To Memorize Channels; Tv Operation - Toshiba 22LV506 Service Manual

Basic setup
To memorize channels (Continued)
Add/Delete channel
You can select the channel that you want to skip.
1 Press MENU in the TV mode. The TV menu 4
screen will appear. Press or to select
"Channel", then press or ENTER.
Main Menu
Picture
Audio
Channel
Lock
Setup
: Select ENTER:Set
5
2 Press or to select "Add/Delete", then
press or ENTER.
Channel
Add/Delete >>
Auto Ch Memory >>
Ch Label >>
: Select ENTER:Set
6
3 Press or to select "Add/Delete", then
press or ENTER.
7
Add/Delete
Adding Channel >>
Add/Delete >>
Clear All >>
: Select ENTER:Set
24

TV operation

TV operation
TV operation
1 To turn on the TV/DVD, press POWER.
(POWER indicator on the front of the unit changes
green. It may take approx. 10 seconds for a picture
to appear on screen.)
2 Adjust the volume level by pressing VOL + or – .
The volume level will be indicated on the screen
by orange bars. As the volume level increases, so
do the number of bars. If the volume decreases,
the number of orange bars also decreases.
3 Set the Signal Type option to the appropriate
position (see "Air/Cable selection" on page 23).
Air - VHF/UHF channels
Cable - Cable TV channels
VHF/UHF/CABLE CHANNELS
4 Press the Direct Channel Selection (0-9, –)
buttons or CH / to select the channel.
(If you press only channel number, channel
selection will be delayed for a few seconds.)
Note:
•
•
26
ENTER
/ / /
EXIT/CANCEL
MENU
Press or to select the channel that you
want to skip.
Add/Delete
CH Signal
2 Analog Add
3 Analog Add
3-001 Digital Delete
3-002 Digital Add
4 Analog Delete
: Select : Adjust
Press or to select "Add" or "Delete",
whichever function you want to perform.
Add/Delete
CH Signal
2 Analog Delete
3 Analog Add
3-001 Digital Delete
3-002 Digital Add
4 Analog Delete
: Select : Adjust
Repeat steps 4 - 5 for other channels you
want to add or delete.
Press EXIT/CANCEL to return to the normal
screen.
POWER
0–9, –
VOL +/–
CH /
TO SELECT ANALOG CHANNELS
1-9: Press 1-9 as needed. Example, to
select channel 2, press 2.
10-99: Press the 2 digits in order. Example, to
select channel 12, press 1, 2.
100-125: Press the 3 digits in order. Example, to
select channel 120, press 1, 2, 0.
TO SELECT DIGITAL CHANNELS
Press the first 3 digits, then press the – button,
followed by the remaining number.
Example, to select channel 015-001, press 0, 1,
5, –, 1.
• If a channel is selected with only audio content,
"Audio only" will be displayed on the screen.
• If a channel is selected with a weak digital
signal, "Digital channel signal strength is low"
will be displayed on the screen.
The same program may be available on either
an analog channel or a digital channel. You may
choose to watch either format.
• If a channel is selected to which you have not
subscribed, "Digital channel is encrypted" will
be displayed on the screen.
Air Cable
VHF VHF
2-13 2-13
UHF STD/HRC/IRC
14-69 14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100) (125)
01 (5A)
If a channel with no broadcast is selected, the sound
will automatically be muted.
It may take a few seconds for a digital channel picture
to appear on screen after being selected.
Adding Channel Clear All
All channels are deleted from the channel memory.
If you find a new channel unregistered, you can add the
new channel into the channel memory.
1 Tune in the new channel.
1
2 Press MENU. The TV menu screen will appear.
Press or to select "Channel", then press
or ENTER.
Main Menu
Picture
Audio
Channel
Lock
Setup
2
: Select ENTER:Set
3 Press or to select "Add/Delete", then
press or ENTER.
Channel
Add/Delete >>
Auto Ch Memory >>
Ch Label >>
3
: Select ENTER:Set
4 Press or to select "Adding Channel",
then press or ENTER. The new channel will
be added into the channel memory.
Add/Delete
Adding Channel >>
Add/Delete >>
Clear All >>
4
: Select ENTER:Set
5 Press EXIT/CANCEL to return to the normal
screen.
TV operation (continued)
DISPLAY SLEEP
Press DISPLAY to display the current information on the To set the TV/DVD to
screen. turn off after a preset
amount of time, press
SLEEP on the remote
control. The clock will
count up 10 minutes for
each press of the SLEEP button (Off, 0h 10m, 0h 20m,
62-001 HDTV Moving Picture1 Sleep Timer
Off
CH-1
Digital Air English ..., 2h 0m). After the sleep time is programmed, the
No Program Information is available
When the TV/DVD display will appear briefly every ten minutes to remind
you that the sleep timer is operating. To confirm the
receives a digital signal,
sleep timer setting, press SLEEP and the remaining
the digital information
Natural
1080i
time will be displayed for a few seconds. To cancel the
will appear.
sleep timer, press SLEEP repeatedly until the display
• Channel number • Station name
turns to Off.
• Channel label (if preset) • Broadcast program name
• V-Chip rating • Signal type
HEAD PHONES
• Sleep timer • Audio language
Insert a stereo headphones (not supplied) with a 1/8" mini
• Program guide • Picture size
plug into the HEAD PHONE jack on the rear panel.
• Resolution
If you connect headphones, the sound from TV/DVD
Sleep Timer speakers is muted.
14
Off
Analog Cable
When the TV/DVD
receives a analog signal,
the analog information
Natural
480i
will appear.
• Channel number • Channel label (if preset)
• V-Chip rating • Signal type
• Sleep timer • Audio information (Stereo or SAP)
• Picture size • Resolution
Press DISPLAY again to clear the call display.
Note:
• After a few seconds, DISPLAY screen will return to
normal TV-operation automatically.
CH RTN
This button allows you to go back to the last channel
selected by pressing CH RTN. Press CH RTN again to
return to the last channel you were watching.
MUTE
Press MUTE to switch off the sound. The TV/DVD's
sound will be silenced and "Mute" will appear on the
screen. The sound can be switched back on by pressing
this button again or the VOL + or –.
ENTER
/ /
EXIT/CANCEL
MENU
Press MENU in the TV mode. The TV menu
screen will appear. Press or to select
"Channel", then press or ENTER.
Main Menu
Picture
Audio
Channel
Lock
Setup
: Select ENTER:Set
Press or to select "Add/Delete", then
press or ENTER.
Channel
Add/Delete >>
Auto Ch Memory
>>
Ch Label >>
: Select ENTER:Set
Press or to select "Clear All", then press
or ENTER.
Add/Delete
Adding Channel >>
Add/Delete >>
Clear All >>
: Select ENTER:Set
Press EXIT/CANCEL to return to the normal
screen.
25
SLEEP
DISPLAY
VOL +/–
MUTE
CH RTN
S l e e p Ti m e r
0 h 1 0 m
27