Page 1 Foreword Congratulations on choosing a SUBARU vehicle. This Owner’s Manual has all the information necessary to keep your SUBARU in excellent condition and to properly maintain the emission control system for minimizing emission pollutants. We urge you to read this manual carefully so that you may understand your vehicle and its operation.
Page 2 This manual describes the following types of the Legacy series. 000138 1) Legacy Sedan 2) Legacy Station wagon 3) OUTBACK Sedan 4) OUTBACK Station wagon...
Page 4 Warranties Warranties for U.S.A. All SUBARU vehicles distributed by Subaru of America, Inc. and sold at retail by an authorized SUBARU dealer in the United States come with the following warranties: SUBARU Limited Warranty Emission Control Systems Warranty Emissions Performance Warranty...
Page 5: Safety Warnings
This chapter informs you how to keep your SUBARU looking good. Chapter 11: Maintenance and service This chapter informs you when you need to take your SUBARU to the dealer for scheduled maintenance and informs you how to keep your SUBARU running prop- erly.
Page 6: Vehicle Symbols
Vehicle symbols There are some of the symbols you may see on your vehicle. Mark Name CAUTION Passengers’ windows lock Fuel Front fog lights Parking lights Hazard warning flasher Cigarette lighter Seat heater Child restraint lower anchor- ages Mark Name Child restraint top tether an- chorages Horn...
Page 7: Seat, Seatbelt And Srs Airbags
Mark Name Washer Door lock (Transmitter) Door unlock (Transmitter) Trunk lid (Sedan) or rear gate (Station wagon) (Trans- mitter) Safety precautions when driving Seatbelt and SRS airbag All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Otherwise, the possibility of serious injury becomes greater in the event of a sudden stop or accident.
Page 8: Child Safety
Child safety Never hold a child on your lap or in your arms while the vehicle is moving. The passenger cannot protect the child from injury in a collision, because the child will be caught between the passenger and objects inside the vehicle. While riding in the vehicle, infants and small children should always be placed in the REAR seat in an...
Page 9: Drinking And Driving
Carefully read the sections “Child restraint systems”,“*SRS airbag (Supplemental Restraint System airbag)”, and “Seatbelts” in chapter 1 of this owner’s manual for in- structions and precautions concerning the child restraint system, seatbelt system and SRS airbag system. Engine exhaust gas (carbon monoxide) Never inhale engine exhaust gas.
Page 10: Driving With Pets
Drugs and driving There are some drugs (over the counter and prescription) that can delay your reaction time and impair your perception, judgment and at- tentiveness. If you drive after taking them, it may increase your, your passengers’ and other persons’ risk of being involved in a serious or fa- tal accident.
Page 11: California Proposition 65
driving. In a collision or sudden stop, unre- strained pets or cages can be thrown around inside the vehicle and hurt you or your passengers. Besides, the pets can be hurt under these situations. It is also for their own safety that pets should be prop- erly restrained in your vehicle.
Page 12: Table Of Contents
Table of contents Seat, seatbelt and SRS airbags Keys and doors Instruments and controls Climate control Audio Interior equipment Starting and operating Driving tips In case of emergency Appearance care Maintenance and service Specifications Consumer information and Reporting safety defects Index...
Page 13: Towing Hook (Page
Illustrated index Exterior Engine hood lock release (page 11-4) Headlight switch (page 3-31) Bulb replacement (page 11-49) Wiper switch (page 3-35) Moonroof (page 2-25) Roof rail (page 8-14) Door locks (page 2-4) Tire pressure (page 11-35) Flat tires (page 9-4) 10) Tire chains (page 8-11) 11) Fog light switch (page 3-34) 12) Tie-down hooks (page 9-13)
Page 14 000140 Rear window defogger button (page 3-38) Fuel filler lid and cap (page 7-4) Child safety locks (page 2-18) Tie-down hooks (page 9-13) Towing hook (page 9-13) Trunk lid (page 2-21) Rear gate (page 2-24) Bulb replacement (page 11-51) Rear wiper blade assembly and rub- ber replacement (page 3-37) –...
Page 15 Interior Passenger compartment area Lower anchorages for child restraint system (page 1-32) Seatbelt (page 1-11) Center console (page 6-5) Front seat (page 1-2) Rear seat (page 1-7) 000073...
Page 16 Top tether anchorages (page 1-36) Dome lights (page 6-2) Sun visors (page 6-3) Cargo area light (page 6-2) Rear center seatbelt (page 1-17) Cargo area cover (page 6-12) 000177 – CONTINUED –...
Page 17 14 13 12 11 10 9 4 5 6 7 Parking brake lever (page 7-35) Gear shift lever (MT) (page 7-9) Select lever (AT) (page 7-11) Information display (page 3-26) Clock (page 3-25) Dashboard storage compartment (page 6-4) Navigation system (if equipped) (See navigation system instruction manu- al.) Glove box (page 6-4)
Page 18 Instrument panel 2 3 4 5 6 000176 Door locks (page 2-4) Illumination brightness control (page 3-33) Remote control mirror (page 3-41) Windshield wiper deicer (page 3-38) Vehicle Dynamics Control OFF switch (page 7-32) Light control lever (page 3-31) Combination meter (page 3-5/page 3-10) Wiper control lever (page 3-34) Cruise control (page 7-36)
Page 19: Fog Light Switch (Page
Light control and wiper control levers/switches Parking light switch (page 3-33) Windshield wiper (page 3-34) Mist (page 3-36) Windshield washer (page 3-35) Rear window wiper and washer switch (page 3-37) Wiper control lever (page 3-35) Light control lever (page 3-31) Fog light switch (page 3-34) Headlight ON/OFF (page 3-31) 10) Headlight flasher High/Low beam...
