Treadmill Operation - Horizon Fitness Horizon Series User Manual

TENSIONING THE RUNNING BELT
The running belt has been properly adjusted at the
factory before it was shipped. At times the belt can
move off-center during shipment.
CAUTION: Running belt should NOT be moving during
tensioning. Over-tightening the running belt can
cause excessive wear on the treadmill as well as its
components. Never over-tighten the belt.
If you can feel a slipping sensation when running on the
treadmill, the running belt must be tightened. In most
cases, the belt has stretched from use, causing the
belt to slip. This is a normal and common adjustment.
To eliminate this slipping, TURN THE TREADMILL OFF
and tension BOTH THE REAR ROLLER BOLTS using the
supplied Allen wrench, turning them 1/4 TURN to the
right as shown. Turn the treadmill on and check for
slipping. Repeat if necessary, but NEVER TURN the
roller bolts more than 1/4 turn at a time. Belt is properly
tensioned when the slipping sensation is gone.
Belt is too far to the right side
Belt is too far to the left side
12
Evolve_SS_Treadmill_Rev.1.5.indd12-13 12-13
CENTERING THE RUNNING BELT
The running belt has been properly adjusted at the
factory before it was shipped. At times the belt can
move off-center during shipment. Before operating the
treadmill, make sure the belt is centered and remains
centered to maintain smooth operation.
CAUTION: Do not run belt faster than 1 mph while
centering. Keep fingers, hair and clothing away from
belt at all times.
If the running belt is too far to the right side:
With the treadmill running at 1 mph, turn the right
adjustment bolt clockwise 1/4 TURN at a time (using
the supplied Allen wrench). Check the belt alignment.
Allow belt to run a full cycle to gauge if more adjustment
is needed. Repeat if necessary, until the belt remains
centered during use.
If the running belt is too far to the left side:
With the treadmill running at 1 mph, turn the right
adjustment bolt counter-clockwise 1/4 TURN at a time
(using the supplied Allen wrench). Check the belt
alignment. Allow belt to run a full cycle to gauge if more
adjustment is needed. Repeat if necessary, until the
belt remains centered during use.
TR EAD MIL L O PERATI ON
F B A
TIME
SPEED
DISTANCE
CALORIES
STEPS TAKEN
P R O G R A M S
P1 P2
WEIGHT
LOSS
P3 5,000 P4
STEPS
S P E E D
S I M P L E S T E P S
H G
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed.
A) LCD DISPLAY: Time, Speed, Distance, Calories and Steps Taken.
B) FEEDBACK LEDS: Indicate what workout feedback is currently being displayed.
C) CHANGE DISPLAY BUTTON: Press to change the feedback on the LCD display. Hold for 2-3 seconds to scan.
D) START: Simply press to begin exercising or starts your program.
E) STOP/PAUSE: Press to pause/end your workout. Hold for 3 seconds to reset the treadmill.
F) SPEED ARROW KEYS: Used to adjust speed in small increments (1-6 mph in 0.1 mph increments).
G) PROGRAM KEYS: Used to select desired program.
H) SAFETY KEY POSITION: Enables treadmill when safety key is inserted.
I) READING RACK: Holds reading material.
C D I
COUNTING YOUR STEPS:
Choose a step count goal of 2000, 5000 or 10000 steps
Wear your pedometer throughout the day to track your step count
C HANGE H O L D
While standing on the treadmill, press and hold SEND on your pedometer
D I SPLAY T O
S C A N
The treadmill will receive your step count from your pedometer
Select 2000, 5000 or 10000 steps program and press START
The program will end when you reach your step count goal
2,000
STEPS
S T A R T
10,000 Q U I C K S T A R T
STEPS
H O L D T O R E S E T
S T O P
P A U S E
SA FE TY KE Y
E
1
6/23/08 2:43:20 PM