Life Fitness Axiom Series Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Life Fitness Manuals
  4. Fitness Equipment
  5. Axiom Series
  6. Assembly instructions manual

Life Fitness Axiom Series Assembly Instructions Manual

Abdominal / back extension
Hide thumbs Also See for Axiom Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Axiom Series Abdominal / Back
Extension
OP-ABBA
Assembly Instructions
1015208-0001 REV AA

Advertisement

Table of Contents
loading

Related Manuals for Life Fitness Axiom Series

Summary of Contents for Life Fitness Axiom Series

  • Page 1 Axiom Series Abdominal / Back Extension OP-ABBA Assembly Instructions 1015208-0001 REV AA...
  • Page 3 Latin America and Caribbean* Spain Hong Kong Life Fitness, LLC Life Fitness IBERIA Life Fitness Asia Pacific LTD Columbia Centre III C/Frederic Mompou 5,1º1ª 32/F, Global Trade Square 9525 Bryn Mawr Avenue 08960 Sant Just Desvern Barcelona 21 Wong Chuk Hang Road Rosemont, IL 60018 U.S.A.
  • Page 4 User and Service Documents Link https://www.lftechsupport.com/web/document-library/documents Additional information is available online using the link above. ‫أ علاه‬ ‫إل ر إبط‬ ‫باستخدإم‬ ‫إ لإ ن تر نت‬ ‫على‬ ‫إضافية‬ ‫معلومات‬ ‫تتوفر‬ 点击上面的链接可在线获取更多信息。 Flere oplysninger er tilgængelige online gennem linket ovenfor. Bijkomende informatie is online beschikbaar via bovenstaande link. Vous trouverez plus d'informations en ligne à...

  • Page 5: Table Of Contents

    2XL Corporation. PureGreen 24 is a trademark of Pure Green. © Copyright 2020, Life Fitness, LLC. All Rights Reserved. Life Fitness, Hammer Strength, Cybex, ICG and SCIFIT are registered trademarks of Life Fitness, LLC and its affiliated companies and subsidiaries. Brunswick and related trademarks used under license from Brunswick Corporation.

  • Page 6: Safety Information

    • DO NOT use or permit use of any equipment that is damaged and/or has worn or broken parts. For all Life Fitness Family of Brands equipment, use only replacement parts supplied by Life Fitness Family of Brands.
  • Page 7 Life Fitness Family of Brands will provide service and maintenance training at our corporate facility upon request or in the field if proper arrangements are made. • Before use, examine all accessories approved for use with the Life Fitness Family of Brands equipment for damage or wear.

  • Page 8: Product Labels

    Product Labels General Warning Serial Number Page 6 of 38...

  • Page 9: Label Locations

    Label Locations Item Description Qty. General Warning Serial Number Page 7 of 38...

  • Page 10: Assembly

    2. Assembly Component and Hardware List OP-ABBA Tower Components Item Description Qty. Tower Frame Guide Rod Increment Weight Guide Rod Rear Shroud Label, Weight Stack Tube Cap Top Cap OP-ABBA Tower Hardware Kit Item Description Qty. Tower Hardware Kit, OP-ABBA Hole Plug, 8.7 mm Hole Plug, ½"...
  • Page 11 OP-ABBA Tower Hardware Kit Optional: Front Shroud Kit Components Item Description Qty. Front Shroud, Left Front Shroud, Right Bottom Cap Optional: Front Shroud Kit Hardware Kit Item Description Qty. Front Shroud Hardware Kit Screw, M4.2 x 0.7, Phillips Screw, M10 x 1.5, 20mm Washer, Flat 3/8"...
  • Page 12 OP-ABBA Components Item Description Qty. Main Frame Assembly Base Frame Assembly Cross Brace Lower Pulley Assembly Pivot Shaft Input Arm Assembly with Pulleys Detent Arm Assembly Input Arm Assembly Handle Arm Assembly Retaining Plate Seat Pad Lumbar Pad Cable Front Cap Head Plate Assembly Increment Weight Assembly Multilingual Label Sheet...

  • Page 13: Tools Required

    Item Description Qty. Hole Plug, 1" Spacer, .403" Spacer, .653" Shim Tools Required • 7/16" Wrench • 10 mm Wrench • 17 mm Wrench • 7 mm Allen wrench • 8 mm Allen wrench • 10 mm Socket wrench • 10 mm Ratchet wrench •...