Page 20 Combination meter U.S.-spec. vehicles 000141 Temperature gauge (page 3-9/page 3-13) Tachometer (page 3-8/page 3-12) Speedometer (page 3-6/page 3-10) Fuel gauge (page 3-8/page 3-12) Trip meter A/B selection and trip meter reset knob (page 3-7/page 3- Trip meter and odometer (page 3-7/ page 3-11) Selector lever position indicator (page 3-24)
Page 21 Canada-spec. vehicles 000142 Temperature gauge (page 3-9/page 3-13) Tachometer (page 3-8/page 3-12) Speedometer (page 3-6/page 3-10) Fuel gauge (page 3-8/page 3-12) Trip meter A/B selection and trip meter reset knob (page 3-7/page 3- Trip meter and odometer (page 3-7/ page 3-11) Selector lever position indicator (page 3-24) Gear position indicator (page 3-24)
Page 22 Warning and indicator light Mark Name Page Seatbelt warning light 3-14 Front passenger’s 3-14 seatbelt warning light SRS airbag system 3-16 warning light CHECK ENGINE warning light/Malfunc- 3-17 tion indicator lamp Charge warning light 3-18 Oil pressure warning 3-18 light AT OIL temperature warning light (if 3-18...
Page 23 Trunk/cargo area 000147 Jack handle (page 9-18) Jack (page 9-18) Spare tire (page 9-2)
Page 24 A SUBARU dealer can change the settings of the functions shown in the following table to meet your personal requirements. Contact the nearest SUBARU dealer for details. If your vehicle is equipped with navigation system, the settings for some of these functions can be changed using the monitor.
Page 26 ... 1-38 Vehicle with SRS airbags and lap/shoulder restraints for driver, front passenger, and window-side rear passengers ... Subaru advanced frontal airbag system ... 1-10 SRS side airbag and SRS curtain airbag ... 1-10 SRS airbag system monitors ...
Page 27: Seat, Seatbelt And Srs Airbags
Seat, seatbelt and SRS airbags Front seats Seat, seatbelt and SRS airbags Never adjust the seat while driv- ing to avoid the possibility of loss of vehicle control and of personal injury. Before adjusting the seat, make sure the hands and feet of rear seat passengers are clear of the adjusting mechanism.
Page 28: Manual Seat
NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. According to accident statistics, children are safer when properly re- strained in the rear seating posi- tions than in the front seating posi- tions.
Page 29: Power Seat (If Equipped)
Seat, seatbelt and SRS airbags The seatback placed in a reclined position can spring back upward with force when released. When operating the reclining le- ver to return the seatback, hold it lightly so that it may be raised back gradually. Seat cushion height adjustment (driver’s seat) 100246...
Page 30: Head Restraint Adjustment
100250 To adjust the angle of the seatback, move the control switch. Seat cushion angle adjustment (Driver’s seat only) 100248 To adjust the seat cushion angle, pull up or push down the front end of the control switch. Seat height adjustment (Driver’s seat only) 100249 To adjust the seat height, pull up or push...
Page 31: Active Head Restraint
If your vehicle is involved in a rear-end collision, have an autho- rized SUBARU dealer inspect the active head restraints. The active head restraints may not operate in the event the vehi- cle experiences only a slight im- pact in the rear.
Page 32: Seat Heater (If Equipped)
Seat heater (if equipped) 100661 The seat heater operates when the igni- tion switch is either in the “ACC” or “ON” position. Each seat heater has four levels of adjust- ment. To use the heater in the right-hand seat, turn the “R” adjustment knob forward until the “...
Page 33: Folding Down The Rear Seat - Station Wagon
Seat, seatbelt and SRS airbags 100094 Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or accident. Folding down the rear seat – Station wagon After returning the rear seat to its original position, be certain to...
Page 34 Rear windows side seating position The head restraint is not intended to be used at the lowest position. Be- fore sitting on the seat, raise the head restraint to an appropriate po- sition depending on your sitting height. 200290 Sedan 200284 Station wagon To raise the head restraint, pull it up.
Page 35: Armrest (If Equipped)
1-10 Seat, seatbelt and SRS airbags head restraint to improve rearward visibil- ity. Armrest (if equipped) 200291 Sedan 200286 Station wagon To lower the armrest, pull on the top edge of the armrest. To avoid the possibility of serious injury, passengers must never be al- lowed to sit on the center armrest while the vehicle is in motion.
Page 36: Seatbelts
Secure long objects properly to prevent them from shooting for- ward and causing serious injury during a sudden stop or sharp cornering. Tie long objects down with a rope or something equiva- lent. Avoid loading objects longer than 6.6 ft (2 m) and heavier than 55 lbs (25 kg).
Page 37: Emergency Locking Retractor (Elr)
1-12 Seat, seatbelt and SRS airbags NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. According to accident statistics, children are safer when properly restrained in the rear seating posi- tions than in the front seating po-...
Page 38: Automatic/Emergency Locking Retractor (A/Elr)
Automatic/Emergency Lock- ing Retractor (A/ELR) Each passenger’s seatbelt has an Auto- matic/Emergency Locking Retractor (A/ ELR). The Automatic/Emergency Locking Retractor normally functions as an Emer- gency Locking Retractor (ELR). The A/ ELR has an additional locking mode “Au- tomatic Locking Retractor (ALR) mode” in- tended to secure a child restraint system.
