Lincoln Electric VRTEX ENGAGE Operator's Manual page 8

For use with machines having code numbers: 12497, 12498, 12499, 12500
Table of Contents

Advertisement

VRTEX ® ENGAGE™
BIBLIOGRAPHY AND SUGGESTED READING
ANSI Z87.1, Practice for Occupational and Educational Eye and Face
Protection, American National Standards Institute, 11 West 42nd
Street, New York, NY 10036.
Arc Welding and Your Health: A Handbook of Health Information for
Welding. Published by The American Industrial Hygiene Association,
2700 Prosperity Avenue, Suite 250, Fairfax, VA 22031-4319.
NFPA Standard 51B, Cutting and Welding Processes, National Fire
Protection Association, 1 Batterymarch Park, P.O. Box 9146, Quincy,
MA 02269-9959.
OSHA General Industry Standard 29 CFR 1910 Subpart Q. OSHA
Hazard Communication Standard 29 CFR 1910.1200. Available from
the Occupational Safety and Health Administration at http://www.
osha.org or contact your local OSHA office.
The following publications are published by The American Welding
Society, P.O. Box 351040, Miami, Florida 33135. AWS publications
may be purchased from the American Welding society at http://www.
aws.org or by contacting the AWS at 800-443-9353.
LISTED BELOW ARE SOME TYPICAL INGREDIENTS IN WELDING ELECTRODES AND
INGREDIENTS
Aluminum and/or aluminum alloys (as AI)*****
Aluminum oxide and/or Bauxite*****
Barium compounds (as Ba)*****
Chromium and chromium alloys or compounds (as Cr)*****
Fluorides (as F)
Iron
Limestone and/or calcium carbonate
Lithium compounds (as Li)
Magnesite
Magnesium and/or magnesium alloys and compounds (as Mg)
Manganese and/or manganese alloys and compounds (as Mn)*****
Mineral silicates
Molybdenum alloys (as Mo)
Nickel*****
Silicates and other binders
Silicon and/or silicon alloys and compounds (as Si)
Strontium compounds (as Sr)
Zirconium alloys and compounds (as Zr)
Supplemental Information:
(*) Not listed. Nuisance value maximum is 10 milligrams per cubic
meter. PEL value for iron oxide is 10 milligrams per cubic meter.
TLV value for iron oxide is 5 milligrams per cubic meter.
(**) As respirable dust.
(*****) Subject to the reporting requirements of Sections 311, 312,
and 313 of the Emergency Planning and Community Right-to-
Know Act of 1986 and of 40CFR 370 and 372.
(b) The PEL for chromium (VI) is .005 milligrams per cubic meter
as an 8 hour time weighted average. The TLV for water-soluble
chromium (VI) is 0.05 milligrams per cubic meter. The TLV for
insoluble chromium (VI) is 0.01 milligrams per cubic meter.
THEIR TLV (ACGIH) GUIDELINES AND PEL (OSHA) EXPOSURE LIMITS
ANSI, Standard Z49.1, Safety in Welding, Cutting and Allied
Processes. Z49.1 is now available for download at no charge at http://
www.lincolnelectric.com/community/safety/ or at the AWS website
http://www.aws.org.
AWS F1.1, Method for Sampling Airborne Particulates Generated by
Welding and Allied Processes.
AWS F1.2, Laboratory Method for Measuring Fume Generation Rates
and Total Fume Emission of Welding and Allied Processes.
AWS F1.3, Evaluating Contaminants in the Welding Environment: A
Strategic Sampling Guide.
AWS F1.5, Methods for Sampling and Analyzing Gases from Welding
and Allied Processes.
AWS F3.2, Ventilation Guide for Welding Fume Control.
AWS F4.1, Recommended Safe Practices for the Preparation for
Welding and Cutting of Containers and Piping That Have Held
Hazardous Substances.
AWS SHF, Safety and Health Facts Sheets. Available free of charge
from the AWS website at http://www.aws.org.
CAS No.
7429-90-5
1344-28-1
513-77-9
7440-47-3
7789-75-5
7439-89-6
1317-65-3
554-13-2
1309-48-4
7439-95-4
7439-96-5
1332-58-7
7439-98-7
7440-02-0
1344-09-8
7440-21-3
1633-05-2
12004-83-0
c) Values are for manganese fume. STEL (Short Term Exposure
Limit) is 3.0 milligrams per cubic meter. OSHA PEL is a ceiling
value.
(****) There is no listed value for insoluble barium compounds. The
TLV for soluble barium compounds is 0.5 mg/m3.
TLV and PEL values are as of April 2006. Always check Material
Safety Data Sheet (MSDS) with product or on the Lincoln Electric
website at http://www.lincolnelectric.com
SAFETY
TLV mg/m
PEL mg/m
3
3
10
15
10
5**
****
****
0.5(b)
.005(b)
2.5
2.5
10*
10*
10
15
10*
10*
10
15
10*
10*
0.2
5.0(c)
5**
5**
10
10
1.5
1
10*
10*
10*
10*
10*
10*
5
5

Advertisement

Table of Contents
loading

Table of Contents