Page 1
Serial #: ___________________________ Date Purchased: _____________________ Installation & Operation Manual Gas Skillets GMTS-30, GMTS-40 & GMTS-60 Model GMTS-60 WARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
Gas Skillets Table of Contents RETAIN THIS MANUAL FOR FUTURE REFERENCE. Table of Contents Important Notes For Installation and Operation ..............2 Service Connections ......................4 Installation Instructions ......................6 Operating Instructions ......................8 Cleaning ..........................10 Cooking Guidelines ....................... 11 Maintenance .........................
29.3 Back [334 kg] (152 mm) * For use on non-combustible floors only. As continued product improvement is a policy of Crown, specifications are subject to changge without notice. PAGE OF 24 INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21)
Page 5
(152 mm - 356 mm) (279 mm - 356 mm) * For use on non-combustible floors only. As continued product improvement is a policy of Crown, specifications are subject to changge without notice. INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21) PAGE...
Installation Gas Skillets Installation Instructions NPACKING IMMEDIATELY INSPECT FOR SHIPPING DAMAGE Immediately after unpacking the appliance, check for possible shipping damage. If the gas fired tilting skillet is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, verify that the type of gas supply (natural or propane) and electrical service agree with the specifications on the rating plate located on the left side panel as you face the front of the appliance.
Page 7
Gas Skillets Installation Gas Connections WARNING Do not connect the appliance to the electrical supply until after the gas connection has been made. WARNING Never use an open flame to check for gas leaks. Check all connections for leaks using soapy water before use. CAUTION The pipe thread compound used when installing pipes must be a type that is resistant to the action of liquified petroleum or propane gases.
Operation Gas Skillets Operating Instructions WARNING The tilting braising pan and its parts are hot. Use care when operating, cleaning and servicing the tilting braising pan. Before First Use Using a non-corrosive, grease-dissolving commercial cleaner, clean the protective metal oils from all surface parts and the interior of the tilting braising pan.
Page 9
Gas Skillets Operation Daily Shutdown Procedure 1. To turn tilting braising pan of, turn THERMOSTAT dial to OFF. 2. To turn power to tilt motor OFF, turn power switch to OFF. Tilting the Braising Pan 1. DO NOT try to tilt braising pan with lid down. Turn MOTOR switch on. 2.
Cleaning Gas Skillets Cleaning WARNING Disconnect the power supply to the appliance before cleaning or servicing. WARNING The appliance and its parts are hot. Use care when operating, cleaning and servicing the skillet. CAUTION Do not use cleaning agents that are corrosive. After each use, allow the tilting braising pan to cool before cleaning.
Maintenance Gas Skillets Maintenance NOTICE Contact the factory, factory representative or local service company to perform maintenance and repairs. WARNING The tilting braising pan and its parts are hot. Use care when operating, cleaning and servicing the tilting braising pan. WARNING Disconnect the power supply to the appliance before cleaning or servicing.
Page 13
Gas Skillets Maintenance Relief Valve The relief valve is located underneath an aluminum hexagon cover on the side of the custom manifold block. This relief valve is factory set to 825 P.S.I. and locked and should not be adjusted. If adjustments are necessary, remove the hexagon cover which will give access to the relief valve screw. With the pump running, and with a suitable flat blade style screwdriver, rotate the screw clockwise to increase pressure, and anti clockwise to decrease pressure.
Troubleshooting Gas Skillets Troubleshooting Burners No Not Come On 1. Gas supply to unit is “OFF”. 2. Manual shut off valve is “OFF”. 3. Thermostat is not turned “ON”. 4. Pan not in lowest position. 5. Ignition control not functioning. Burners Produce Carbon Deposits 1.
Page 15
Gas Skillets Troubleshooting Overheating of System 1. Continuous operation at relief setting. 2. Excessive slippage or internal leakage. 3. Fluid viscosity too high or low. 4. Hose I.D. too small causing high velocity. 5. Improper air circulation around reservoir. 6. System relief valve set too high. 7.
Material Safety Data Sheets Gas Skillets PAGE OF 24 INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21)
Page 17
Gas Skillets Material Safety Data Sheets INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21) PAGE OF24...
Page 18
Material Safety Data Sheets Gas Skillets PAGE OF 24 INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21)
Page 19
Gas Skillets Material Safety Data Sheets INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21) PAGE OF24...
Page 20
Material Safety Data Sheets Gas Skillets PAGE OF 24 INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21)
Page 21
Gas Skillets Material Safety Data Sheets INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21) PAGE OF24...
Page 22
Material Safety Data Sheets Gas Skillets PAGE OF 24 INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21)
Page 23
Gas Skillets Material Safety Data Sheets INSTALLATION & OPERATION MANUAL 10094 REV 0 (08/21) PAGE OF24...
Page 24
GMTS-30, GMTS-40 & GMTS-60 Gas Skillets A product with the Crown name incorporates the best in durability and low maintenance. We all recognize, however, that replacement parts and occasional professional service may be necessary to extend the useful life of this appliance.