Page 39 (Models equipped with manual seats only) If the seatbelt warning device for front passenger’s seat still does not function correctly after taking relevant corrective actions described above, immediately contact your SUBARU dealer for an in- spection.
Page 40: Fastening The Seatbelt
Fastening the seatbelt Never use a belt that is twisted or reversed. In an accident, this can increase the risk or severity of in- jury. Keep the lap belt as low as possi- ble on your hips. In a collision, this spreads the force of the lap belt over stronger hip bones in- stead of across the weaker abdo-...
Page 41 1-16 Seat, seatbelt and SRS airbags 100102 4. Insert the tongue plate into the buckle until you hear a click. 100103 5. To make the lap part tight, pull up on the shoulder belt. 6. Place the lap belt as low as possible on your hips, not on your waist.
Page 42 Rear seatbelts (except rear center seatbelt on Station wagon) 1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly.
Page 43 1-18 Seat, seatbelt and SRS airbags 100108 Fastening the seatbelt with the web- bing twisted can increase the risk or severity of injury in an accident. When fastening the belt after it is pulled out from the retractor, espe- cially when inserting the connec- tor’s tongue plate into the mating buckle (on right-hand side), always check that the webbing is not twist-...
Page 44 100735 2. Pull out the seatbelt slowly from the overhead retractor. 100309 3. After confirming that the webbing is not twisted, insert the connector (tongue) at- tached at the webbing end into the buckle on the right-hand side until a click is heard. If the belt stops before reaching the buck- le, return the belt slightly and pull it out more slowly.
Page 45 1-20 Seat, seatbelt and SRS airbags low as possible on your hips, not on your waist. Unfastening the seatbelt 100116 Push the release button of the center seatbelt buckle (on the left-hand side) to unfasten the seatbelt. 100381 100382 1. Insert a key or other hard pointed ob- ject into the slot in the connector (buckle) on the right-hand side and push it in, and the connector (tongue) plate will discon-...
Page 46: Seatbelt Maintenance
100736 Do not allow the retractor to roll up the seatbelt too quickly. Other- wise, the metal tongue plates may hit against the trim, resulting in damaged trim. Have the seatbelt fully rolled up so that the tongue plates are neat- ly stored.
Page 47: System Monitors
If either front seatbelt does not re- tract or cannot be pulled out due to a malfunction or activation of the preten- sioner, contact your SUBARU dealer as soon as possible. If the front seatbelt retractor assem- bly or surrounding area has been dam- aged, contact your SUBARU dealer as soon as possible.
Page 48: System Servicing
SRS airbag sys- tem. Immediately take your vehicle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g.
Page 49: Precautions Against Vehicle Modification
NOTE If the front part of the vehicle is dam- aged in an accident to the extent that the seatbelt pretensioner does not op- erate, contact your SUBARU dealer as soon as possible. Precautions against vehicle modification Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle.
Page 50: Child Restraint Systems
Child restraint systems 100124 Infants and small children should always be placed in an infant or child restraint system in the rear seat while riding in the vehicle. You should use an infant or child restraint system that meets Federal Motor Vehicle Safety Standards or Canada Mo- tor Vehicle Safety Standards, is compati- ble with your vehicle and is appropriate for...
Page 51: Where To Place A Child Restraint System
Where to place a child re- straint system The following are SUBARU’s recommen- dations on where to place a child restraint system in your vehicle. 100127 A: Front passenger’s seat...
Page 52: Choosing A Child Restraint System
Put children aged 12 and under in the rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or improperly restrained.
Page 53: Installing Child Restraint Systems With A/Elr Seatbelt
1-28 Seat, seatbelt and SRS airbags Installing child restraint sys- tems with A/ELR seatbelt Child restraint systems and seat- belts can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in Do not leave an unsecured child restraint system in your vehicle.
Page 54 100505 6. Push and pull the child restraint system forward and from side to side to check if it is firmly secured. Sometimes a child restraint can be more firmly secured by pushing it down into the seat cushion and then tightening the seat- belt.
Page 55 1-30 Seat, seatbelt and SRS airbags 100137 4. Take up the slack in the lap belt. 5. Pull out the seatbelt fully from the re- tractor to change the retractor over from the Emergency Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) function.
Page 56: Installing A Booster Seat
er anchor and tighten the top tether. See the “Top tether anchorages” for additional instructions. 100140 9. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract com- pletely. The belt will return to the ELR mode.
Page 57: Installation Of Child Restraint Systems By Use Of Lower And Tether Anchorages (Latch)
1-32 Seat, seatbelt and SRS airbags following the instructions provided by its manufacturer. 3. Insert the tongue plate into the buckle until you hear a click. Take care not to twist the seatbelt. Make sure the shoulder belt is positioned across the center of child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips.
Page 58 When you install a child restraint system, follow the manufacturer’s instructions supplied with it. After installing the child restraint system, check to ensure that it is held se- curely in position. If it is not held tight and secure, the danger of your child suffering personal injury in the event of an accident may be in- creased.
Page 59 1-34 Seat, seatbelt and SRS airbags TOP TETHER 100269 Station wagon The tether anchorages (upper anchorag- es) are provided for all the seating posi- tions (middle and both window-side ones) of the rear seat. 100653 Sedan 100654 Station wagon You will find marks “ ”...
Page 60 the seat cushion and seatback a little wid- er to locate the two anchorages (bars) for the position where you want to install the child restraint system. 100655 Station wagon: Remove the two covers from the selected side of the rear seat- back to expose the anchorages (bars) to be used for installation of the child re- straint system.
