTER...
Page 147
Mark No. Description Part No. Mark No. Description Part No. X7501 CERAMIC RESONATOR VSS1189 Other Resistors RS1/16S###J (18.432 MHz) > U7501 TV FRONTEND AXF1119 OTHERS JA7703 6P PIN JACK AKB1300 JA7704 PINJACK+MINI DIN 4P AKB1307 [AV IO BLOCK] JA7705 RGB CONNECTOR AKB1311 SEMICONDUCTORS JA7701 RGB CONNECTOR...
6. ADJUSTMENT 1. At shipment, the unit is adjusted to its best conditions. Normally, it is not necessary to readjust even if an assembly is replaced. If the adjustment is shifted or if it becomes necessary to readjust because of part replacement, etc., perform the adjustment as described below. 2.
6.3 USING RS-232C COMMANDS For the PDP-434HD and -504HD series Plasma Displays, the circuitry is structured as shown in the diagram below to support the SR+ system. Controlling with either the SR+ system or RS-232C commands can be selected. As the SR+ system is selected at shipment, to control with RS-232C commands in servicing it is necessary to switch the paths.
6.4 ADJUSTMENT ITEMS If readjustment is necessary because of adjustment error at shipment, perform adjustments as shown below. ¶ Adjustment Points AV BOARD ASSY Rear side SIDE A SIDE A SIDE B PDP-R04E...
Page 154
1 AFC Adjustment Equipment : SG, Digital mutimeter / Tester Condition : Input RF level 75dBµV PAL-B/G White bar 100% START Adjust TP7501 to 2.5 ± 0.1V Select 175.25 MHz Digital multimeter / Tester L7504 (AV BOARD Assy)(1/8) TP7501 (AV BOARD Assy) RF-AGC Adjustment Equipment : SG, Digital mutimeter / Tester Condition : Input RF level 68dBµV...
Page 155
L'AFC Adjustment Equipment : SG, Digital mutimeter / Tester Condition : Input RF level 75dBµV SECAM-L' Color bar START Adjust TP7506 to 2.5 ± 0.1V Select 50.50 MHz Digital multimeter / Tester VR7503 (AV BOARD Assy)(1/8) TP7506 (AV BOARD Assy) Video Level Adjustment Equipment : SG Condition : Input RF level 75dBµV...
6.5 TRAP SWITCH ¶ Outline and Notes For video data transmission from the Media Receiver to the PDP-434HD and PDP-504HD-series Plasma Displays, digital signals are used. Therefore, this unit adopts the HDCP (High-bandwidth Digital Content Protection) system for copyright protection. This unit is also provided with a detection switch (TRAP switch) that will prohibit the unit from being turned on again "if the upper plate of the unit is accidentally opened,"...
About connections • Connect the SR OUT connector of a Pioneer product having that connector (a DVD in the following example) and the SR IN connector of the Media Receiver, using the SR cable. As the remote control sensor is not provided with the Media Receiver, this connection is required for using the remote control unit if the panel is not available.
6.7 SERVICE FACTORY MODE To operate in Service Factory mode, use the supplied remote control unit. Operation in Service Factory mode ¶ Functions whose settings are set to OFF The settings for the following functions are set to OFF when Service Factory mode is entered (including when the "FAY" command is received): •...
Page 159
Changes of the Service Factory menus 1 INFORMATION mode 6 INITIALIZE mode 1. VERSION 1. SYNC DET 2. SERIAL 2. DRIVE MODE MUTE 3. PANEL PD 3. SIDE MASK LEVEL 4. PANEL SD 4. PANEL REVICE 5. MR NG 5. FINAL SETUP 6.
Page 160
Indications in Service Factory mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N F O R M A T I O N V D 1 –...
Page 161
¶ SIG-Mode Table The signal mode is displayed in three characters: First character: Resolution of the input signal (numerics for the video signals, and alphabetics for the PC signals) Second character: Grouping of the V frequencies SIG-Mode table for video signals (resolutions and V frequencies) Vertical Frequency Horizontal Frequency SIG-Mode...
