Advertisement
Quick Links
Advertisement
Related Manuals for Ricoh L5160
Summary of Contents for Ricoh L5160
- Page 1 CIP Training L5160/L5130 Input DWT134...
-
Page 3: Setting Media
CIP Training L5160/L5130 Setting Media Setting Media This section explains how to set media. Roll media and leaf media are supported. For details about supported media or precautions for handling media. Precautions for Setting Media Make sure to understand the following precautions before setting media: •... - Page 4 CIP Training L5160/L5130 Setting Media About the scales on the machine The post-heater and pre-heater have a scale display on top. Use this scale as a guide when setting media. • Skewing may occur because of uneven stretching of the media at its edges, so do not try to align the media to "0"...
-
Page 5: Setting Roll Media
CIP Training L5160/L5130 Setting Media Setting Roll Media • Do not leave the media with the heater ON for a long time. This section explains how to set roll media. Set roll media while the machine's power is turned If media has already been set, see page 68 "Changing Roll Media". - Page 6 CIP Training L5160/L5130 Setting Media When using media whose printing surface is rolled up on the inside DWT123 3. Release the roll holder's holding lever on the left side of the back of the machine. DWT124 4. Move the position of the roll holder to match the roll core size of the set media.
- Page 7 CIP Training L5160/L5130 Setting Media DWT126 If the roll holder's lock is weak and the media moves, hold the media while attaching it. 7. Release the roll holder's holding lever on the right side of the back of the machine.
- Page 8 CIP Training L5160/L5130 Setting Media 9. Lock the roll holder's holding lever. DWT129 Lock the holding lever with the roll holder pressed thoroughly into the roll core. If the amount of force used to press the roll holder into the roll core is insufficient, the media may hang down and touch the floor.
- Page 9 CIP Training L5160/L5130 Setting Media • If the media is difficult to insert because the edges of the media are getting caught, diagonally insert the media between the rollers, so that one corner gets inserted first. Ensure the media is inserted evenly, and begin feeding.
- Page 10 CIP Training L5160/L5130 Setting Media 14. While holding down the center of the media, lower the media holding lever (back). The pinch rollers lower and the media is fixed. DWT133 15. Return the pre-heater cover to its original position. • After returning the pre-heater cover to its original position, press its ends to make sure that it is not bulging.
- Page 11 CIP Training L5160/L5130 Setting Media 19. While holding down the center of the media, lower the media holding lever (front). The pinch rollers lower and the media is fixed. Since the pinch rollers may stop half way because of the shock-absorbing stopper, make sure the media holding lever is lowered completely.
- Page 12 CIP Training L5160/L5130 Setting Media 23. Move to the rear of the printer and check for warping in the media. If the roll media is slack, rotate it to take up the slack. • Slack • Slack eliminated EDP010 EDP011 If the media's slack is uneven, return to Step 11 and try loading the media again.
- Page 13 CIP Training L5160/L5130 Setting Media DWT141 27. Lock the roll core holder's holding lever. DWT142 28. Press [Yes] on the confirmation screen for media replacement. If the media is not going to be replaced and it is not necessary to change the media settings, press [No] and proceed to Step 41.
- Page 14 CIP Training L5160/L5130 Setting Media 30. Press [Remaining Media]. When [Display Remaining Media] is set to [On] in [Media Display Settings] on the [Initial Setting] screen, the input screen for the remaining amount of media is displayed after detecting the media width. For details, see "Registering the Remaining Amount of Media".
- Page 15 CIP Training L5160/L5130 Setting Media • When you load the media, if the arm near the media cutter is positioned behind the media, you cannot cut the media correctly. Correct Incorrect DWT074 DWT075 DWT076 If you touch the cutter part, the arm near the cutter may close. If this happens, move the media to a position unreachable by the cutter, and then execute [Origin Setting / Cut] to cut.
- Page 16 CIP Training L5160/L5130 Setting Media Fix the central tip of the media to the empty roll core with adhesive tape. When using soft media, fix the right edge, center, and left edge with adhesive tape. • When fixing the left edge, center, and right edge with adhesive tape, after fixing the center, pull the left and right sides of the media equally, and then fix the left and right edges so that sagging or wrinkles cannot occur.
- Page 17 CIP Training L5160/L5130 Setting Media 45. Set the roll-up switch to the on position. When placing the printing surface on the outside and rolling up media Lower the roll-up switch (normal rotation). DWT147 When placing the printing surface on the inside and rolling up media Raise the roll-up switch (reverse rotation).
- Page 18 CIP Training L5160/L5130 Setting Media Changing Roll Media This section explains how to remove and change roll media. Change the roll media with the machine turned on. 1. Press [Origin Setting/Cut] on the bottom right of the screen. 2. Press [Feed] or [Rewind] to feed the media to the cutting position.
- Page 19 CIP Training L5160/L5130 Setting Media 6. Release the roll core holder's holding lever on the left side of the front of the machine. DWT150 7. Move the roll core holder to the left to remove the roll core. Hold the roll core while removing it so that it does not fall down.
- Page 20 CIP Training L5160/L5130 Setting Media DWT139 10. Move the roll core holder on the left side of the front of the machine to the right to insert the empty roll core. Insert the roll core as far as possible so that it does not move.
- Page 21 CIP Training L5160/L5130 Setting Media 14. While holding down the center of the media, roll up the remaining media. DWT154 15. Return the pre-heater cover to its original position. 16. Grab the handle on the back of the machine to pull out the roll feed unit.
- Page 22 CIP Training L5160/L5130 Setting Media 19. Remove the roll media from the roll holder on the left side of the back of the machine. DWT158 20. Return the roll feed unit to its original position. DWT159 21. Set new media.
-
Page 23: Setting Leaf Media
CIP Training L5160/L5130 Setting Media Setting Leaf Media This section explains how to set leaf media. • If media is not on the rear media sensor, it cannot be detected correctly. Leaf media should have a length of over 1,000 mm (approx. 39.4 inches). Additionally, in order to ensure dry feeding, we recommend the print image to have a rear margin of at least 870 mm. - Page 24 CIP Training L5160/L5130 Setting Media 4. While holding down the center of the media, lower the media holding lever (back). The pinch rollers lower and the media is fixed. DWT167 Return the pre-heater cover to its original position. • After returning the pre-heater cover to its original position, press its ends to make sure that it is not bulging.
- Page 25 CIP Training L5160/L5130 Setting Media 8. While holding down the center of the media, pull the media straight out to the media output location. • Check that the media has been pulled out evenly. • Use the scale on the post-heater to check the position of the right edge of the media.
- Page 26 CIP Training L5160/L5130 Setting Media 13. Close the center cover. When the media has set correctly, a confirmation screen appears on the control panel. 14. Press [Yes] on the confirmation screen for media replacement. If you do not need to change the media settings, press [No] to proceed to Step 25.
- Page 27 CIP Training L5160/L5130 Setting Media 26. Press [Completed]. Wait until "Ready" is displayed on the home screen. • If an unsupported media is set, "Cannot detect the media." appears. Set supported media again. For details about supported media, see "Supported Media".