Page 61: Top Tether Anchorages
If you have any question concerning this type of child restraint system, ask your SUBARU dealer. Top tether anchorages Your vehicle is equipped with three top tether anchorages so that a child restraint system having a top tether can be in- stalled in the rear seat.
Page 62 To hook the top tether Sedan 200290 1. Remove the head restraint at the seat- ing position where the child seat has been installed with the seatbelt or lower anchor- ages; lift up the head restraint while press- ing the release button. Store the head restraint in the trunk.
Page 63: Srs Airbag (Supplemental Restraint System Airbag)
1-38 Seat, seatbelt and SRS airbags lower anchorages; lift up the head re- straint while pressing the release button. Store the head restraint in the cargo area. Avoid placing the head restraint in the passenger compartment to prevent it from being thrown around in the passenger compartment in a sudden stop or a sharp turn.
Page 64 senger, and window-side rear passen- gers) These SRS airbags are designed only as a supplement to the primary protec- tion provided by the seatbelt. The system also controls front seatbelt pretensioners. For operation instructions and precautions concerning the seatbelt pretensioner, see the “Front seatbelt pre- tensioners”...
Page 65 1-40 Seat, seatbelt and SRS airbags 100082 Put children aged 12 and under in the rear seat properly restrained at all times. The SRS airbag de- ploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or improperly re- strained.
Page 66 Components 18 19 Sedan 100669 1-41 Seat, seatbelt and SRS airbags 1) Airbag control module (including impact sensors) 2) Frontal airbag module (driver’s side) 3) Frontal airbag module (front passen- ger’s side) 4) Front sub sensor (left-hand side) 5) Front sub sensor (right-hand side) 6) Side airbag module (driver’s side) 7) Side airbag module (front passenger’s side)
Page 67 1-42 Seat, seatbelt and SRS airbags Station wagon 18 19 1) Airbag control module (including impact sensors) 2) Frontal airbag module (driver’s side) 3) Frontal airbag module (front passen- ger’s side) 4) Front sub sensor (left-hand side) 5) Front sub sensor (right-hand side) 6) Side airbag module (driver’s side) 7) Side airbag module (front passenger’s side)
Page 68: Subaru Advanced Frontal Airbag System
Subaru advanced frontal air- bag system Your vehicle is equipped with a Subaru advanced frontal airbag system that com- plies with the new advanced frontal airbag requirements in the amended Federal Mo- tor Vehicle Safety Standard (FMVSS) No. 208. The Subaru advanced frontal airbag sys- tem automatically determines the deploy- ment force of the driver’s SRS frontal air-...
Page 69 1-44 Seat, seatbelt and SRS airbags 100125 Never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can in- jure or even kill the child. 100155 The SRS airbag deploys with con- siderable speed and force.
Page 70 SRS frontal airbag even when the driver’s SRS frontal airbag deploys. This is normal. Observe the following precautions. Failure to do so may prevent the Subaru ad- vanced frontal airbag system from func- tioning correctly or cause the system to fail.
Page 71 Have your vehicle inspected at your SUBARU dealer. NOTE The front passenger’s SRS side airbag, SRS curtain airbag and seatbelt preten- sioner are not controlled by the Subaru advanced frontal airbag system. Passenger’s frontal airbag ON and OFF indicators 100663 : Front passenger’s frontal air-...
Page 72 Conditions in which front passen- ger’s SRS frontal airbag is not acti- vated The front passenger’s SRS frontal airbag will not be activated when any of the fol- lowing conditions are met regarding the front passenger’s seat: The seat is empty. The seat is equipped with a rearward facing child restraint system and an infant is restrained with it.
Page 73 SUBARU dealer for an inspection. NOTE When a child who has outgrown a child restraint system or a small adult is seated in the front passenger’s seat,...
Page 74 Subaru advanced air- bag system. If you have any questions, you may contact the following Subaru dis- tributors: <Continental U.S., Alaska and the District...
Page 75 2) Passenger’s side The SRS airbag can function only when the ignition switch is in the “ON” position. The Subaru advanced frontal airbag sys- tem is designed to determine the activa- tion or deactivation condition of the front passenger’s SRS frontal airbag depend- ing on the total load on the front passen- ger’s seat monitored by the front passen-...
Page 76 Do not touch the SRS airbag system components around the steering wheel and dashboard with bare hands right after deployment. Doing so can cause burns because the components can be very hot as a re- sult of deployment. The driver’s SRS frontal airbag and front passenger’s SRS frontal airbag are de- signed to deploy in the event of an acci- dent involving a moderate to severe fron-...
Page 77 1-52 Seat, seatbelt and SRS airbags frontal airbags may be activated when the vehicle sustains a hard impact in the un- dercarriage area from the road surface (such as when the vehicle plunges into a deep ditch, is severely impacted or knocked hard against an obstacle on the road such as a curb).
Page 78: Srs Side Airbag And Srs Curtain Airbag
Examples of the types of accidents in which the driver’s/driver’s and front passenger’s SRS frontal air- bag(s) will basically not deploy. 100279 The driver’s and front passenger’s SRS frontal airbags are designed basically not to deploy if the vehicle is struck from the side or from behind, or if it rolls onto its side or roof, or if it is involved in a low- speed frontal collision.
Page 79 1-54 Seat, seatbelt and SRS airbags The SRS side airbag and SRS cur- tain airbag are designed as only a supplement to the primary protec- tion provided by the seatbelt. They do not do away with the need to fas- ten seatbelts.