Page 162
2nd Character Reference V Frequency Remarks – – No signal For interpolation of 72-Hz area For distinguishing between 70-Hz or 75-Hz area 9 (spare) – – Out of range Third character: Selection of the screen size by the user is displayed. (?: available, ×: not available) 3rd Character Description on GUI...
Page 163
1 INFORMATION mode ¶ Operation items Function / Display Content VERSION (1) The flash memory versions for each device are displayed. (common part) VERSION (2) The flash memory versions for each device are displayed. (individual part) SERIAL For displaying the serial number of the product (not used) PANEL PD Power-down generated on the panel side and its time of occurrence are displayed.
Page 164
4. PANEL PD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N F O R M A T I O N V D 1 –...
Page 165
6. MR NG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N F O R M A T I O N V D 1 –...
Page 166
8. HOUR METER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N F O R M A T I O N V D 1 –...
Page 167
12. DIGITAL EEPROM When the DIGITAL Assy of the PDP is to be replaced, the adjustment values in it can be temporarily stored in the ROM then be written on the new Assy after replacement. (This function is not supported for initially produced products. It is planned for this function to be supported as soon as it becomes possible.) Whether adjustment has been made on the DIGITAL Assy of the PDP or not (i.e., in the state of a new service part), and whether the data on any adjustment values are retained in the backup ROM or not are displayed.
Page 168
13. HDMI SIGNAL INFO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N F O R M A T I O N I N 1 –...
Page 169
2 FUNCTION CHECK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 No last memory in this menu F U N C T I O N...
Page 170
5 OPTION mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 O P T I O V D 1 –...
Page 171
6 INITIALIZE mode (For managing switching of the initial settings and destination setting) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 I N I T A L I Z E V D 1 –...
6.8 LIST OF RS-232C COMMANDS RS-232C commands can be used in Service Factory mode. Before using RS-232C commands, it is necessary to change the factory presetting. See "6.3. USING RS-232C COMMANDS." Command Operation Remarks Adjusting power consumption Transmitting the backup data to the DIGITAL Assy Any RS-232C command to the Media Receiver becomes disabled as soon as this UART setting: SR+ (9600 BPS) command is issued.
Page 173
Command Operation Remarks Input selection: Input 1 Input selection: Input 2 Input selection: Input 3 Input selection: Input 4 Input selection: Input 5 Selection of the tuner for terrestrial analog signals (Antenna A) Selection of the tuner for terrestrial analog signals (Antenna B) Selection of the tuner for terrestrial digital signals Selection of the tuner for satellite digital signals (BS) Selection of the tuner for satellite digital signals (CS1)
Page 174
Command Operation Remarks AD MAIN R GAIN AD MAIN R OFFSET AD MAIN G GAIN AD MAIN G OFFSET AD MAIN B GAIN AD MAIN B OFFSET Panel W/B B-HIGH adjustment Panel W/B B-LOW adjustment Panel W/B G-HIGH adjustment Panel W/B G-LOW adjustment Turning the power OFF Panel W/B R-HIGH adjustment Panel W/B R-LOW adjustment...
6.9 OUTLINE OF COMMANDS GET Commands GS1: Returning information on the model and the version of the software Data Size Order Data on the display 3 bytes Version of the module microcomputer 4 bytes Version of the IC4-MANTA 4 bytes Sequence version (50VIDEO) 4 bytes Sequence version (50PC)
Page 176
GPD: Returning the power-down data (log) of the PDP Data Size Data Size Order Order Latest "1st PD" data 1 byte Fifth latest “1st PD” data 1 byte Latest "2nd PD" data 1 byte Fifth latest “2nd PD” data 1 byte Data of hour meter for the latest PD 7 bytes Data of hour meter for the fifth latest PD...
