Table of Contents
Advertisement
Available languages
Available languages
EngLIsh
Attaching the Dust Extraction System to the
Tool (Fig. A, F)
1. Slide the assembled dust extraction system onto the nose
of the tool through the ring opening
and sleeve and onto the tool's collar
needed, refer to Attaching the Ring Adapter.
2. Rotate the dust extraction system to the desired position on
the tool.
3. Lock the assembly in place by securely tightening the side
handle
1
, rotating the grip clockwise so that the assembly
will not rotate.
4. Install and adjust the depth adjustment rod
desired length.
FITMENT GUIDE
No adaptor collar needed
Toothed adaptor needed
Smooth adaptor needed
Attaching and Removing the Bellows
(Fig. A, G)
Your dust extraction system comes with a short bellow
. Refer to Technical Data for proper usage for
a long bellow
5
each bellow.
Attaching the Bellow
You can attach the bellow with the bit either installed
or removed.
1. Push the bellow onto the end of the dust extraction
connection port while using a twisting motion until the
bellow is secure.
2. Place the wear ring
4
on the oppposite end of the bellow,
closest to the work piece.
Removing the Bellow
To remove the bellow, twist and pull the bellow away from the
dust extraction unit.
Attaching a Dust Extractor to the Dust
Extraction Assembly (Fig. H–J)
1. Insert the dust hose
8
into the dust extraction connection
port
7
and a dust extractor (Fig. H).
nOtE: The dust extraction system is compatible with
or without a dust extractor. The tool can be used with
the plug
11
inserted in the dust extraction connection
port
7
(Fig. I). If you are using the plug, it is recommended
you remove the dust from the bellow after drilling each hole.
14
2
, past the tool holder
18
. If a ring adaptor is
6
to
54 mm collar
43 mm collar
48 mm collar
10
and
AirLock Compatible (Fig. A, H–J)
Your D
WALT dust extractor is compatible with the D
e
AirLock connection system. The AirLock allows for a fast, secure
connection between the dust extraction system and dust
extractor. The AirLock connector
to D
WALT compatible tools or through the use of an AirLock
e
adaptor
(available from your local D
20
nOtE: If using an AirLock adaptor
attached to the tool outlet before following the steps below.
1. Ensure the collar on the AirLock connector is in the unlock
position. (Refer to Figure J.) Align notches
AirLock connector as shown for unlock and lock positions.
2. Push the AirLock connector onto the dust extraction system
hose
8
.
3. Rotate the collar to the locked position.
nOtE: The ball bearings inside collar lock into the slot and
secure the connection. The dust extraction system is now
securely connected to the dust extractor.
Removing the Dust Extraction System from
the Tool (Fig. A, I)
1. Remove the dust hose
8
or the dust port plug
dust extraction connection port
2. Remove the bit from the tool holder.
3. Turn side handle
to loosen and slide from the nose of
1
the tool.
4. If a ring adaptor was used, open and remove the adaptor
from the nose of the tool.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start‑up
can cause injury.
Proper Hand Position (Fig. K)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
of the hammer and one hand on the side handle
extraction system.
MAINTENANCE
Your D
WALT dust extraction system has been designed
e
to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
WALT
e
19
(Fig. J) connects directly
WALT supplier).
e
20
, ensure it is firmly
21
on collar and
11
from the
7
.
12
1
of the dust
Advertisement
Table of Contents
