5.1 Channel Surround Hookups - Sony DVP-S9000ES Operating Instructions Manual

5.1 Channel Surround Hookups

With DVDs which contain DTS, Dolby Digital or MPEG
audio sound, you can enjoy the surround sound while
producing the effect of being in a movie theater or a
concert hall using a digital component with a built-in
DTS, MPEG audio or Dolby Digital decoder (not
supplied). The player outputs the surround sound signals
from the DIGITAL OUT OPTICAL and COAXIAL
connectors.
Using a receiver (amplifier) having the OPTICAL or
COAXIAL connector and 6 speakers, you can enjoy even
greater real audio presence in the comfort of your own
home.
Required cords
Optical digital connecting cord* (not supplied) (1)
Coaxial digital (75 ) connecting cord* (not supplied) (1)
S video cord (supplied) (1)
* Connect the component via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord (not supplied). You do not need to connect
both of these cords. See the figure on the next page.
Do not connect the mains lead to a switched mains such
as the mains on a receiver (amplifier). Doing so may cause
the Playback Memory, Disc Memo and menu settings to be
cancelled when you turn off the receiver.
Notes
• Do not connect the power cord to a mains or press the POWER
switch before completing all connections.
• Refer to the instructions supplied with the component to be
connected.
• The cord connectors should be fully inserted into the jacks. A
loose connection may cause hum and noise.
• SACD audio signals are not output from the DIGITAL OUT
OPTICAL or COAXIAL connectors.
16
Setups for the player
Some setup adjustments are necessary for the player
depending on the components to be connected.
Use the setup display to change the various settings.
For details on using the setup display, see page 52.
• When you connect an audio component with a built-
in Dolby Digital decoder A
Set "DIGITAL OUT" in "AUDIO SETUP" to "ON" and
then set "DOLBY DIGITAL" to "DOLBY DIGITAL" in
the setup display. (page 63, 64)
• When you connect an audio component with a built-
in MPEG audio decoder B
Set "DIGITAL OUT" in "AUDIO SETUP" to "ON" and
then set "MPEG" to "MPEG" in the setup display. (page
63, 64)
• When you connect an audio component with a built-
in DTS decoder C
Set "DIGITAL OUT" in "AUDIO SETUP" to "ON" and
then set "DTS" to "ON" in the setup display. (page 63,
64)
• When you connect an audio component that accept
the 96kHz/24bit audio signal D
Set "DIGITAL OUT" in "AUDIO SETUP" to "ON" and
then set "48kHz/96kHz PCM" to "96kHz/24bit" in the
setup display. (page 63, 64)
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
AUDIO FILTER
DOWNMIX DOLBY SURROUND
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
DTS:
48kHz/96kHz PCM:
To set, press , then
ENTER
To quit, press .
DISPLAY
Notes
• When you do not connect an audio component with a
built-in Dolby Digital decoder, do not set "DOLBY DIGITAL"
to "DOLBY DIGITAL."
• When you do not connect an audio component with a
built-in MPEG audio decoder, do not set "MPEG" to
"MPEG."
• When you do not connect an audio component with a
built-in DTS decoder, do not set "DTS" to "ON."
• When you do not connect an audio component that cannot
accept the 96kHz/24bit audio signal, do not set "48kHz/
96kHz PCM" to "96kHz/24bit."
OFF
STANDARD
SHARP
ON
DOLBY DIGITAL
MPEG
ON
96kHz/24bit
.