Page 177
GSD: Returning the shutdown data (log) of the PDP Order Data Size Order Data Size Latest SD data 1 byte Fifth latest SD data 1 byte Data of subcategory for the latest SD 1 byte Data of subcategory for the fifth latest SD 1 byte Data of hour meter for the latest SD 7 bytes...
Page 178
GNG: Returning the data (logs) on power-down and shutdown of the Media Receiver Data Size Data Size Order Order Latest NG data 1 byte Fifth latest NG data 1 byte Data of subcategory for the latest NG 1 byte Data of subcategory for the fifth latest NG 1 byte Data of MR hour meter for the latest NG 7 bytes...
Page 179
GAJ: Returning drive-related adjustment values of the PDP Order Data Size Data Table Currently used ABL table 3 bytes ABL table for NTSC Upper limit of the electric power 3 bytes ABL table for PAL Vsus adjustment value 3 bytes ABL table for PC Vofs adjustment value 3 bytes...
7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 TROUBLE SHOOTING Image for the composite or S signal is not displayed Image for the composite or TV signal is not displayed S signal is not displayed on the screen. Is the function corresponding No Select the corresponding Is the Input selector set to Set the Input selector to TV.
Page 181
MONITOR OUT image is not displayed MONITOR OUT image is not displayed Only the component and RGB signals can be output Is a signal being input other from MONITOR OUT. Check than the component or RGB the unit using either the signal? component or RGB signal.
Page 182
Image for the component or RGB signals is not displayed Image for the component or Image from the PC card is RGB signals is not displayed not displayed Is the function corresponding Is the Function correspond- No Select the corresponding No Select the corresponding to selected signal input ing to selected signal input...
Page 183
No sound from the headphones No sound from the No sound from MONITOR headphones Cancel muting then check Cancel muting then check Is sound muting set? Is sound muting set? again. again. Raise the volume then Raise the volume then Is the volume set to 0? Is the volume set to 0? check again.
Page 184
No sound from the speakers (1/2) No sound from the speakers Cancel muting then check Is sound muting set? again. Raise the volume then Is the volume set to 0? check again. Are the headphones Disconnect the headphones connected? then check again. Is it only the VIDEO 3 Is it the only TV sound that sound that doesn't come...
Page 185
No sound from the speakers (2/2) No sound from the sub-woofer Is it sound for every function Cancel muting then check that doesn't come out? Is sound muting set? again. Check around IC8002 and Is a signal output from Raise the volume then check the communications IC8002? Is the volume set to 0?
7.1.2 DISASSEMBLY Metal bonnet top and bottom Remove the metal bonnet top by removing the six screws. Remove the six hooks. Remove the metal bonnet bottom by removing the five screws. Caution : Please remove it after pulling it in a rear direction because metal bonnet top and bottom are hard to reduce.
Page 192
Front shield A and Center stay Remove the front shield A by removing the ten screws. Disconnect the three connectors and the one flexible cable. Remove styling of the two cables. Remove styling of the one flexible cable. Remove the center stay by removing the three screws. Center stay ×...
Cable Styling in the Assembly Front Panel Assy Senter Stay 16pin Housing Wire (J112) Front Panel Assy Flexible Cable (J205) AV BOARD Assy Hold down 16pin Housing Wire (J112) under Flexible Cable (J205) like this figure. 16pin Housing Wire (J112) let this part going through. Keep Flexible Cable (J205) and 16pin Housing Wire (J112) apart from each other.
7.3 PARTS 7.3.1 IC • The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. List of IC AD9883AKST-110, SM5301BS, BA7078AF, Sil9993CTG100, HY57V643220CT-7, MBM29PL3200BE70PFV, Sil170BCLG64, CXA2069Q, MSP3417G, MBM29LV160TE-90PFTN, HY57V641620HGT-7, TDA9818TS, TA1287FG, SDA6000, AXF1119, AXY1066, AXY1070 AD9883AKST-110 (MR MAIN BOARD ASSY : IC6402) •...
