Stihl HLE 71 Instruction Manual page 36

français
invites accidents.d)Remove any adjusting key or
wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of
the power tool may result in personal injury.e)Do
not overreach. Keep proper footing and balance
at all times. This enables better control of the
power tool in unexpected situations.f)Dress prop-
erly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.g)If devices
are provided for the connection of dust extraction
and collection facilities, ensure these are con-
nected and properly used. Use of dust collection
can reduce dust-related hazards.
23.4 4) Power tool use and care
a)Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.b)Do not use the
power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with
the switch is dangerous and must be
repaired.c)Disconnect the plug from the power
source and/or the battery pack from the power
tool before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of start-
ing the power tool accidentally.d)Store idle power
tools out of the reach of children and do not
allow persons unfamiliar with the power tool or
these instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.e)Maintain power tools. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If dam-
aged, have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.f)Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cut-
ting edges are less likely to bind and are easier
to control.g)Use the power tool, accessories, tool
bits etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
23.5 5) Service
a)Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
36
23.6 Hedge Trimmer Safety Warn-
ings
- Keep all parts of the body away from the cut-
ting blades. Do not remove cut material or
hold material to be cut when blades are mov-
ing. Make sure the switch is off when clearing
jammed material. A moment of inattention
while operating the hedge trimmer may result
in serious personal injury.
- Carry the hedge trimmer by the handle with
the cutting blades stopped. When transporting
or storing the hedge trimmer always fit the
blade scabbard. Proper handling of the hedge
trimmer will reduce possible personal injury
from the cutting blades.
- Always hold your electric power tool by the
insulated handles because the cutting blades
may contact hidden electrical wires or your
own power cord. Any blade contact with a live
wire may energize metallic parts of the power
tool and result in an electric shock.
- Keep the power cord away from cutting area.
During operation the power cord may be hid-
den in shrubs and can be accidentally severed
by the blade.
Table des matières
1 Indications concernant la présente Notice
d'emploi.....................................................37
2 Prescriptions de sécurité et techniques de
travail........................................................ 37
3 Utilisation.................................................. 42
4 Montage du tube....................................... 44
5 Montage de la poignée circulaire.............. 44
6 Montage du réducteur...............................45
7 Réglage de la barre de coupe...................45
8 Utilisation du harnais.................................46
9 Branchement électrique............................ 47
10 Mise en marche........................................ 48
11 Arrêt.......................................................... 48
12 Disjoncteur de surcharge.......................... 48
13 Graissage du réducteur............................ 48
14 Rangement............................................... 49
15 Affûtage.....................................................49
16 Instructions pour la maintenance et l'entre-
tien............................................................ 50
17 Conseils à suivre pour réduire l'usure et évi-
ter les avaries............................................50
18 Principales pièces..................................... 51
19 Caractéristiques techniques......................51
20 Instructions pour les réparations............... 52
21 Mise au rebut............................................ 53
22 Déclaration de conformité UE................... 53
0458-277-9621-B