Page 3
Latin America and Caribbean* Germany, Austria, and Switzerland Hong Kong Life Fitness, LLC Life Fitness Europe GMBH Life Fitness Asia Pacific LTD 10601 W Belmont Ave Neuhofweg 9 26/F, Global Trade Square Franklin Park, IL 60131 U.S.A. 85716 Unterschleißheim...
Page 4
User and Service Documents Link https://lifefitness9512.zendesk.com/hc/en-us https://www.lftechsupport.com/web/document-library/documents Additional information is available online using the links above. أ علاه إل ر إبط باستخدإم إ لإ ن تر نت على إضافية معلومات تتوفر 点击上面的链接可在线获取更多信息。 Flere oplysninger er tilgængelige online gennem linket ovenfor. Bijkomende informatie is online beschikbaar via bovenstaande link.
Copyright 2023, Life Fitness, LLC. All Rights Reserved. Life Fitness, Hammer Strength, Cybex, ICG and SCIFIT are registered trademarks of Life Fitness, LLC and its affiliated companies and subsidiaries. Disclaimer: Images and specifications are current as of the date of publication and are subject to change.
• DO NOT use or permit use of any equipment that is damaged and/or has worn or broken parts. For all Life Fitness Family of Brands equipment, use only replacement parts supplied by Life Fitness Family of Brands.
Page 7
Life Fitness Family of Brands will provide service and maintenance training at our corporate facility upon request or in the field if proper arrangements are made. • Before use, examine all accessories approved for use with the Life Fitness Family of Brands equipment for damage or wear.
2. Assembly Component and Hardware List Components Item Description Qty. Base Left Leg Right Leg Left Upright Right Upright Left Upper Support Assembly Right Upper Support Assembly Center Column Left Arm Right Arm Pull-Up Bar Left Guide Rail Assembly Right Guide Rail Assembly Guide Rod Head Plate Pulley Weldment Head Plate Assembly...
Page 11
Hardware Kit 1 Item Description Qty. Hardware Kit 1, OP-DAP Screw, 8 x ¾, Phillips Screw, M5 x 0.8 HXS, 8mm Screw, M10 x 1.5, 20mm Screw, M10 x 1.5, 25mm Screw, M10 x 1.5, 50mm Screw, M10 x 1.5, 120mm Spring Guide Rod Housing Snap Link...
Hardware Kit 2 Item Description Qty. Hardware Kit 2, OP-DAP Cable End Insert Cable End Housing Cable End Link Screw, M10 x 1.5, 30mm Screw, M10 x 1.5, 80mm Pulley, 3.5" OD Pulley, 4.5" OD Tools Required • 17 mm wrench •...
Assembly Procedure Two people will be required for this procedure. TIP: Read and understand all instructions thoroughly before assembling this unit. Check all items carefully. If there is damage, see the Customer Service section of this manual for proper procedure to return, replace, or reorder parts. Assemble Frame 1.
Page 14
3. Loosely install screws, washers, and locknuts securing right arm to center column using an 8mm Allen wrench and 17mm wrench. Item Description Qty. Right Arm Center Column Screw, M10 x 1.5, 120mm 3/8" Flat Washer M10 Hex Nylock Nut Hand tighten hardware.
Page 15
6. Loosely install screws and washers securing left arm to center column using an 8mm Allen wrench. Item Description Qty. Left Arm Center Column Screw, M10 x 1.5, 20mm 3/8" Flat Washer Hand tighten hardware. 7. Place right guide rail assembly onto right leg. Loosely install screw, spacer, and locknut securing right guide rail assembly to right leg using an 8mm Allen wrench and 17mm wrench.
Page 16
8. Install screws and washers securing right guide rail assembly to right arm using an 8mm Allen wrench. Item Description Qty. Right Guide Rail Assembly Right Arm Screw, M10 x 1.5, 80mm 3/8" Flat Washer Tighten hardware to 14-16 ft-lb (19-22 Nm). NOTE: Align guide rails with decals on the underside of the arms before installing to help locate thread holes.
Page 17
10. Install screws and washers securing left guide rail assembly to left arm using an 8mm Allen wrench. Item Description Qty. Left Guide Rail Assembly Left Arm Screw, M10 x 1.5, 80mm 3/8" Flat Washer Tighten hardware to 14-16 ft-lb (19-22 Nm). 11.
Page 18
13. Loosely install screws and washers securing left upright to left leg using an 8mm Allen wrench. Item Description Qty. Left Upright Left Leg Screw, M10 x 1.5, 20mm 3/8" Flat Washer Hand tighten hardware. 14. Loosely install screws, washers, and locknuts securing left upright to left arm using an 8mm Allen wrench and 17mm wrench.
Page 19
15. Loosely install screws, washers, and locknuts securing the pull-up bar to arms using an 8mm Allen wrench and 17mm wrench. Item Description Qty. Pull-Up Bar Left Arm Right Arm Screw, M10 x 1.5, 120mm 3/8" Flat Washer M10 Hex Nylock Nut Hand tighten hardware.
Page 20
18. Tighten all hardware, starting at the bottom of the frame and working towards the top, using a torque wrench. Item Description Qty. 30-35 ft-lbs (41-47 Nm) 25-30 ft-lbs (33-40 Nm) 20-25 ft-lbs (27-33 Nm) 25-30 ft-lbs (33-40 Nm) 14-16 ft-lbs (19-22 Nm) 20-25 ft-lbs (27-33 Nm) 20-25 ft-lbs (27-33 Nm) 10-12 ft-lbs (13-16 Nm)
Install Weight Stacks 1. Slide weight stack cushions onto the guide rods. 2. Place guide rods and weight stack cushions onto base. 3. Lean guide rods outwards and slide weight stacks down guide rods onto weight stack cushions. Slide head plate assembly down guide rods and onto weight stacks.