Page 198
Pin Function Pin Name Pin Function − Ground GREEN 7 Converter Green output (MSB) GREEN 6 Converter Green output GREEN 5 Converter Green output GREEN 4 Converter Green output GREEN 3 Converter Green output GREEN 2 Converter Green output GREEN 1 Converter Green output GREEN 0 Converter Green output...
Page 199
Pin Name Pin Function − Analog power supply (3.3V) − Ground GAIN Analog input for converter G SOGIN Input for Sync-on Green − Ground − Analog power supply (3.3V) − Analog power supply (3.3V) − Ground RAIN Analog input for converter R Address input 1 of serial port Data clock (max.
Page 201
Pin Function Pin Name Pin Function Analog GINA or UINA signal input. Sync signal is input on SYNCIN pin. GSG1 GOUT/UOUT output buffer gain set input Analog GINB or UINB signal input. Sync signal is input on SYNCIN pin. − (NC) No connection Analog BINA or VINA signal input.
Page 202
BA7078AF (MR MAIN BOARD ASSY : IC6604) • Multimedia IC Block Diagram HSCTL POLH H SYNC DET. C / HSYNC IN EXIH VIDEO IN POLV SYNC SEPA. VSEPA EXIV HOR. SYNC CONTROL V SYNC SEPA. VSYNC IN CVPOL HDRV V SYNC DET. CVEXI CLAMP CPSEL...
Page 203
Pin Function Pin Name Pin Function HDRV output Used to select whether to output the VDRV section of the HDRV output signal. HSCTL High : VDRV section of HDRV is output Low : VDRV section of HDRV is not output Composite sync / H SYNC input Input either the composite synchronization signal or the horizontal synchronization signal.
Page 205
Pin Function No. Pin Name I/O Pin Function No. Pin Name I/O Pin Function − DACVCC DAC power supply (3.3V) 24-bit output pixel data bus − DACGND DAC ground 24-bit output pixel data bus − No connection 24-bit output pixel data bus −...
Page 206
HY57V643220CT-7 (MR MAIN BOARD ASSY : IC7001, IC7002) • Synchronous DRAM Block Diagram 2 DQ0 Self Reflesh Logic Reflesh & Timer Counter 4 DQ1 5 DQ2 512 k × 32 Bank 3 Row Active 512 k × 32 Bank 2 7 DQ3 Decoder 512 k ×...
Page 207
Pin Function No. Pin Name I/O Pin Function No. Pin Name I/O Pin Function − − Power supply Ground I/O Data input/output DQ24 I/O Data input/output − − VDDQ Power supply for output buffer VSSQ Ground for output buffer I/O Data input/output DQ25 I/O Data input/output I/O Data input/output...
Page 209
Sil170BCLG64 (MR MAIN BOARD ASSY : IC7401) • HDCP Panel Link Transmitter Pin Arrangement (Top view) G ND SCLS RESERVED G ND SDAS ISEL/RST# M S E N HTPLG C T L 3 VSYNC H S Y N C VREF PGND2 Block Diagram MSEN...
Page 210
Pin Function Pin Name Pin Function − Digital power supply (3.3V) Data enable VREF 3.3V fixed HSYNC Horizontal sync. control signal input VSYNC Vertical sync. control signal input CTL3 External CTL3 input − No connection − No connection HTPLG Monitor chrage input Power down input (Active low) MSEN Monitor sense output (open-collector output)
Page 211
Pin Name Pin Function 24-bit pixel bus input 24-bit pixel bus input − PGND2 PLL analog ground − PVCC2 Analog power supply for filter PLL (3.3V) 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input 24-bit / 12-bit pixel bus input...
Page 213
Pin Function Pin Name Pin Function Video signal inputs. Input composite video signals. Y/C separation signal inputs. Input luminance signals. The YIN1 pin inputs the signal obtained by Y/C separating the VOUT1 pin output. YIN1 Y/C separation signal inputs. Input chrominance signals. The CIN1 pin inputs the signal obtained by Y/C separating the VOUT1 pin output.
