Hoover H-OVEN STEAM 700 PLUS User Instructions page 13

Quick Guide Hoover OVEN - Enrollment on App
Procedure for devices with Bluetooth 4.0 (or higher)
This quick guide illustrates the steps to follow to enroll your
appliance on the App Hoover Wizard, using a device with
Bluetooth 4.0 (or higher) technology. In this case, the procedure is
simplified and faster (Easy Enrollment).
If you are using a device without Bluetooth technology (or less than
4.0), please follow the instructions described on the next section.
STEP 1
·Mark down the appliance Serial Number.
·Mark down the Wi-Fi Name and Password (WPA/ WEP Key)
which are normally placed on the back of your Wi-Fi router.
NOTES
·The frequency of the home Wi-Fi network has to be set on the 2.4
GHz band. You cannot configure the appliance if your home
network is set to the 5 GHz band.
·If you are having trouble locating the WPA/WEP Password,
please contact your Internet Provider.
Please make sure your smartphone is connected to the same Wi-
Fi network and has the Bluetooth enabled within the "Settings".
Refer to the manual for more details.
STEP 2
·Download the Hoover Wizard App from the Store.
·Open the Hoover Wizard App and create your user profile by
taping on "Register". Accept the privacy policy and fill in the
required fields.
NOTES
·The App is available for Android (version 4.4 or higher) and iOS
(version 8.0 or higher) devices.
·If you already have a Hoover Wizard user profile, you can login
using your credentials.
STEP 3
·In the homepage, tap on the icon with the three bars on the top left
to enter your profile, then tap on "REGISTER NEW APPLIANCE"
and select the name of the product that you want to enroll.
STEP 4
·Insert the purchase date of your appliance (DD/MM/YYYY), then
tap on "Proceed".
STEP 5
·Insert the 16 digits of the serial number or scan the QR code on
the appliance. Tap on "Next". Check data correctness of the data
and tap on "Confirm". Once the system has recognized the
product, tap on "Next".
STEP 6
1)Tap on the icon ONE-FI.
2)Set the oven on ONE-FI RESET (the oven will beep).
3)The WIFI icon will blink.
·In App - Tap on "Confirm". Wait for APP to connect to the
appliance.
NOTES
·Enrollment must be completed within 5 minutes.
·In case of any issue, tap "Retry", making sure you have enabled
Bluetooth on your device (smartphone / tablet). If the process has
not been completed correctly yet, tap on "Proceed with Standard
Enrollment".
·To ensure correct data transfer, we recommend you to stay with
the device close to the appliance.
STEP 7
·Insert the password of your home Wi-Fi network.
·Select the type of password (WEP or WPA), then tap on
"Confirm".
·The enrollment process is now finished.
NOTES
·If this is not automatically synchronised by the App, please insert
the name of your home Wi-Fi network in the first box; pay attention
to the difference between lowercase and uppercase.
IF THE SET UP IS NOT SUCCESSFUL
It's important to establish a good Wi-Fi signal strength between the
home router and the appliance: low Wi-Fi signal strength would
cause the failure of the final stage of the set up. To assess if this is
the case, start the connection process again from Step 1; when
you get to Step 6, when you get to Step 6, place your device
(smartphone or tablet) next to the router and search for
"WIFIOVEN-xyzk" net generated by the appliance. If this does not
come up as an option, it means that the router cannot see the
appliance. In this case, we highly recommend you to bring the
router near the appliance (if possible) or contact your internet
provider to purchase a compatible "Wi-Fi Range Extender" to
increase the signal strenght.
Remote control mode
·Tap on the icon ONE-FI.
·Set the oven on ONE-FI ON (the oven will beep).
·The WIFI icon will blink.
Quick Guide Hoover OVEN - Enrollment on App
Procedure for devices without Bluetooth 4.0 (or less than 4.0)
This quick guide outlines the steps you should follow to enroll your
appliance using the App Hoover Wizard, utilizing a device without
Bluetooth technology. We recommend you to proceed with a
smartphone/tablet equipped with this technology to make the
procedure simpler.
STEP 1
·Make a note of the appliance Serial Number and Wi-Fi Name and
Password (WPA/WEP Key), which are normally found on the back
of your Wi-Fi router.
·Please make sure that your smartphone/ tablet is connected to
the same Wi-Fi network.
NOTES
- The frequency of the home Wi-Fi network has to be set on the 2.4
GHz band. You can not configure the appliance if your home
network is set to the 5 GHz band.
-If you are having trouble locating the WPA/WEP Password,
please contact your Internet Provider.
STEP 2
· Download the Hoover Wizard App from the Store.
· Open the Hoover Wizard App and create your user profile by
taping on "Register". Accept the privacy policy and fill in the
required fields.
NOTES
- The App is available for Android (version 4.4 or higher) and iOS
(version 8.0 or higher) devices.
- If you already have a Hoover Wizard user profile, you can login
using your credentials.
STEP 3
· In the homepage, tap on the icon with the three bars on the top left
to enter your profile, then tap on "REGISTER NEW APPLIANCE"
and select the name of the product that you want to enroll.
STEP 4
· Insert the purchase date of your appliance (DD/MM/YYYY), then
tap on "Proceed".
· Insert the 16 digits of the serial number or scan the QR code on
the appliance. Tap on "Next". Check data correctness and tap on
"Confirm". Once the system has recognized the product, tap on
"Next".
STEP 5
1) Tap on the icon ONE-FI.
2) Set the oven on ONE-FI RESET (the oven will beep) and wait 5
min.
3) The WIFI icon will blink.
·In App - Tap on "Confirm".
NOTES
- Enrollment must be completed within 5 minutes.
- To ensure correct data transfer, we recommend that you stay with
the device close to the appliance.
EN 13