Page 1
SERVICE MANUAL T3.60F / T3.70F / T3.80F Tractor Part number 51553302 edition English November 2018...
Page 2
SERVICE MANUAL T3.60F T3.70F T3.80F 51553302 19/11/2018 Find manuals at https://best-manuals.com...
Page 3
Link Product / Engine Product Market Product Engine T3.60F North America 8035.25A IIIB T3.70F North America 8035.25B IIIB T3.80F North America 8035.25C IIIB 51553302 19/11/2018 Find manuals at https://best-manuals.com...
INTRODUCTION Safety rules Pay attention to this symbol This warning symbol points out important messages con- cerning your safety. Carefully read the following safety regulations and ob- serve advised precautions in order to avoid potential haz- ards and safeguard your health and safety. In this manual the symbol is accompanied by the following key-words: WARNING: Warnings concerning unsuitable repair oper-...
Page 9
INTRODUCTION • The fuel nozzle should always be in contact with the filling aperture: Maintain this contact until the fuel stops flowing into the tank to avoid possible sparks due to static electricity buildup. • Only use specified towing points for towing the vehicle. Connect parts carefully. Make sure that all pins and/or locks are secured in position before applying traction.
Page 10
INTRODUCTION Starting • Never run the engine in confined spaces that are not equipped with adequate ventilation for exhaust gas extraction. • Never place the head, body, limbs, feet, hands or fingers near fans or rotating belts. Engine • Always loosen the radiator cap slowly before removing it to allow any remaining pressure in the system to be dis- charged.
Page 11
INTRODUCTION Removal and re-fitting • Lift and handle all heavy parts using suitable hoisting equipment. Make sure that parts are sustained by appropriate hooks and slings. Use the hoisting eyebolts for lifting operations. Extra care should be taken if persons are present near the load to be lifted.
Basic instructions Important notice All maintenance and repair work described in this manual must be performed exclusively by NEW HOLLAND service technicians, in strict accordance with the instructions given and using any specific tools necessary. Anyone performing the operations described herein without strictly following the instructions is personally responsible for any eventual injury or damage to property.
Page 13
• Part number of the ordered part, which can be found on the “Spare Parts Catalogue”, which is the base for order processing. Notes for equipment The tools that NEW HOLLAND offer and illustrate in this manual are: • Specifically researched and designed for use with NEW HOLLAND vehicles. • Necessary to make a reliable repair.
Engine - Engine and crankcase Engine and crankcase - Disassemble ENGINE – Removal ATTENTION: Use appropriate equipment to hold and lift heavy parts. Make sure that that the body and parts are safely supported safely by ropes and hooks. Make sure that no one is close when you lift heavy loads.
Page 24
Engine - Engine and crankcase 4. Remove the front weight connection rod (1). ANIL17TRO0992AA 5. Remove the front weight lower connection rod (1). ANIL17TRO0930AA 6. Remove the front weights (1). ANIL17TRO0931AA 51553302 19/11/2018 10.1 [10.001] / 5...
Page 25
Engine - Engine and crankcase 7. (1)Use the specific tool to discharge the refrigerant from the system via the greasers and (2). Remove the bracket strips and separate the two lines. 380000315 ANIL1800789AA 8. (1) Place a suitable container under the drain plug for the gearbox transmission oil (1) .
Page 26
Engine - Engine and crankcase 11. Remove the front center and rear retaining bolts on the front wheel drive control shaft housing. Then remove the guard. (1). WLAPL4S10C112AA 12. Remove the retaining ring (2). Move the front screen in the direction of the arrow (1) to remove the screen from the grooves on the front axle.
Page 27
Engine - Engine and crankcase 15. Disconnect all electrical connections that prevent the engine from being removed from the gearbox trans- mission housing. For example, the main connections (1), the main cab and power connections (2), the en- gine control unit connections (3), the fuse box (4), the sensors, and the extensions, depending on the tractor model.
Page 28
Engine - Engine and crankcase 17. Remove the electrical connections (1) on the fuel pump ANIL18TRO1171AA 18. Remove main electrical connection (1). ANIL18TRO1172AA 51553302 19/11/2018 10.1 [10.001] / 9...
Page 29
Engine - Engine and crankcase 19. Remove the electrical connections (1) on the EGR valve and suction line. ANIL18TRO1173AA 20. Remove the electrical connection (1) on the brake oil reservoir ANIL18TRO1089AA 51553302 19/11/2018 10.1 [10.001] / 10...
Page 30
Engine - Engine and crankcase 21. Remove the electrical connection (1) on the Waste- gate actuator. ANIL18TRO1174AA 22. Remove the oil pipes (1) on right hand side of the front panel ANIL18TRO1175AA 51553302 19/11/2018 10.1 [10.001] / 11...
Page 31
Engine - Engine and crankcase 23. Remove the electrical connections (1) on fuel filter ANIL18TRO1176AA ANIL18TRO1177AA 51553302 19/11/2018 10.1 [10.001] / 12...
Page 32
Engine - Engine and crankcase 24. Remove the electrical connection (1) of the engine fuse panel. ANIL18TRO1178AA 25. Remove the electrical connections (1) on each fuel injector ANIL18TRO1180AA 51553302 19/11/2018 10.1 [10.001] / 13...
Page 33
Engine - Engine and crankcase 26. Remove the electrical connections (1) between en- gine and front panel ANIL18TRO1182AA 27. Remove the crank shaft sensor (1) and cam shaft sen- sor (2) ANIL18TRO1183AA 51553302 19/11/2018 10.1 [10.001] / 14...
Page 34
Engine - Engine and crankcase 28. Remove the electrical connections on the alternator (1) . ANIL18TRO1184AA 29. Remove the engine vent pipe (1) . ANIL18TRO1185AA 51553302 19/11/2018 10.1 [10.001] / 15...
Page 35
Engine - Engine and crankcase 30. Remove the NOx sensor (1) on the DOC ANIL18TRO1186AA 31. Remove engine oil pressure sensor (1) ANIL18TRO1187AA 51553302 19/11/2018 10.1 [10.001] / 16...
Page 36
Engine - Engine and crankcase 32. Remove fuel pipe (1) from fuel tank ANIL18TRO1188AA 33. Remove coolant pipe (1) form engine ANIL18TRO1189AA 51553302 19/11/2018 10.1 [10.001] / 17...
Page 37
Engine - Engine and crankcase 34. Remove exhaust pipe (1) from DOC ANIL18TRO1190AA 35. Remove the retaining bolts (1). Remove the top ra- diator guard (2). Remove all the remaining free wire bundles. MOIL13TR02942AA 36. Loosen the strip on the inlet of the hose (1) that feeds fluid to the radiator.
Page 38
Engine - Engine and crankcase 38. Loosen the strip. Disconnect the hose (1) that runs from the air filter to the turbine. Next, remove the two bolts (3) and remove the bracket (2). MOIL13TR02890AB 39. Loosen the strip (1). Remove the hose (2) that con- nects the air filter to the injection pump.
Page 39
Engine - Engine and crankcase 42. Place the moving tractor separator tool (2) under the engine with the mounting bracket and the adapter plate. Place a wooden block (1) at the points of con- tact between the tool and the motor. Chock the axle to prevent the axle from shaking.
Page 40
Engine - Engine and crankcase 46. Place a wooden stop between parts (3) and (1). Place a fixed lifting jack (3) under the front axle drive groove (1) bracket. WLAPL4S10C133A 47. With the connection assembly firmly secure, place a lifting jack at the rear of the engine to leave slack in the winch.
Page 41
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...