Page 214
Pin Name Pin Function Composite video/S selector. The detection results are written to the status register. − S signal at 3.5 V or less. Composite video signal at 3.5 V or more. This pin is pulled up to 5 V by a 100 k ohm resistor, so the composite video signal is selected when open.
Page 216
Pin Function NC = Not connected; leave vacant X = obligatory; connect as described in circuit diagram LV = if not used, leave vacant AHVSS: connect to AHVSS DVSS: if not used, connect to DVSS Connection Pin Name Type Descriptiom (it not used) AVSUP Analog power supply +5V...
Page 219
HY57V641620HGT-7 (AV BOARD ASSY : IC9104) • 64M bit (4M × 16) Synchronous DRAM Block Diagram 2 DQ0 Self Reflesh Logic Internal Row & Timer Counter 4 DQ1 5 DQ2 1M × 16 Bank 3 Row Active 1M × 16 Bank 2 7 DQ3 Decoder 1M ×...
Page 220
Pin Function No. Pin Name I/O No. Pin Name I/O Pin Function Pin Function − − Power supply Ground I/O Data input/output Address input − VDDQ Power supply for output buffer Address input I/O Data input/output Address input I/O Data input/output Address input −...
Page 221
TDA9818TS (AV BOARD ASSY : IC7501) • Single/multistandard VIF/SIF-PLL and FM-PLL/AM Demodulators Pin Arrangement (Top view) Pin Function Pin Name Pin Function VIF1 VIF differential input signal voltage 1 VIF2 VIF differential input signal voltage 2 VIF1 SIF2 Standard selection switch VIF2 SIF1 CVAGC...
Page 223
AXF1119 (AV BOARD ASSY : U7501) • TV Tuner Pin Arrangement 1 2 3 4 5 6 7 Pin Function Pin Name BB (5V) +B (5V) BT (31V) IF OUT ANT IN PDP-R04E...
Page 229
Pin Function Second No. Pin Name Pin Function Function − Clock for JTAG interface − Control signal for JTAG interface − Data input for JTAG interface − O Data output for JTAG interface P2.8 EX0IN I/O General purpose I/O port/External interrupt 0 P2.9 EX1IN I/O General purpose I/O port/External interrupt 1...
Page 230
Second No. Pin Name Pin Function Function − 51 D15 I/O Data bit − − 52 VSS33-4 Digital ground for pads − − 53 VDD33-4 Digital power (for pads) (3.3 V) − 54 D7 I/O Data bit − 55 D0 I/O Data bit −...
Second No. Pin Name Pin Function Function 101 P6.6 SDA2 I/O General purpose I/O port/I2C bus data line 2 102 VSYNC I/O Vertical sync In/output/Composite sync output − 103 HSYNC I/O Horizontal sync In/output 104 COR RSTOUT O Output for contrast reduction/Reset output 105 BLANK CORBLA O Fast blanking signal/Three-level signal for contrast reduction + fast blanking...
8. PANEL FACILITIES Media Receiver Front view 1 2 3 Pull this section to open the door . 6 INPUT 4 terminal (VIDEO) 1 POWER button 7 INPUT 4 terminals (AUDIO) 2 POWER ON indicator 3 STANDBY indicator 8 PC INPUT terminal (AUDIO) 9 PC INPUT terminal (ANALOG RGB) 4 PHONES output terminal 0 PC CARD slot...
Page 233
Remote control unit Sets the sound multiplex mode. 9 Colour (RED/GREEN/YELLOW/BLUE) TELETEXT mode: Selects a page. 0 EPG Displays the Electronic Programme Guide. TELETEXT mode: Displays hidden characters. (RETURN) Restores the previous menu screen / / / Selects a desired item on the setting screen. Displays the channel information.