Page 80 Never allow a child to kneel on the front passenger’s seat facing the side window or to wrap his/her arms around the front seat seat- back. In the event of an accident, the force of the SRS side airbag deployment could injure the child seriously because his/her head or arms or other parts of the body are too close to the SRS side air-...
Page 81 1-56 Seat, seatbelt and SRS airbags Do not attach a hands-free micro- phone or any other accessory to a front pillar, a center pillar, a rear pillar, the windshield, a side win- dow, an assist grip, or any other cabin surface that would be near a deploying SRS curtain airbag.
Page 82 senses an impact force above a predeter- mined level in a side collision, the control module causes both the SRS side airbag and curtain airbag on the impacted side to inflate regardless of whether the rear wheel house impact sensor on the same side senses an impact.
Page 83 1-58 Seat, seatbelt and SRS airbags Examples of the types of accidents in which the SRS side airbag and SRS cur- tain airbag are unlikely to deploy. The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment.
Page 84: Srs Airbag System Monitors
Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag will basically not deploy. 100659 1) The vehicle is involved in frontal collision with another vehicle (moving or station- ary). 2) The vehicle is struck from behind. The SRS side airbag and SRS curtain air- bag are basically not designed to deploy if the vehicle is involved in a frontal collision...
Page 85: Srs Airbag System Servicing
SRS airbag sys- tem. Immediately take your vehicle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g.
Page 86: Precautions Against Vehicle Modification
In the event that the SRS airbag is de- ployed, replacement of the system should be performed only by an autho- rized SUBARU dealer. When the com- ponents of the SRS airbag system are replaced, use only genuine SUBARU parts.
Page 87 Owner’s Manual. Attachment of any equipment (side steps or side sill protectors, etc.) other than genuine SUBARU accessory parts to the side body. Always consult your SUBARU dealer if you want to install any accessory parts on your vehicle.
Page 88: Keys And Doors
Keys ... Key number ... Immobilizer ... Security ID plate ... Security indicator light ... Key replacement ... Door locks ... Locking and unlocking from the outside ... Locking and unlocking from the inside ... Battery drainage prevention function ... Power door locking switches ...
Page 89: Keys
Keys and doors Keys 200700 1) Master key 2) Submaster key 3) Valet key 4) Key number plate 5) Security ID plate Three types of keys are provided for your vehicle. Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle.
Page 90: Immobilizer
Immobilizer The immobilizer system is designed to prevent an unauthorized person from starting the engine. Only keys registered with your vehicle’s immobilizer system can be used to operate your vehicle. Even if an unregistered key fits into the ignition switch and can be turned to the “START” position, the engine will automatically stop after several seconds.
Page 91: Security Indicator Light
If the security indicator light does not flash, the immobilizer system may be faulty. If this occurs, contact your SUBARU dealer as soon as possible. In case an unauthorized key is used (e.g. an imitation key), the security indicator light comes on.
Page 92: Locking And Unlocking From The Inside
200837 Locking without the key 1) Rotate the lock lever rearward. 2) Close the door. To lock the door from the outside without the key, rotate the lock lever rearward and then close the door. 200838 Locking without the key 1) Push the power door locking switch for- ward.
Page 93: Battery Drainage Prevention Function
10 minutes of illumination to prevent the battery from going dead. The operational/non-operational setting of this function can be changed by a SUBARU dealer. Contact the nearest SUBARU dealer if you would like to change the set- ting.
Page 94: Key Lock-In Prevention Function
If the spare key is used to lock the driv- er’s door from the outside of the vehicle, the door is locked. This function’s operative/non-operative setting can be changed by a SUBARU dealer. Contact a SUBARU dealer for de- tails. NOTE...
Page 95: Locking The Doors
Keys and doors hicle. The keyless entry system has the follow- ing functions. Locking and unlocking the doors (and rear gate on the Station wagon) without a Locking and unlocking the doors (and trunk lid on the Sedan) without key Unlocking the rear gate on the Station wagon without key Unlocking the trunk lid on the Sedan...
Page 96: Unlocking The Doors
The interior light must be set to the middle position in order for this function to operate. A SUBARU dealer can change the illumi- nation period setting of the interior light in accordance with your preference. Contact the nearest SUBARU dealer for details.
Page 97: Sounding A Panic Alarm
5. The turn signal lights flash 3 times to in- dicate completion of the setting. You may have the above settings done by your SUBARU dealer. Replacing the battery Do not let dust, oil or water get on or in the transmitter when replacing the battery.
Page 98: Replacing Lost Transmitters
200717 1) Negative (–) side facing up 3. Replace with a new battery (Type CR2025 or equivalent) making sure to in- stall the new battery with the negative (–) side facing up. 4. Refit the removed half of the transmit- ter case.
Page 99 2-12 Keys and doors 200840 1) Open and close the driver’s door once. 200721 1) LOCK 2) ON 2) Insert the key into the ignition switch, then turn it from the “LOCK” position to the “ON” position 10 times within 15 seconds.
Page 100 onds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3. 200842 6. When you have finished entering the number, pull the lock knob to the “UN- LOCK”...
Page 101: Alarm System
You can set the system for de- activation yourself or have it done by your SUBARU dealer. System alarm operation The alarm system will give the following alarms when triggered: The vehicle’s horn will sound and the...
Page 102: If You Have Accidentally Triggered The Alarm System
“AL on” and the horn sounds once, indi- cating that the system is now activated. NOTE You may have the above setting change done by your SUBARU dealer. If you have accidentally trig- gered the alarm system To stop the alarm...
Page 103: Disarming The System
The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer. If your vehicle is a Sedan and you un- lock the trunk using the remote trans- mitter’s “...
