Advertisement
Read the TREADMILL GUIDE before using this OWNER'S MANUAL.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirment. The device can be used in portable exposure condition without restriction.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
SAVE THESE INSTRUCTIONS
When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. If you have any questions after reading this guide, contact Customer Tech Support at the number listed on the back panel of the OWNER'S MANUAL.
This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.
TO REDUCE THE RISK OF ELECTRICAL SHOCK:
Always unplug the treadmill from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or taking off parts.
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.
This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service provider if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 110-120 Volt circuit and has a grounding plug that looks like the plug in the illustration. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.
This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one circuit. This treadmill should be used with a minimum 15-amp circuit.
Connect this exercise product to a properly grounded outlet only.
Never operate product with a damaged cord or plug even if it is working properly. Never operate any product if it appears damaged, or has been immersed in water. Contact Customer Tech Support for replacement or repair.
Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack and assemble the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. You may remove the plastic wrap from console masts.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill's serial number located on a white barcode sticker near the on/off power switch and power cord and enter it in the space provided below. ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
KEEP HANDS AND FEET AWAY FROM THIS AREA. HIGH-PRESSURE SHOCKS COULD CAUSE BODILY INJURY.
TOOLS INCLUDED:
PARTS INCLUDED:
NEED HELP?
If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual.
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack and assemble the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. You may remove the plastic wrap from console masts.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.
STEP 1
HARDWARE FOR STEP 1 | |||
PART | TYPE | DESCRIPTION | QTY |
A | BOLT | M6X1.0PX10L | 8 |
NOTE: Do not fully tighten bolts until STEP 5.
STEP 2
HARDWARE FOR STEP 2 | |||
PART | TYPE | DESCRIPTION | QTY |
A | BOLT | M8X1.25PX20L | 4 |
B | SPRING WASHER | 8.2X15.4X2T | 4 |
C | FLAT WASHER | 8.4X15.5X6T | 4 |
NOTE: Do not fully tighten bolts until STEP 5.
STEP 3
HARDWARE FOR STEP 3 | |||
PART | TYPE | DESCRIPTION | QTY |
A | BOLT | M8X1.25PX20L | 4 |
B | SPRING WASHER | 8.2X15.4X2T | 4 |
C | FLAT WASHER | 8.4X15.5X6T | 4 |
NOTE: Do not tighten bolts completely until after the console is assembled.
STEP 4
HARDWARE FOR STEP 4 | |||
PART | TYPE | DESCRIPTION | QTY |
A | BOLT | M8X1.25PX15L | 4 |
B | SPRING WASHER | 8.2X15.4X2.0T | 4 |
C | FLAT WASHER | 8.4X15.5X1.6T | 4 |
NOTE: Be careful not to pinch any wires while assembling the console.
STEP 5
HARDWARE FOR STEP 5 | |||
PART | TYPE | DESCRIPTION | QTY |
A | SCREW | 4X10L | 4 |
B | SCREW | 4X15L | 4 |
This section explains how to use your treadmill's console and programming.
The BASIC OPERATION section in the TREADMILL GUIDE has instructions for the following:
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
QUICK START UP
Simply press the START key to begin working out. Time, distance, and calories will all count up from zero. OR...
SELECT A WORKOUT OR TARGET
Segment | Warm Up | 1 | 2 | Cool Down | ||
Time | 4:00 Mins | 90 sec | 30 sec | 4:00 Mins | ||
Level 1 | 0.5 | 1.5 | 2 | 4 | 1.5 | 1 |
Level 2 | 0.5 | 1.5 | 2 | 4.5 | 1.5 | 1 |
Level 3 | 0.5 | 1.9 | 2.5 | 5 | 1.9 | 1.3 |
Level 4 | 1 | 1.9 | 2.5 | 5.5 | 1.9 | 1.3 |
Level 5 | 1 | 2.3 | 3 | 6 | 2.3 | 1.5 |
Level 6 | 1 | 2.3 | 3 | 6.5 | 2.3 | 1.5 |
Level 7 | 1.4 | 2.6 | 3.5 | 7 | 2.6 | 1.8 |
