Related Manuals for Crestron TSS-770
Summary of Contents for Crestron TSS-770
- Page 1 TSS-770 and TSS-1070 7 in. and 10.1 in. Room Scheduling Touch Screens Product Manual Crestron Electronics, Inc.
- Page 2 United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
-
Page 3: Table Of Contents
Contents Introduction Access the Setup Screens Local Configuration Ethernet Setup Application Selection Wi-Fi Setup Select a Wi-Fi Access Point Manage Wi-Fi Access Points Bluetooth Beacon Virtual Toolbar Diagnostics & Advanced Test Patterns Touch Test LAN Test Wi-Fi Test About Web Configuration Actions Menu Reboot Restore Update Firmware Download Logs... - Page 4 Network Proxy Settings Device Pairing Audio Auto Update Cloud Settings Applications Security Authentication 802.1x Configuration Application Selection Connect to XiO Cloud Service ii • Contents Product Manual — Doc. 8745C...
-
Page 5: Introduction
NOTE: The TSS-770 and TSS-1070 are functionally similar. For simplicity within this guide, the term "touch screen" is used except where otherwise noted. -
Page 6: Access The Setup Screens
To access the touch screen's built-in setup screens during regular operation, place five fingers on the display and hold for 15 seconds. The main Setup screen is displayed (TSS-770 shown). TSS-770 Setup Screen NOTE: The touch screen also provides a web configuration interface that may be used to view and configure various touch screen settings. -
Page 7: Local Configuration
If DHCP is turned off, tap Set Static IP Address Settings to enter static IP addresses manually. Tap Set Hostname to enter a new touch screen hostname using an on-screen keyboard. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 3... - Page 8 To edit the static IP address, the static subnet mask, the static default router, the preferred DNS, or the alternate preferred DNS, tap the text field underneath the setting name. 4 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 9 Tap REBOOT to exit setup mode and reboot the touch screen. Tap < BACK to return to the Ethernet Setup screen. Tap < BACK on the Ethernet Setup screen to return to the Setup screen. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 5...
-
Page 10: Application Selection
Each application uses a unique setup procedure for registering and configuring the application. For more information on setting up each application, refer to Application Selection page 58). Tap < BACK to return to the Setup screen. 6 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... -
Page 11: Wi-Fi Setup
Tap APPLY CHANGES to apply any new Wi-Fi settings to the touch screen and to stay in setup mode. Tap REBOOT to exit setup mode and reboot the touch screen. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 7... - Page 12 To edit the static IP address, the static subnet mask, the static default router, the preferred DNS, or the alternate preferred DNS, tap the text field underneath the setting name. The on-screen numeric keypad opens for the chosen setting. Edit IP Address On-Screen Numeric Keypad 8 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
-
Page 13: Select A Wi-Fi Access Point
Use the Connect to a Wi-Fi Access Point (1-2-3) screen to connect the touch screen to an existing WAP that is in range or to configure a new WAP. Any WAPs that are in range and discoverable are displayed under Step 1 - Select a WAP upon successful discovery. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 9... - Page 14 7. Enter the password used to connect to the WAP, and then tap SAVE. 8. Tap Step 3 - Make this my Access Point. The Wi-Fi WAP Selection screen is displayed. 10 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 15 WAP may be deleted, or tap < BACK to cancel adding the new WAP. For more information, refer to Manage Wi-Fi Access Points (on the next page). Tap < BACK to return to the Wi-Fi Setup screen. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 11...
-
Page 16: Manage Wi-Fi Access Points
Tap Delete this Access Point to delete the selected WAP. If a WAP is deleted, it must be added back to the list using the procedures described in Select a Wi-Fi Access Point (on page 9). Tap < BACK to return to the Wi-Fi Setup screen. 12 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... -
Page 17: Bluetooth Beacon
Use the BLE Beacon screen to configure the built-in PinPoint™ proximity detection beacon. Using Bluetooth® technology, the beacon works with the Crestron App or Crestron PinPoint App to determine when a mobile device is in or near the same room as the beacon, and signals the mobile app to automatically display the appropriate controls and information for the room. -
Page 18: Virtual Toolbar
The toolbar is hidden automatically after a set timeout duration. NOTE: Virtual button functionality can be custom programmed using a Crestron control system. 14 • TSS-770 and TSS-1070... - Page 19 Tap Toolbar Buttons to display a screen for showing or hiding individual buttons in the virtual toolbar. Tap On or Off next to a button to show or hide the button, respectively. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 15...