Page 104: Passive Arming
DOORS MUST BE MANUALLY LOCKED. To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer. Arming the system In passive mode, the system will au-...
Page 105: Tripped Sensor Identification
30 seconds. If you desire, your SUBARU dealer can connect them and set them for activation or deactivation. NOTE...
Page 106: Windows
Windows Power windows To avoid serious personal injury caused by entrapment, you must do the following. When operating the power win- dows, be extremely careful to pre- vent anyone’s fingers, arms, neck or head from being caught in the window. Always lock the passengers’...
Page 107 2-20 Keys and doors 200845 To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. Operating the passengers’ windows 200846 To open the passengers’ windows, push the appropriate switch down and hold it until the window reaches the desired posi- tion.
Page 108: Trunk Lid (Sedan)
Passengers’ side switches 200848 Front passenger’s window switch 1) Open 2) Close To open the window, push the switch down and hold it until the window reaches the desired position. 200849 Rear passengers’ window switches 1) Open 2) Close To close the window, pull the switch up and hold it until the window reaches the desired position.
Page 109: To Open The Trunk Lid From Inside
2-22 Keys and doors trunk lid down until the latch engages. NOTE Do not leave your valuables in the trunk when you leave your vehicle. To open the trunk lid from in- side 200850 Pull the trunk lid release lever upward. To lock and unlock the trunk lid release lever 200851...
Page 110 Never allow any child to get in the trunk and play with the release han- dle. If the driver starts the vehicle without knowing that a child is in- side the trunk and the child opens the lid using the release handle, the child could fall out and be killed or seriously injured.
Page 111: Rear Gate (Station Wagon)
2-24 Keys and doors SUBARU dealer. In that case, use the key to release the latch, then close the trunk lid. Also, if the movement of the release han- dle feels restricted or not entirely smooth during operation, or the handle and/or handle base is cracked, contact your SUBARU dealer.
Page 112: Moonroof (If Equipped)
Do not jam a plastic bag in or place cellophane tape on the rear gate stays or scratch the stays while loading or unloading cargo. That could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.
Page 113: Tilting/Sliding Moonroof (Sedan)
2-26 Keys and doors Tilting/sliding moonroof (Se- dan) Tilt function 200856 1) Tilt up 2) Tilt down The tilting function will only operate when the moonroof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt”...
Page 114: Moonroof (Station Wagon)
NOTE For the sake of safety, it is recommend- ed that you avoid driving with the moonroof fully opened. Sun shades 200404 The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.
Page 115 2-28 Keys and doors switch to the “CLOSE” side then quickly release it. The rear moonroof will stop at a position approximately 5.9 in (15 cm) before its ful- ly closed position. After confirming safety, pull the switch to the “CLOSE” side again and quickly release it.
Page 116: Instruments And Controls
Ignition switch ... LOCK ... ACC ... ON ... START ... Key reminder chime ... Ignition switch light ... Hazard warning flasher ... Meters and gauges (Turbo models) ... Combination meter illumination ... Canceling the function for meter/gauge needle movement and combination meter sequential illumination upon turning on the ignition switch ...
Page 117 Instruments and controls Cruise control set indicator light ... Headlight indicator light ... Front fog light indicator light ... Clock ... 3-25 Information display (Vehicle without Navigation System) ... 3-26 Outside temperature indicator ... Current fuel consumption ... Average fuel consumption ... Driving range on remaining fuel ...
Page 118: Ignition Switch
Ignition switch Instruments and controls Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, prevent- ing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
Page 119: Acc
Instruments and controls Manual transmission vehicles 300591 The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it. In this position the electrical accessories (radio, accessory power outlet, etc.) can be used. This is the normal operating position after the engine is started.
Page 120: Key Reminder Chime
Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is removed from the ignition switch. Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light comes on when any of the doors are opened.
Page 121: Speedometer
Instruments and controls Canceling the function for meter/gauge needle move- ment and combination meter sequential illumination upon turning on the ignition switch 300185 It is possible to activate or deactivate the movement of the meter needles and gauge needles and sequential illumination of the combination meter that take place when the ignition switch is turned to the “ON”...
Page 122: Odometer
Odometer 300261 This meter displays the odometer when the ignition switch is in the “LOCK”, “ACC” or “ON” position. The odometer shows the total distance that the vehicle has been driven. If you press the trip knob when the ignition switch is in the “LOCK”...
Page 123: Fuel Gauge
“ ”. If the trip meter shows “ ”, immedi- ately contact the nearest SUBARU dealer and have the vehicle communication sys- tem inspected. NOTE If you press the trip knob while the trip meter is showing “...
Page 124: Temperature Gauge
“LOCK” position and back to the “ON” po- sition, the rim will again flash five times. NOTE 200253 You will see the “ ” sign in the fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.
Page 125: Meters And Gauges (Non-Turbo Models)
3-10 Instruments and controls Meters and gauges (Non-tur- bo models) NOTE Liquid-crystal displays are used in some of the meters and gauges in the combination meter. You will find their indications hard to see if you wear po- larized glasses. Combination meter illumina- tion When the ignition switch is turned to the...
Page 126: Odometer
Odometer 300261 This meter displays the odometer when the ignition switch is in the “LOCK”, “ACC” or “ON” position. The odometer shows the total distance that the vehicle has been driven. If you press the trip knob when the ignition switch is in the “LOCK”...
Page 127: Tachometer
“ ”. If the trip meter shows “ ”, immediate- ly contact the nearest SUBARU dealer and have the vehicle communication sys- tem inspected. NOTE If you press the trip knob while the trip meter is showing “...
