AudioCodes Mediant 500Li Quick Setup Manual
  1. Manuals
  2. Brands
  3. AudioCodes Manuals
  4. Gateway
  5. Mediant 500Li MSBR
  6. Quick setup manual
AudioCodes Mediant 500Li Quick Setup Manual

AudioCodes Mediant 500Li Quick Setup Manual

Analog voip gateway
Hide thumbs Also See for Mediant 500Li:
Table of Contents

Advertisement

Quick Links

Download this manual
Mediant™ 500Li
Analog VoIP Gateway
Quick Setup Guide
Welcome
Thank you for choosing AudioCodes' Mediant 500Li Analog VoIP Gateway.
This document is intended to provide basic instructions for initial setup of the Mediant 500Li (hereafter,
referred to as device) and connecting it to your network. For advanced configuration, please refer to the
device's Configuration Notes and Hardware Manual respectively, which can be downloaded from AudioCodes
Website at https://www.audiocodes.com/library/technical-documents.
Before you begin, please read the
Safety Precautions
and click
here
to view the Regulatory Information
document.
1 |
P a g e

Advertisement

Table of Contents
loading

Related Manuals for AudioCodes Mediant 500Li

Summary of Contents for AudioCodes Mediant 500Li

  • Page 1 Thank you for choosing AudioCodes’ Mediant 500Li Analog VoIP Gateway. This document is intended to provide basic instructions for initial setup of the Mediant 500Li (hereafter, referred to as device) and connecting it to your network. For advanced configuration, please refer to the device's Configuration Notes and Hardware Manual respectively, which can be downloaded from AudioCodes Website at https://www.audiocodes.com/library/technical-documents.

  • Page 2: Safety Precautions

    Safety Precautions This device is an indoor unit and therefore, must not be installed outdoors.  Ethernet cabling must be routed only indoors and must not exit the building.  Do not open or dismantle the device.  Do not expose the device to water or moisture. ...
  • Page 3 Physical Description of Front Panel Power LED indicating power status: Green On Power received by device. No power. Status LED indicating operating status: Green On Device is operational. Green Flashing Initial rebooting stage or software upgrade in process. Red On Boot failure.
  • Page 4 Physical Description of Rear Panel POWER DC power plug entry for external AC/DC power adapter. CONSOLE RJ-45 port for RS-232 serial communication with the device. Reset pinhole button for resetting the device or restoring it to factory defaults. To restore to factory defaults: with a paper clip or any other similar pointed object, press and hold down the button for at least 12 seconds (but no more than 25 seconds).

  • Page 5: Mounting The Device

    The bumpers avoid involuntary movement of the unit on the desktop as well as enable better air flow for cooling the device. Mounting it in a standard 19-inch rack by placing it on AudioCodes 1U 19-inch rack mount shelf ...

  • Page 6: Initial Connectivity

    Initial Connectivity This section describes how to initially access the device's management interface and change its default IP address to correspond with your networking scheme. Device management can always be done through the LAN interface, but you can also enable device management through the WAN (as explained in the configuration guide).
  • Page 7 Make sure that your computer is configured to automatically obtain an IP address. The device has an embedded DHCP server, which by default, allocates IP addresses to connected computers. On your computer, start a Web browser and in the URL address field, enter the device's default IP address;...
  • Page 8 Configuring WAN Interface This section describes how to configure the WAN interface, which uses Gigabit Ethernet. Before configuring the WAN interface, make sure that you have all the required information from your Internet service provider. Connect the WAN port to the WAN network. For information on cabling the WAN port, refer to the Hardware Installation Manual.

  • Page 9: Cabling The Device

    Cabling the Device Cabling depends on your ordered hardware interfaces, for example, the type of WAN interface. Connect the device's WAN port interface to your router. Connect any phone, fax or other PSTN equipment to any of the analog port interfaces (FXS). Insert the DC plug that is located at the end of the power cord of the supplied power adapter into the device's power socket located on the rear panel and labeled POWER.
  • Page 10 ©2022 AudioCodes Ltd. All rights reserved. AudioCodes, AC, HD VoIP, HD VoIP Sounds Better, IPmedia, Mediant, MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice, AudioCodes Meeting Insights, AudioCodes Room Experience and CloudBond are trademarks or registered trademarks of AudioCodes Limited.

Table of Contents