Onkyo TX-NR797 Instruction Manual page 135

2. Speaker
„ 1. Configuration
Change the settings of connection environment of the speakers.
Setting Item Default Value
Speaker 7.1.2 ch
Channels
Subwoofer Yes
Height 1 Speaker Top Middle
Setting Details
Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch",
"6.1 ch", "7.1 ch", "2.1.2 ch", "3.1.2 ch", "4.1.2 ch",
"5.1.2 ch", "6.1.2 ch", "7.1.2 ch", "4.1.4 ch" or
"5.1.4 ch" to suit the number of speaker channels
connected.
Set whether a subwoofer is connected or not.
"Yes": When a subwoofer is connected
"No": When a subwoofer is not connected
Set the speaker type if height speakers are
connected to the HEIGHT 1 terminals. Select "Top
Middle", "Top Rear", "Rear High", "Dolby Speaker
(Front)", "Dolby Speaker (Surr)", "Dolby Speaker
(Back)", "Front High" or "Top Front" according to
the type and layout of the connected speakers.
• This setting cannot be selected under any of
following conditions. Set the height speakers
type to "Height 2 Speaker".
– "Bi-Amp" is set to "Yes"
– When "Speaker Channels" is set to "2.1.2 ch",
"3.1.2 ch", "4.1.2 ch " or "5.1.2 ch", and "Zone
Speaker" is set to "Zone 2"
• When two sets of height speakers are being used,
"Top Rear", "Rear High", "Dolby Speaker (Surr)",
and "Dolby Speaker (Back)" cannot be selected.
• "Dolby Speaker (Surr)" and "Dolby Speaker (Back)"
can only be selected when surround speakers
or surround back speakers are being used,
respectively. You can check speakers that you are
using on the figure displayed in "Speaker Channels".
• If an item cannot be selected even though
connection is correct, check that the settings
in "Speaker Channels" matches the number of
connected channels.
Contents Connections
≫
Setting Item Default Value
Height 2 Speaker Rear High
Zone Speaker No
135
Front Panel≫ Rear Panel≫ Remote≫
Playback Setup
≫ ≫
Setting Details
Set the speaker type if height speakers are
connected to the HEIGHT 2 terminals. Select
"Front High", "Top Front", "Top Middle", "Top Rear",
"Rear High", "Dolby Speaker (Front)" or "Dolby
Speaker (Surr)" according to the type and layout
of the connected speakers. However, the options
selectable for the "Height 1 Speaker" the are as
follows.
If "Height 1 Speaker" is set to "Front High": Select
from "Top Middle", "Top Rear", "Rear High" or
"Dolby Speaker (Surr)".
If "Height 1 Speaker" is set to "Top Front" or "Dolby
Speaker (Front)": Select from "Top Rear", "Rear
High" or "Dolby Speaker (Surr)".
If "Height 1 Speaker" is set to "Top Middle": Fixed
to "Rear High".
• "Dolby Speaker (Surr)" can only be selected
when surround speakers are being used. You
can check speakers that you are using on the
figure displayed in "Speaker Channels".
• If an item cannot be selected even though
connection is correct, check that the settings
in "Speaker Channels" matches the number of
connected channels.
Set whether speakers are connected to Zone 2 or
Zone 3 speaker terminals.
"Zone 2": When speakers are connected to Zone 2
speaker terminals
"Zone 2/Zone 3": When connecting speaker to both
ZONE 2 speaker terminal and ZONE 3 speaker
terminals.
• This setting cannot be selected under any of
following conditions.
– When the surround back speakers are used
– When 2 sets of height speakers are used
"No": When speakers are not connected to Zone 2
speaker terminals
• This setting cannot be selected when "Zone 2
Lineout" is set to "Zone B".
≫