Page 128: Temperature Gauge
door, the fuel gauge needle will drop to the “E” position and the dial, needle, and rim will go off. NOTE 200253 You will see the “ ” sign in the fuel gauge. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.
Page 129: Warning And Indicator Lights
: Cruise control set indicator light (if equipped) If any lights fail to come on, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair. Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning device at the driver’s and front...
Page 130 100254 Driver’s warning light 100662 Front passenger’s warning light Operation If the driver and/or front passenger have/ has not yet fastened the seatbelt(s) when the ignition switch is turned to the “ON” po- sition, the seatbelt warning light(s) will flash for 6 seconds, to warn that the seat- belt(s) is/are unfastened.
Page 131: Srs Airbag System Warning Light
If still the seatbelt warning device for front passenger’s seat does not function cor- rectly after taking relevant corrective ac- tions described above, immediately con- tact your SUBARU dealer for an inspec- tion. SRS airbag system warning light When the ignition switch is turned to the “ON”...
Page 132: Front Passenger's Frontal Airbag On And Off Indicators
ON indicator will remain extinguished while the OFF indicator will illuminate. If both the ON and OFF indicators remain lit or extinguished simultaneously, the sys- tem is faulty. Contact your SUBARU deal- er immediately for an inspection. 3-17 Instruments and controls...
Page 133: Charge Warning Light
If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately. AT OIL TEMPerature warning light (AT vehi-...
Page 134 Should the warning light flash, have the system inspected your nearest SUBARU dealer as soon as possible. If this light does not come on briefly after the ignition switch is turned ON or the light is flashing, you should have your Tire Pressure...
Page 135: Abs Warning Light
Brake system (U.S.) warning light (Canada) Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately.
Page 136: Low Fuel Warning Light
If the fluid level is below the “MIN” mark in the reser- voir, do not drive the vehicle. Have the ve- hicle towed to the nearest SUBARU deal- er for repair. Electronic Brake Force Distribution...
Page 137: Door Open Warning Light
The Vehicle Dynamics Control system is probably faulty under any of the following conditions. Have your vehicle checked at a SUBARU dealer immediately. The light does not come on when the ig- nition switch is turned to the “ON” position.
Page 138: Vehicle Dynamics Control Warning Light
You will be safe while driving with this condition, but have your vehicle checked at a SUBARU dealer as soon as possible. NOTE If the warning light behavior is as...
Page 139: Sport Mode Indicator Light (At Vehicles)
Instruments and controls chapter 2.) If the indicator light does not flash, it may indicate that immobilizer system may be faulty. Contact your nearest SUBARU dealer immediately. In the event that an unauthorized key (for example, an unauthorized duplicate) is...
Page 140: High Beam Indicator Light
possible. Refer to the “Replacing bulbs” section in chapter 11. High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated. Cruise control indica- tor light The cruise control indicator light comes on when the ignition switch is turned to the...
Page 141: Information Display
3-26 Instruments and controls 300599 To adjust the time shown by the clock, press the “+” button or the “–” button. The indicated time will change in one-minute increments. If you keep the button pressed, the rate at which the indicated time changes will speed up.
Page 142: Outside Temperature Indicator
Outside Current Average tempera- fuel con- fuel con- ture sumption sumption Journey time Driving range on remaining fuel Outside temperature indica- 300594 U.S.-spec. vehicles 300267 Canada-spec. vehicles The outside temperature indicator shows the outside temperature in a range from – 22 to 122°F (–30 to 50°C).
Page 143: Current Fuel Consumption
3-28 Instruments and controls When the outside temperature drops to 37°F (3°C) or lower, the temperature indi- cation flashes to show that the road sur- face may be frozen. If the outside temperature drops to 37°F (3°C) or lower while the display is giving an indication other than the outside tem- perature, the display switches to the out- side temperature indication and flashes...
Page 144: Driving Range On Remaining Fuel
300597 Canada-spec. vehicles This indication shows the average rate of fuel consumption since the trip meter was last reset. Pressing the trip knob toggles the indica- tion between the average fuel consump- tion corresponding to the A trip meter indi- cation and the average fuel consumption corresponding to the B trip meter indica- tion.
Page 145: Journey Time
3-30 Instruments and controls 300275 U.S.-spec. vehicles 400265 Canada-spec. vehicles If the driving range is shown as “ there is only a tiny amount of fuel left in the tank. You must refuel the vehicle immedi- ately. NOTE The driving range on remaining fuel is only a guide.
Page 146: Light Control Switch
Light control switch To prevent battery discharge result- ing from accidentally leaving your lights on when your vehicle is parked, the light switch operates only when the ignition switch is in the “ON” position. In any other posi- tion, the vehicle’s lights will be out. If you park your vehicle on a road- side at night, use the hazard warn- ing flasher to alert the other drivers.
Page 147: Headlight Flasher
3-32 Instruments and controls Headlight flasher 300508 Do not hold the lever in the flashing position for more than just a few seconds. To flash the headlights, pull the lever to- ward you and then release it. The high beam will stay on for as long as you hold the lever.
Page 148: Illumination Brightness Control
Illumination brightness con- trol 300510 The brightness of clock display, audio, air conditioner, information display and in- strument panel illumination dims when the light switch is in the “ ” or “ ” po- sitions. You can adjust brightness of the instrument panel illumination for better visibility.