- Page 20 On-screen Toolbar Screen - Toolbar Buttons Tap < BACK to return to the Setup screen. 16 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
-
Page 21: Diagnostics & Advanced
Use the Diagnostics & Advanced screen to access various diagnostic test screens for the touch screen. The Diagnostics & Advanced screen also provides the touch screen CPU temperature and available memory. Each test screen is described in the sections that follow. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 17... -
Page 22: Test Patterns
Use the Test Pattern Diagnostics screen to display any of the available test patterns. Tap one of the buttons on the screen to display its respective test pattern. Tap < BACK to return to the Diagnostics & Advanced screen. 18 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... -
Page 23: Touch Test
Use the touch test screen to test the touch functionality of the display. When a location button is tapped, its respective indicator lights on the screen. Tap RETURN to return to the Diagnostics & Advanced screen. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 19... -
Page 24: Lan Test
The connection data updates after every successive ping. Tap < BACK to return to the Diagnostics & Advanced screen. 20 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... -
Page 25: Wi-Fi Test
The connection data updates after every successive ping. Tap < BACK to return to the Diagnostics & Advanced screen. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 21... -
Page 26: About
NOTE: The Check For App Updates button is shown only if an application is running on the touch screen. Tap RESTORE at the top right of the screen to restore the touch screen to its default factory settings. Tap < BACK to return to the Setup screen. 22 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... -
Page 27: Web Configuration
This interface is also accessible using the XiO Cloud® service. To access the configuration interface: 1. Use the Device Discovery tool in Crestron Toolbox™ software to discover the touch screen and its IP address on the network. -
Page 28: Actions Menu
Some device settings may be displayed or hidden depending on the selected application mode. If the Crestron room scheduling application is running on the touch screen, the web configuration utility provides additional configuration options for the room scheduling application. For more information, refer to the Crestron Room Scheduling Panels Operations Guide (Doc. -
Page 29: Restore
Manage Certificates Click Manage Certificates to manage any certificates that are installed on the touch screen. For more information on certificate management, refer to 802.1x Configuration (on page 55). Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 25... -
Page 30: Enter Setup
Project Upload dialog box opens. Project Upload Dialog Box NOTE: This selection is available only if the touch screen is running in Crestron Default scheduling mode. To upload a custom scheduling project: 1. Click Browse, and then navigate to the project .vtz file on the host computer. -
Page 31: App Upgrade
Click App Upgrade to update the currently selected application. The update progress is shown in a pop-up window. Once the update is complete, click OK to close the pop-up window. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 27... -
Page 32: Status
Click + More details at the bottom of the Device tab to display an expanded section that shows additional touch screen information. If + More Details is selected, click - Less details to collapse the section. 28 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... -
Page 33: Network
Subnet Mask: The touch screen subnet mask address, shown only if an Ethernet connection is enabled Default Gateway: The gateway router address, shown only if an Ethernet connection is enabled Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 29... -
Page 34: Usb
Click USB to view the status of a connected USB accessory, such as a room scheduling hallway sign or light bar. Status Tab - USB The following USB information is displayed: Accessory Connected: The name of the connected accessory Accessory Type: The type of connected accessory 30 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... -
Page 35: Room Scheduling
Room Status: The status of the connected room (available or reserved) Calendar Sync: The status of the sync between the touch screen and the room scheduling calendar Crestron Fusion Online Status: The status of the Crestron Fusion connection (if applicable) Display Click Display to view the display status. -
Page 36: Settings
Red text is displayed next a setting to indicate an invalid value. System Setup Click System Settings to configure general network and touch screen settings. Settings Tab - System Setup 32 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... - Page 37 If an authentication method is selected, enter the ID for the key used to authenticate against the SNTP server into the Key ID text field. To remove an entry, fill the checkbox to the left of the table entry, and then click Delete. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 33...
- Page 38 Date Format: Select the format that the date will display on the touch screen using the drop-down menu. Time: Select the time for the touch screen (in 24-hour format) using the pop-up menu that is displayed. 34 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 39 Settings Tab - System Setup (Network) NOTE: The IP Address, Subnet Mask, and Default Gateway fields are required only if DHCP is set to Disabled for Ethernet and Wi-Fi network connection. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 35...
- Page 40 Click Add to add a new entry to the Wi-Fi access point table. After selecting one more entries in the Wi-Fi access point table, click Remove to delete the selected entries. 36 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 41 Click the + (plus) icon next to Device Display to display the following device display settings. Settings Tab - System Setup (Device Display) Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 37...
- Page 42 Text Font Face: Use the drop-down menu to select a font for the screensaver text. 38 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 43 Video URL: Enter a URL of video to be used by the touch screen screensaver. Logo Setting: Select one of the radio buttons (None, Crestron, and Custom) to select a logo type to use on the touch screen screensaver. Logo URL: If Logo Setting is set to Custom, enter a URL of a custom logo to be used by the touch screen screensaver.