  • Page 14: Assembly Procedure

    Assembly Procedure Two people will be required for this procedure. TIP: Read and understand all instructions thoroughly before assembling this unit. Check all items carefully. If there is damage, see the Customer Service section of this manual for proper procedure to return, replace, or reorder parts. Assemble Frame Components 1.
  • Page 15 4. Install screws, washers, and locknuts securing the main frame assembly to the base frame assembly and cross brace using an 8mm Allen wrench and a 17mm wrench. Item Description Qty. Main Frame Assembly Base Frame Assembly Cross Brace Screw, M10 x 1.5, 120mm Washer, Flat 3/8"...
  • Page 16 2. Slide increment weight guide rods through the top of the tower frame and down through the clips in the increment weight. Place increment weight guide rods into holes at the bottom plate of the tower frame. Item Description Qty. Increment Weight Guide Rod Increment Weight 3.
  • Page 17 5. Route cable up through the top of the tower frame and down through the side tube of the frame. Item Description Qty. Cable 6. Install screws, washers, spacers, and nuts securing the pulleys to the top of the tower frame using an 8mm Allen wrench and 17mm wrench.
  • Page 18 8. Starting at the top, press the shroud retainers into the rear shroud securing it to the tower frame. Item Description Qty. Shroud Retainer Rear Shroud 9. NOTE: OPTIONAL: If your product does not include front shrouds, skip this step. Install screws and washers securing the bottom cap to the bottom of the tower frame using an 8mm Allen wrench.
  • Page 19 11. NOTE: OPTIONAL: If your product does not include front shrouds, skip this step. Install screws and shroud retainer grommets into the side tubes of the tower frame using a Phillips screwdriver. Item Description Qty. Grommet, Shroud Retainer Screw, M4.2 x 0.7, Phillips Tighten hardware to 10-13 in-lb (1.1-1.5 Nm).

  • Page 20: Item Description Qty

    14. Place guide rods with weight stack cushions into the holes at the bottom of the tower frame. Item Description Qty. Guide Rod Weight Stack Cushion 15. Lean guide rods outwards and slide weight stack down guide rods onto weight stack cushions. Slide head plate assembly down guide rods and onto weight stack.

  • Page 21: Guide Rod

    16. Tip guide rods back into an upright position in the tower frame. Compress guide rod housings onto the springs and guide rods and fit up into the top of the tower frame. Item Description Qty. Guide Rod Housing Spring Guide Rod 17.

