Shure Incorporated Table of Contents Power Over Ethernet AD610 ShowLink® Access Point External Power Supply (Optional) IMPORTANT SAFETY INSTRUCTIONS Networking AD610 ShowLink Access Point Reset Option Features Positioning the Access Point ShowLink Access Point Overview Network Mode Furnished Accessories Control and Configure the Access Point with Wireless...
Shure Incorporated AD610 ® ShowLink Access Point IMPORTANT SAFETY INSTRUCTIONS READ these instructions. KEEP these instructions. HEED all warnings. FOLLOW all instructions. DO NOT use this apparatus near water. CLEAN ONLY with dry cloth. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturer’s instructions.
Shure Incorporated Caution: risk of danger (See note.) Direct current Alternating current On (Supply) Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION Stand-by Equipment should not be disposed of in the normal waste stream WARNING: Voltages in this equipment are hazardous to life. No userserviceable parts inside. Refer all servicing to qualified service personnel. The safety cer tifications do not apply when the operating voltage is changed from the factory setting.
Page 5
Shure Incorporated ShowLink Access Point Overview ① ShowLink 2.4 GHz detachable antennas For 2.4 GHz signals ② ShowLink Data Status LED (blue) ◦ ON Steady: Linked, no data transmission ◦ Flashing: Transmitting data. Rate of flashing indicates level of activity ③...
Shielded 25 foot Ethernet cable for ShowLink access point, RJ45-to-EtherCon con- 95A15104 nector Power Supply PS43 Note: Model availability depends on region. See your local Shure dealer or distributor for details. Optional Accessories Directional 2.4 GHz patch antenna AXT644 (available depending on regional regulations) ShowLink Basics ShowLink Channels and 2.4 GHz Spectrum...
Power Over Ethernet The Shure Ethernet switch and Axient rack components offer network ports with Power over Ethernet (PoE). The network port powers the access point as long as the host component is powered on. Insert a Cat 5 Ethernet cable into the Ethernet port located on the body of the access point.
Shure Incorporated External Power Supply (Optional) If Power over Ethernet (PoE) is not available, power the access point using an external power supply. Connect the power supply to the external power supply jack. Tighten the locking ring to secure the plug.
Page 9
Shure Incorporated Positioning the Access Point • Provide a clear line of sight between the access point and devices. Mount the access point on a microphone stand or wall to elevate above obstructions. • Position the antennas vertically for optimal performance. The swivel joint on each antenna allows a wide range of position ing to maintain a vertical alignment.
Shure Incorporated Wall Mount Network Mode Set a host ID on the AD610 to connect to an ADX5D portable receiver in network mode. An AD610 with a host ID set grants ac cess to ADX5Ds with a matching client ID. Update your AD610 to the latest firmware and download the latest version of Wireless Workbench. Connect the access point to your network using a Class 1 Power over Ethernet (PoE) port.
Shure Incorporated Tip: The text color of the device ID for each transmitter in the Connected list indicates link quality: • Green = Excellent • Yellow = Good • Red = Marginal Hovering the cursor over the Device ID displays link quality ranked from 5 to 1.
Page 12
Shure Incorporated Dimensions 190 mm x 102 mm x 47 mm (7.48 in. x 4 in. x 1.85 in.) H x W x D, without antennas Weight 464 g (16.3 oz.), without antennas Housing Extruded Aluminum Power Requirements Power over Ethernet (PoE) Class 1 36 to 57 V DC/V AC External Power Supply (if PoE is unavailable) 15 V DC (600 mA), double insulated...
This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking. Hereby, Shure Incorporated declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.shure.com/europe/compliance...
Important Product Information LICENSING INFORMATION Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability de pends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the ...