Level 8 | 1.4 | 2.6 | 3.5 | 7.5 | 2.6 | 1.8 |
Level 9 | 1.4 | 3 | 4 | 8 | 3 | 2 |
Level 10 | 1.4 | 3 | 4 | 8.5 | 3 | 2 |
Segment | Warm Up | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | Cool Down | |||
Time | 4:00 Mins | 30 sec | 30 sec | 30 sec | 30 sec | 30 sec | 30 sec | 30 sec | 30 sec | 4:00 Mins | |||
Level 1 | lncline | 0 | 0.5 | 1.5 | 1.5 | 1 | 0.5 | 0.5 | 0.5 | 1 | 1.5 | 0.5 | 0 |
Speed | 0.5 | 1.5 | 2 | 2.5 | 3 | 3.5 | 4 | 3.5 | 3 | 2.5 | 2.3 | 1.5 | |
Level 2 | lncline | 0 | 0.5 | 1.5 | 1.5 | 1 | 0.5 | 1 | 0.5 | 1 | 1.5 | 0.5 | 0 |
Speed | 0.5 | 1.9 | 2.5 | 3 | 3.5 | 4 | 4.5 | 4 | 3.5 | 3 | 2.6 | 1.8 | |
Level 3 | lncline | 0.5 | 1 | 2 | 2 | 1.5 | 1 | 1 | 1 | 1.5 | 2 | 1 | 0.5 |
Speed | 0.5 | 2.3 | 3 | 3.5 | 4 | 4.5 | 5 | 4.5 | 4 | 3.5 | 3 | 2 | |
Level 4 | lncline | 0.5 | 1 | 2 | 2 | 1.5 | 1 | 1 | 1 | 1.5 | 2 | 1 | 0.5 |
Speed | 1 | 2.6 | 3.5 | 4 | 4.5 | 5 | 5.5 | 5 | 4.5 | 4 | 3.4 | 2.3 | |
Level 5 | lncline | 1 | 1.5 | 2.5 | 2.5 | 2 | 1.5 | 1.5 | 1.5 | 2 | 2.5 | 1.5 | 1 |
Speed | 1 | 3 | 4 | 4.5 | 5 | 5.5 | 6 | 5.5 | 5 | 4.5 | 3.8 | 2.5 | |
Level 6 | lncline | 1 | 1.5 | 2.5 | 2.5 | 2 | 1.5 | 1.5 | 1.5 | 2 | 2.5 | 1.5 | 1 |
Speed | 1 | 3.4 | 4.5 | 5 | 5.5 | 6 | 6.5 | 6 | 5.5 | 5 | 4.1 | 2.8 | |
Level 7 | lncline | 1.5 | 2 | 3 | 3 | 2.5 | 2 | 2 | 2 | 2.5 | 3 | 2 | 1.5 |
Speed | 1.4 | 3.8 | 5 | 5.5 | 6 | 6.5 | 7 | 6.5 | 6 | 5.5 | 4.5 | 3 | |
Level 8 | lncline | 1.5 | 2 | 3 | 3 | 2.5 | 2 | 2 | 2 | 2.5 | 3 | 2 | 1.5 |
Speed | 1.4 | 4.1 | 5.5 | 6 | 6.5 | 7 | 7.5 | 7 | 6.5 | 6 | 4.9 | 3.3 | |
Level 9 | lncline | 2 | 2.5 | 3.5 | 3.5 | 3 | 2.5 | 2.5 | 2.5 | 3 | 3.5 | 2.5 | 2 |
Speed | 1.4 | 4.5 | 6 | 6.5 | 7 | 7.5 | 8 | 7.5 | 7 | 6.5 | 5.3 | 3.5 | |
Level 10 | lncline | 2 | 2.5 | 3.5 | 3.5 | 3 | 2.5 | 2.5 | 2.5 | 3 | 3.5 | 2.5 | 2 |
Speed | 1.4 | 4.9 | 6.5 | 7 | 7.5 | 8 | 8.5 | 8 | 7.5 | 7 | 5.6 | 3.8 |
Hold STOP key for 3 seconds.
When your workout is complete, the unit will beep. Your workout information will stay displayed on the console for 30 seconds and then reset.
WEIGHT CAPACITY = 300 lbs (136 kilograms)
FRAME • LIFETIME
Horizon Fitness warrants the frame against defects in workmanship and materials for the lifetime of the original owner, so long as the device remains in the possession of the original owner. (The frame is defined as the welded metal base of the unit and does not include any parts that can be removed.)
MOTOR • LIFETIME
Horizon Fitness warrants the motor against defects in workmanship and materials for the lifetime of the original owner, so long as the device remains in the possession of the original owner. Labor or installation of motor is not covered under the motor warranty.
ELECTRONICS & PARTS • 1 YEAR
Horizon Fitness warrants the electronic components, finish and all original parts for a period of one year from the date of original purchase, so long as the device remains in the possession of the original owner.
LABOR • 1 YEAR
Horizon Fitness shall cover the labor cost for the repair of the device for a period of one year from the date of the original purchase, so long as the device remains in the possession of the original owner.
Who IS covered:
What IS covered:
What IS NOT covered:
DO NOT RETURN TO THE RETAILER if you have any problems during assembly or if parts are missing.
For fast and friendly service, please contact one of our trained customer technicians via phone, email or our website.
We want to know if you have a problem and we want to have an opportunity to correct it for you.
NOTE: Please read the TROUBLESHOOTING section in the TREADMILL GUIDE before contacting Customer Tech Support. Additional product information is available on our website.
USA & CANADA:
1-855-396-2524
techsupport@horizonfitness.com
www.horizonfitness.com
Horizon Fitness
1600 Landmark Drive,
Cottage Grove WI, 53527
Horizon T101-5 040618 © 2018 Horizon Fitness
Designed & Engineered in the U.S.A. • Made in China
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the T101 that isn't answered in the manual? Leave your question here.