Table of Contents
Advertisement
Available languages
Available languages
Installation
4 Power cord input
5 Red
5 Wired remote input
6 Red
Hard-wired remote control adapter can be
connected (sold separately).
6 Microphone input
7 Microphone
7 Connect leads of the same color to each
4 m
8 Rear output
8 Orange/white
9 Front output
a Subwoofer output
9 Black (chassis ground)
a Blue/white
b USB cable
1.5 m
Power cord
3
4
b Blue/white
1
5
6
2
c Blue/white
3
4
d Speaker leads
5
6
7
8
9
c
a
b
e
e ISO connector
d
1 To power cord input
2 Depending on the kind of vehicle, the func-
tion of 3 and 5 may be different. In this
! Change the set up menu of this unit. Refer to
case, be sure to connect 4 to 5 and 6 to
3.
3 Yellow
Back-up (or accessory)
4 Yellow
Connect to the constant 12 V supply termi-
nal.
Accessory (or back-up)
Connect to terminal controlled by ignition
switch (12 V DC).
other.
Connect to lighting switch terminal.
The pin position of the ISO connector will dif-
fer depending on the type of vehicle. Connect
a and b when Pin 5 is an antenna control
type. In another type of vehicle, never con-
nect a and b.
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Connect to auto-antenna relay control termi-
nal (max. 300 mA 12 V DC).
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left + or subwoofer +
Green/black: Rear left * or subwoofer *
Violet: Rear right + or subwoofer +
Violet/black: Rear right * or subwoofer *
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.
Notes
S/W control (rear output and subwoofer set-
ting) on page 19.
The subwoofer output of this unit is monau-
ral.
Installation
! When using a subwoofer of 70 W (2 W), be
! Consult your dealer if installation requires
sure to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
! Do not install this unit where:
connect anything to the green and green/
black leads.
Power amp (sold separately)
! The semiconductor laser will be damaged if
Perform these connections when using the op-
tional amplifier.
! Optimum performance is obtained when the
3
1
2
4
5
5
3
2
1
6
! When installing, to ensure proper heat dis-
7
7
3
2
1
8
9
9
1 System remote control
Connect to Blue/white cable.
2 Power amp (sold separately)
3 Connect with RCA cables (sold separately)
4 To Rear output
5 Rear speaker
6 To Front output
7 Front speaker
8 To subwoofer output
9 Subwoofer
DIN front/rear mount
This unit can be properly installed using either
front-mount or rear-mount installation.
Installation
Use commercially available parts when instal-
Important
ling.
! Check all connections and systems before
final installation.
! Do not use unauthorized parts as this may
cause malfunctions.
Section
03
drilling of holes or other modifications to the
vehicle.
it may interfere with operation of the vehicle.
it may cause injury to a passenger as a result
of a sudden stop.
it overheats. Install this unit away from hot
places such as near the heater outlet.
unit is installed at an angle of less than 60°.
60°
persal when using this unit, make sure you
leave ample space behind the rear panel and
wrap any loose cables so they are not block-
ing the vents.
Leave ample
5 cm
space
5 cm
21
En
Advertisement
Table of Contents