Page 22
6. Install head plate pulley assembly to head plate bayonet. Do not tighten jam nut until after the cable is installed and final cable tension is set. See Cable Handling Guide for details. Item Description Qty. Head Plate Pulley Assembly M16 Hex Jam Nut Head Plate Bayonet Correct Depth: Thread engagement exceeds minimum...
Install Cable 1. Install threaded cable end onto carriage assembly with a hex jam nut using a 24mm wrench. Do not tighten jam nut until after the cable is installed and final cable tension is set. See Cable Handling Guide for details.
Install Pulleys 1. Install screw, washers, and locknut securing pulley to right arm using an 8mm Allen wrench and 17mm wrench. Item Description Qty. Right Arm Pulley, 3.5" OD Screw, M10 x 1.5, 50mm 3/8" Flat Washer M10 Hex Nylock Nut Tighten hardware to 14-16 ft-lb (19-22 Nm).
Page 26
4. Install screw, washers, and locknut securing pulley to right leg using an 8mm Allen wrench and 17mm wrench. Item Description Qty. Right Leg Pulley, 3.5" OD Screw, M10 x 1.5, 50mm 3/8" Flat Washer M10 Hex Nylock Nut Tighten hardware to 14-16 ft-lb (19-22 Nm). 5.
Install Shrouds 1. Press grommets into the square holes in the center column. Item Description Qty. Center Column Grommet 2. Starting at the top, press rivets into the front shrouds securing them to the uprights and center column. NOTE: Do not lock the rivets along the outer edges until after Step 4 is complete. Item Description Qty.
Page 28
4. Install screws and fender washers securing the front shrouds to the grommets in the center column using a Phillips screwdriver. Item Description Qty. Screw, 8 x ¾, Phillips Fender Washer Grommet Tighten hardware to 30-39 in-lb (3-4 Nm). NOTE: Screws should fit between the front shrouds and the fender washers should clamp the shrouds to the center column.
8. Starting at the bottom, press front shroud caps and front shroud detail onto front shrouds. Item Description Qty. Front Shroud Caps Front Shroud Detail NOTE: The front shroud detail needs to be fitted over the accessory hooks that are located on the center column. Item Description Qty.
3. Product Information Specifications Machine Weight: 719 lbs. 326 kg. Size (L x W x H): in. = 56 x 55 x 87 cm = 142 x 140 x 220 Live Area (L x W): in. = 184 x 109 x 90 cm = 467 x 277 x 229 Max User Weight: 300 lbs.
4. Exercise General Exercise Information Intended Use The intended commercial use of this machine is to aid exercise and improve general physical fitness. Multiple exercises can be performed using this product. It is the responsibility of the owner to ensure exercisers understand general use and only perform recommended exercises that do not compromise the stability of the product or put the user as risk.
Performing the Exercises NOTE: Before starting any exercise or after completing any height adjustment of the carriage assembly, verify that the pull pin is fully engaged prior to use. Poster Page 30 of 41...
5. Maintenance Procedures Maintenance Schedule ACTION DAILY WEEKLY MONTHLY AS NEEDED CLEAN Guide Rods Shrouds Hand Grips Frames INSPECT Accessories Paint Cable Hardware Frame Hand Grips Shrouds LUBRICATE Guide Rods Clean • Guide rods with a cotton cloth. • Hand grips with an approved or compatible cleaner. •...
Page 34
• Inspect all accessories, connecting links, and carabiner clips for wear. • Check condition of hand grips. • Check cables for stretch and adjust as necessary by loosening the large Jam Nut on top of the weight stack and by screwing in the Threaded Plug until cable is tight and the weight stack pin goes in all holes easily.
Who Pays Transportation and Insurance For Service If the Product or any covered part must be returned to a service facility for repairs, We, Life Fitness Family of Brands, will pay all transportation and insurance charges for the first year. You are responsible for transportation and insurance charge after the first year.
Page 36
Item 10 Years 5 Years 1 Year 90 Days Pulleys Weight Plates Guide Rods Cables Grips Bearings Hardware / Mechanical Items Not Specified Page 34 of 41...
WARNING: Use of non certified “techs” note: Service warranties may be void if a non-Life Fitness-certified technician performs service work. Replacement of any strength cables should be performed by a Life Fitness certified technician.
Tensioning Cable Cable should have enough tension so it stays seated into the pulley but not so tight that it pulls the head plate off the weight plate below it. 1. If the head plate has lifted, loosen the jam nuts at the terminations and loosen the threaded plugs a half turn until the head plate comes to rest on the weight plate below.
Strength Cable Wear Guide Replace cable at first sign of any of the following: FRACTURES: Casing can crack or fracture under strains during use. Any crack in the casing merits cable replacement even if no wire rope is exposed. Be especially observant for fractures near the components on the cable assembly - IE.
8. Bolt to Floor Guide Introduction Life Fitness Family of Brands designs its products to be stable when used as designed. Because strength training is dynamic, we cannot predict how users will ultimately use the products in all circumstances. Therefore, Life Fitness Family of Brands recommends that strength training equipment be secured to a solid, level surface to stabilize and eliminate rocking or tipping over.
3000psi (20 N/mm2) beyond anchor length Pullout Force Life Fitness specifies Hilti ™ static and dynamic anchors. According to the anchor manufacturer, the recommended design pullout force (in tension) for the specified anchors, when properly installed in cracked concrete, is provided in the side table.
• Extension cord • Impact wrench • Vacuum (for debris) Static Anchor Procedure CAUTION: If it is possible that the length of your bolt will not provide the minimum requirement of 2.5” (63.5mm) of engagement, a longer anchor should be used. 1.