Table of Contents
Advertisement
Please Note!
If during delivery you want to stop preparing milk, press the
cappuccino icon or interrupt preparation of the coffee by
pressing the
icon.
making macchiato
1. After attaching the milk container (see previous section),
position the froth regulator on LATTE MACCHIATO (fig. 27)
printed on the milk container lid.
2. Press the LATTE MACCHIATO icon (fig. 28). A glass is di-
splayed and gradually fills as preparation progresses. Af-
ter a few seconds, frothed milk flows out of the milk spout
into the glass below. Milk delivery stops automatically
and coffee delivery begins.
3. At the end of delivery, the machine is automatically ready
for use again.
Please Note!
If during delivery you want to stop preparing milk, press the
LATTE MACCHIATO icon or interrupt preparation of the coffee by
pressing the
icon.
making milk
1. After attaching the milk container (See section: "Filling
and attaching the milk container"), position the froth re-
gulator according to the quantity of froth you require (pos.
3 caffelatte = little froth; pos. 1 cappuccino = abundant
froth).
2. Press the MILK icon (fig. 29). A glass is displayed and gra-
dually fills as preparation progresses. After a few seconds,
frothed milk is delivered from the milk spout into the cup
below.
3. After delivery, the machine is automatically ready for use
again.
Please Note!
If during delivery you want to stop preparing milk, press the
milK icon once.
cleaning the milk container after use
Important! Danger of burns
When cleaning the internal tubes of the milk container, a little
hot water leaks out of the frothed milk tube (B5). Avoid contact
with splashes of water.
When "Press CLEAN button" flashes on the display (each time
you use a milk function):
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk spout
(fig. 21).
3. Press the CLEAN button (fig. 30) and keep pressing until
the progress bar which appears on the display together
with the message "Cleaning..." is complete.
4. Remove the milk container and always clean the nozzle
with a sponge (fig. 31).
Please Note!
•
When " Press CLEAN button" flashes on the display, you can
still prepare any type of coffee or milk. If you have to make
a number of drinks with milk, wait until you have delive-
red the last cup before cleaning the container.
•
The milk left in the container can be kept in the refrigera-
tor.
•
In some cases, to clean you must wait for the appliance to
heat up, holding the CLEAN button down.
programming the quantities of coffee and milk in the
cup
The appliance is set by default to automatically deliver stan-
dard quantities.
To change these quantities, proceed as follows:
1. Place a cup/glass under the coffee spouts and milk spout
(fig. 21).
2. Press the icon corresponding to the function you want to
program until "Program Quantity Milk For..." is displayed
together with the
ction selected.
3. Release the icon. The appliance starts delivering milk.
4. When the required quantity of milk has been delivered
into the cup, press the icon again.
5. After a few seconds, the appliance starts delivering coffee
into the cup and the message "Coffee for... Program quan-
tity" is displayed (with the exception of the MILK function)
and the
icon flashes.
6. As soon as the coffee in the cup reaches the required level,
press the
icon. Coffee delivery stops.
The machine is now reprogrammed with the new quantities.
hEatinG WatEr
preparation
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water.
The hot water spout becomes hot while water is delivering and
must be handled by the handle only.
1. Make sure the hot water spout is attached correctly (fig.
4).
2. Place a container under the spout (as close as possible to
16
or
icon according to the fun-
Advertisement
Table of Contents
Troubleshooting