-
Page 44: Services
Cloud server. This connection is only applicable when the scheduling mode is set to Crestron Default or User Project. Crestron Fusion Cloud URL: Enter the URL used to connect the touch screen to the desired Crestron Fusion Cloud server. 40 • TSS-770 and TSS-1070... -
Page 45: Network Proxy Settings
HTTPS Proxy Port: Enter the port number of the HTTPS proxy server. Username: Enter the username required for the HTTPS proxy server. Password: Enter the password required for the HTTPS proxy server. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 41... -
Page 46: Device Pairing
Device Authentication: Enter authentication credentials for the CEN-ODT-C-POE (if required): Device Username: Enter a valid username used to access the device. Device Password: Enter a valid password used to access the device. 42 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... -
Page 47: Audio
Media Volume: Enter a value (1‒100) for the touch screen media volume level. Beep Enabled: Turn on the toggle to mute the touch screen beep volume. Beep Volume: Enter a value (1‒100) for the touch screen beep volume. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 43... -
Page 48: Auto Update
Custom URL: Turn on the toggle use a custom update server URL. If turned off, the server URL will default to the standard Crestron update sever. Custom URL Path: If Custom URL Path is turned on, enter the custom URL path for the update server. -
Page 49: Applications
Application Selection (on page 58). Security Click the Security tab on the top left of the configuration interface to display selections for configuring security and authentication settings for the touch screen. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 45... -
Page 50: Authentication
Use the following Authentication Management settings to add, delete, and edit touch screen users and groups. Current User Click the Current User tab to view and edit information for the current touch screen user. Authentication Management - Current User Tab 46 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C... - Page 51 Enter the existing password in the Current Password field. Then, enter a new password in the Password field, and reenter the password in the Confirm Password field. Click OK to save the new password, or click Cancel to cancel the change. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 47...
- Page 52 Additionally, the number of users displayed on each page may be set to 5, 10, or 20 users. An Actions column is also provided for each user that allows various actions to be performed. The following selections may be selected from the Actions column. 48 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 53 Click OK to return to the Authentication Management > Users page. Update User Click the editing button in the Actions column to edit settings for the selected user. The Update User dialog box is displayed. Update User Dialog Box Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 49...
- Page 54 Actions column to delete the user. A pop-up dialog box is displayed asking whether the user should be deleted. Click Yes to delete the user or No to cancel deleting the user. 50 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 55 A user must be added to an Active Directory group to be selected as an Active Directory user. Click OK to save any changes and to return to the Authentication Management > Users page. Click Cancel to cancel creating a new user. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 51...
- Page 56 Additionally, the number of groups displayed on each page may be set to 5, 10, or 20 users. An Actions column is also provided for each group that allows various actions to be performed. The following selections may be selected from the Actions column. 52 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 57 Active Directory group in the Name field. If this information is being entered via console commands, omit domain\local from the command (for example, adddomaing - n:crestron -L:A instead of adddomaing -n:domain.local\crestron -L:A). Access Level: The access level of the group and its users...
- Page 58 Active Directory Group: Turn on the toggle to use authentication via Active Directory for the group. Click OK to save any changes and to return to the Authentication Management > Groups page. Click Cancel to cancel creating a new group. 54 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
-
Page 59: 802.1X Configuration
CAs as trusted CAs. Select Manage Certificates from the Action menu to add or remove CAs from the list. The Manage Certificates dialog box is displayed with the Root tab selected. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 55... - Page 60 Click Add [Type] Certificate to add a CA of one of the four available types (Root, Intermediate, Machine, or Web Server) to the list of CAs. The Add Certificate pop-up dialog box is displayed. Add Certificate Dialog Box 56 • TSS-770 and TSS-1070 Product Manual — Doc. 8745C...
- Page 61 Clicking the x button before the CA file is uploaded to the touch screen cancels the upload. Click the x button to close the Manage Certificates dialog box and to return to the 802.1x Authentication page. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 57...
-
Page 62: Application Selection
Support for additional applications will be provided by future firmware updates. The touch screen runs only one app, which is selected at setup. Only the apps approved and delivered by Crestron may run on the touch screen. NOTE: Additional subscriptions and/or licenses may be required. Refer to each provider’s website for details about the capabilities and requirements of its scheduling application and services. - Page 63 For more information on using and setting up each application, refer to the provider's website. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 59...
-
Page 64: Connect To Xio Cloud Service
XiO Cloud® service allows supported devices across an enterprise to be managed and configured from one central and secure location in the cloud. Supported Crestron® devices are configured to connect to the service out of the box. Use of the service requires a registered XiO Cloud account. To register for an XiO Cloud account, refer to www.crestron.com/Support/Tools/Licensing-Registration/XiO-Cloud-Registration-... - Page 65 This page is intentionally left blank. Product Manual — Doc. 8745C TSS-770 and TSS-1070 • 61...
- Page 66 Product Manual — Doc. 8745C Crestron Electronics, Inc. 15 Volvo Drive, Rockleigh, NJ 07647 07/15/21 Tel: 888.CRESTRON Specifications subject to Fax: 201.767.7656 change without notice. www.crestron.com...