Table of Contents
Advertisement
Quick Links
Contents
1 Preparing for installation ·········································································· 1-1
Safety recommendations ································································································································ 1-1
Site preparation ··············································································································································· 1-1
Installation accessories ··································································································································· 1-2
Installation tools ·············································································································································· 1-2
2 Installing the AP ······················································································· 2-1
Installation flowchart········································································································································ 2-1
Pre-installation tasks ······································································································································· 2-1
Determining the installation position ··············································································································· 2-1
Mounting the AP·············································································································································· 2-2
Mounting the AP on a wall ······················································································································ 2-2
Mounting the AP on a ceiling ·················································································································· 2-4
(Optional) Removing the AP ··························································································································· 2-6
Connecting the AP to a power source ············································································································ 2-6
Connecting a PoE power source ············································································································· 2-6
Connecting a local power source ············································································································ 2-7
Connecting a power injector ···················································································································· 2-7
Check after power-on ······························································································································ 2-8
Connecting the AP to the network··················································································································· 2-8
3 Appendix A Technical specifications ························································ 3-1
4 Appendix B Ports and LEDs ···································································· 4-1
Ports ································································································································································ 4-1
LEDs ······························································································································································· 4-2
i
Advertisement
Table of Contents
Related Manuals for H3C WA6638
Summary of Contents for H3C WA6638
-
Page 1: Table Of Contents
Contents 1 Preparing for installation ·········································································· 1-1 Safety recommendations ································································································································ 1-1 Site preparation ··············································································································································· 1-1 Installation accessories ··································································································································· 1-2 Installation tools ·············································································································································· 1-2 2 Installing the AP ······················································································· 2-1 Installation flowchart········································································································································ 2-1 Pre-installation tasks ······································································································································· 2-1 Determining the installation position ··············································································································· 2-1 Mounting the AP··············································································································································... -
Page 2: Preparing For Installation
Preparing for installation Safety recommendations WARNING! Only professional technical engineers are allowed to install and remove the AP and its accessories. Read the safety instructions for the AP carefully before installing or servicing it. To avoid possible bodily injury and equipment damage, read the following safety recommendations before installing the AP. -
Page 3: Installation Accessories
Installation accessories Figure 1-1 Accessories provided with the AP Installation tools When installing the AP, you might need the following tools. Prepare the installation tools as required. Figure 1-2 Installation tools... -
Page 4: Installing The Ap
Installing the AP Installation flowchart Figure 2-1 Installation flowchart Start Complete pre-installation tasks Determine the mounting option Wall mounting Ceiling mounting Install the AP Connect the AP to the power source Connect the AP to the network Pre-installation tasks Before installing the AP, perform the following tasks: •... -
Page 5: Mounting The Ap
Mounting the AP The AP can be installed only indoors. You can mount the AP on a wall or a ceiling. Mounting the AP on a wall Place the mounting bracket against the wall and mark the installation holes on the wall. Figure 2-2 Marking the installation holes on the wall Drill holes with a diameter of 6 mm (0.24 in) and a depth of 30 mm (1.18 in) at the marked locations, as shown in... - Page 6 Insert the screws through the installation holes in the mounting bracket into the holes in the wall. Fasten the screws to secure the mounting bracket to the wall, as shown in Figure 2-5. Figure 2-5 Attaching the mounting bracket to the wall Feed cables through the cable holder, connect the cables to the AP, and then attach the cable cover to the AP, as shown in Figure...
-
Page 7: Mounting The Ap On A Ceiling
Figure 2-7 Attaching the AP to the mounting bracket Mounting the AP on a ceiling CAUTION: The ceiling for installing the AP must be less than 18 mm (0.71 in) in thickness, and can bear a load of 5 kg (11.02 lb). If you must install the AP on a ceiling not strong enough, use boards to reinforce the ceiling. - Page 8 Figure 2-9 Attaching the mounting bracket to the ceiling Feed cables through the cable holder, connect the cables to the AP, and then attach the cable cover to the AP. Position the three screws on the AP into the keyhole slots in the mounting bracket, as shown in Figure 2-10.
-
Page 9: (Optional) Removing The Ap
(Optional) Removing the AP Insert a stick-like tool with a diameter less than 5.7 mm (0.22 in) into the lock hole of the mounting bracket until you hear a click. Then slide the AP in the direction of the UP arrow and disengage the screws from the keyhole slots to remove the AP. -
Page 10: Connecting A Local Power Source
CAUTION: The AP is to be connected only to PoE networks without routing to the outside plant. As a best practice, use the H3C ADP040-54V-PoE-GL power injector. The power injector must be ordered separately. To power the AP by using a power injector: Connect the signal input port on the power injector to an Ethernet switch and the signal and power output port to the AP. -
Page 11: Check After Power-On
AP information State : I = Idle, J = Join, JA = JoinAck, IL = ImageLoad C = Config, DC = DataCheck, R = Run, M = Master, B = Backup AP name APID State Model Serial ID WA6638 219801A24F8191E00166... -
Page 12: Appendix A Technical Specifications
Appendix A Technical specifications Table 3-1 Technical specifications Item Specification Dimensions (H × W × D) (without the 52 × 236 × 236 mm (2.05 × 9.29 × 9.29 in) mounting bracket) Weight 1300 g (45.86 oz) • ≤ 25 W (not supplying PoE power) System power consumption •... -
Page 13: Appendix B Ports And Leds
Appendix B Ports and LEDs Ports The AP provides the following ports: • One console port • One USB port • One 100/1000/2500/5000/10000M Ethernet copper port • One 10/100/1000M Ethernet copper port • One power port The AP also has a reset button and a security slot. The security slot is 7 × 3 mm (0.28 × 0.12 in) in size. -
Page 14: Leds
Standards and Port Description protocols Used for connecting a downlink device. It can • IEEE802.3 also supply PoE power to the downlink device. 10/100/1000M Ethernet • IEEE802.3u It is represented by interface number GE1/0/1 in copper port (GE/PSE) • the MAP file and GigabitEthernet 1 for IEEE802.3af configuration on the AC.