  • Page 22: Weight Stack

    18. Thread cable end through the jam nut and into the head plate bayonet. See Cable Handling Guide for details. Item Description Qty. Cable Nut, M16 Hex Jam Head Plate Bayonet NOTE: Check proper thread engagement. To do so, attempt to pass a 7mm Allen wrench through the portal in the head plate bayonet.
  • Page 23 22. Slide the carriage bolt to the end of the slot in the lower pulley assembly using a 17mm wrench. Item Description Qty. Carriage Bolt, M10 x 1.5, 50mm Tighten hardware to 20-25 ft-lb (27.1-33.9 Nm). 23. Install screws and washers securing the lower pulley assembly to the tower frame using an 8mm Allen wrench. Item Description Qty.
  • Page 24 Install Work Arm Assembly 1. Slide .653" spacers and input arm assembly with pulleys onto the pivot shaft. Item Description Qty. Input Arm Assembly with Pulleys Pivot Shaft Spacer, .653" 2. Slide detent arm assembly and .653" spacer onto the pivot shaft. Item Description Qty.
  • Page 25 4. Slide handle arm assembly and .403" spacer onto the pivot shaft. Item Description Qty. Handle Arm Assembly Spacer, .403" 5. Wrap bungee cord around the work arm assembly to hold the arm assemblies together. Item Description Qty. Bungee Cord Page 23 of 38...
  • Page 26 6. Place work arm assembly into the grooves on the base frame assembly. Item Description Qty. Work Arm Assembly Base Frame Assembly NOTE: Position the pivot shaft so that the flat side is facing down before lowering the work arm assembly into the base frame assembly.
  • Page 27 9. Repeat Steps 7 and 8 to install the retaining plate and hardware to the other side of the pivot shaft. Cable Routing 1. Route cable through pulley brackets on the base frame assembly and up through the pulley bracket on the input arm assembly with pulleys.
  • Page 28 Install/Remove Optional Shims The objective of installing/removing shims is to get the detent arm assembly as close to vertical as possible, to remove play between the input arm assembly with pulleys and detent arm assembly, and to remove play between the input arm assembly and detent arm assembly.
  • Page 29 3. To bring the input arm assembly and detent arm assembly closer or bring the detent arm assembly towards the rear of the machine: a. Lean the input arm assembly towards the front of the machine. b. Remove screws and washers securing the bumper to the base frame assembly using a Torx screwdriver. Item Description Qty.
  • Page 30 Install Front and Top Caps 1. NOTE: OPTIONAL: If your product does not include front shrouds, skip this step. Set front shrouds into the bottom cap. Install screws securing the front cap to the tower frame using a 10 mm wrench.
  • Page 31 4. Install screws securing the tube caps to the tower frame using a Phillips screwdriver. Item Description Qty. Top Cap Tube Cap Screw, 8 x ¾" Phillips Grommet Tighten hardware to 10-13 in-lb (1.1-1.5 Nm). 5. Press top cap down into the holes at the top of the tower frame. 6.
  • Page 32 3. Install screws and washers securing the lumbar pad to the main frame assembly using an 8mm Allen wrench. Item Description Qty. Lumbar Pad Screw, M10 x 1.5, 35mm Washer, Flat 3/8" Tighten hardware to 40-50 in-lb (4.5-5.6 Nm). Test Unit For Proper Operation. Page 30 of 38...

  • Page 33: Product Information

    3. Product Information Specifications Machine Weight: 519 lbs. 235 kg. Size (L x W x H): in. = 58 x 45 x 53 cm = 147 x 114 x 135 Live Area (L x W x H): in. = 94 x 69 x 77 cm = 239 x 175 x 196 Max User Weight: 300 lbs.

  • Page 34: Cable Handling Guide

    WARNING: Use of non certified “techs” note: Service warranties may be void if a non-Life Fitness-certified technician performs service work. Replacement of any strength cables should be performed by a Life Fitness certified technician.

  • Page 35: Tensioning Cable

    Tensioning Cable Cable should have enough tension so it stays seated into the pulley but not so tight that it pulls the head plate off the weight plate below it. 1. If the head plate has lifted, loosen the jam nuts at the terminations and loosen the threaded plugs a half turn until the head plate comes to rest on the weight plate below.

  • Page 36: Strength Cable Wear Guide

    Strength Cable Wear Guide Replace cable at first sign of any of the following: FRACTURES: Casing can crack or fracture under strains during use. Any crack in the casing merits cable replacement even if no wire rope is exposed. Be especially observant for fractures near the components on the cable assembly - IE.

  • Page 37: Bolt To Floor Guide Introduction

    5. Bolt to Floor Guide Introduction Life Fitness designs its products to be stable when used as designed. Because strength training is dynamic, we cannot predict how users will ultimately use the products in all circumstances. Therefore, Life Fitness recommends that strength training equipment be secured to a solid, level surface to stabilize and eliminate rocking or tipping over.

  • Page 38: Anchor Specifications

    3000psi (20 N/mm2) beyond anchor length Pullout Force Life Fitness specifies Hilti ™ static and dynamic anchors. According to the anchor manufacturer, the recommended design pullout force (in tension) for the specified anchors, when properly installed in cracked concrete, is provided in the side table.
  • Page 39 3. Wearing protective glasses, drill down into the flooring to the required depth as perpendicular as possible, ensuring that the foot thickness is being accounted for; refer to Anchor Selection and Foot Dimensions. 4. Insert fastener and tighten to 18 Foot-Pounds (24Nm) for 1/4” (6mm) anchor or 40 Foot-Pounds (54Nm) for 3/8” (8mm) anchor.

  • Page 40: Foot Dimensions

    Foot Dimensions Use below image to determine foot specifications. Page 38 of 38...

This manual is also suitable for:

Op-abba

Table of Contents