Page 149: Front Fog Light Switch (If Equipped)
3-34 Instruments and controls Front fog light switch (if equipped) 300512 The front fog lights operate only when the light switch is in the “ ” position. However, the front fog lights turn off when the headlights are switched to high beam. To turn on the front fog lights, turn the front fog light switch on the turn signal lever up- ward to the “...
Page 150: Windshield Wiper And Washer Switches
Use clean water if windshield washer fluid is unavailable. In ar- eas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle...
Page 151 3-36 Instruments and controls Windshield wipers 300286 OFF: Park : Intermittent LO: Low speed HI: High speed To turn the wipers on, push the wiper con- trol lever down. To turn the wipers off, return the lever to the “OFF” position. Mist (for a single wipe) 300288 For a single wipe of the wipers, pull the le-...
Page 152: Rear Window Wiper And Washer Switch (Station Wagon)
Washer 300289 To wash the windshield, push the washer button at the end of the wiper control le- ver. The washer fluid sprays until you re- lease the washer button. The wipers oper- ate while you push the button. Rear window wiper and wash- er switch (Station wagon) 300290 : Washer (accompanied by wiper opera-...
Page 153: Windshield Wiper Deicer (If Equipped)
“ACC” or “LOCK” position. If deicing is not complete, you have to push the button to turn the deicer on again. Your SUBARU dealer can set your wind- shield wiper deicer for continuous opera- tion. Contact your SUBARU dealer for de- tails.
Page 154 “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again. Your SUBARU dealer can set your rear window defogger for continuous opera- tion. Contact your SUBARU dealer for de- tails.
Page 155: Mirrors
3-40 Instruments and controls Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving. Inside mirror 300293 The inside mirror has a day and night po- sition. Pull the tab at the bottom of the mir- ror toward you for the night position.
Page 156: Outside Mirrors
cover the sensors with stickers, or other similar items. Periodically wipe the sen- sors clean using a piece of dry soft cotton cloth or an applicator. Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut.
Page 157 3-42 Instruments and controls when the ignition switch is in the “ON” or “ACC” position. 1. Turn the knob to the “L” side to adjust the left-hand mirror or to the “R” side to ad- just the right-hand mirror. 2. Move the knob in the direction you want to move the mirror.
Page 158 Tilt steering wheel Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and re- sult in personal injury. 300295 1. Adjust the seat position. Refer to the “Front seats” section (chapter 1). 2.
Page 160 Climate control Ventilator ... Air flow selection ... Center and side ventilators ... Manual climate control system (if equipped) ... Control panel ... Heater operation ... Air conditioner operation ... Automatic climate control system (if equipped) ... Control panel ... Temperature sensors ...
Page 161: Climate Control
Climate control Ventilator Climate control Air flow selection 400341...
Page 162: Center And Side Ventilators
Center and side ventilators Center ventilators 400343 Move the tab up and down or right and left to adjust the flow direction. Side ventilators 400578 1) Open 2) Close Move the tab up and down or right and left to adjust the flow direction. To open the ventilator, turn the side grille open/close wheel upward to the “...
Page 163 Climate control Temperature control dial 400346 This dial regulates the temperature of air flow from the air outlets over a range from the blue side (cool) to red side (warm). Fan speed control dial 400347 The fan operates only when the ignition switch is turned to the “ON”...
Page 164: Heater Operation
Air conditioner button 400349 The air conditioner operates only when the engine is running. Push the air conditioner button while the fan is in operation to turn on the air condi- tioner. The indicator light will come on. Push it again to turn off the air conditioner. Air inlet selection button 400350 ON position (Recirculation): Interior air is...
Page 165 Climate control tion is automatically set to “outside air” mode. In this state, you cannot select “recir- culation” mode by manually pressing the air inlet selection button. Also, you cannot stop the air condi- tioner compressor by pressing the air conditioner button.
Page 166: Air Conditioner Operation
When driving on a dusty road, set the air inlet control button to the ON position. Continued operation in the ON posi- tion may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
Page 167: Control Panel
Climate control Control panel 400580 1) AUTO button 2) Temperature control dial (driver’s side) 3) Defroster button 4) Temperature control dial (passenger’s side) 5) Rear window defogger button (Refer to the “Rear window defogger button” sec- tion in chapter 3.) 6) Air conditioner button 7) Air flow mode selection button 8) Fan speed control button...
Page 168 Temperature control dial 400583 Driver’s side 400584 Passenger’s side It is possible to make separate tempera- ture settings for the driver’s side and pas- senger’s side. Each temperature setting is shown on the display. With the dial set at your desired temperature, the system au- tomatically adjusts the temperature of air supplied from the outlets such that the de- sired temperature is achieved and main-...
Page 169 4-10 Climate control The fan speed is shown by the display. A/C – Air conditioner button 400586 If the windshield starts to fog when the cli- mate control system is operated in the AUTO mode, push the air conditioner but- ton “A/C”...
Page 170: Temperature Sensors
automatically. (There is one exception: When the temperature control dial is turned fully counterclockwise, the recircu- lation mode is automatically selected.) When the outside air mode is selected, a “ ” indicator light appears on the display. Continued operation in the “ ”...
Page 171: Operating Tips For Heater And Air Conditioner
Checking air conditioning system before summer sea- Check the air conditioner unit for refriger- ant leaks, hose conditions, and proper op- eration each spring. Have your SUBARU dealer perform this check. Cooling and dehumidifying in high humidity and low tem-...
Page 172: Air Filtration System (If Equipped)
SUBARU air filter kit. Replacement schedule: Every 12 months or 9,300 miles (15,000 km) whichever comes first Contact your SUBARU dealer if the following occurs, even if it is not yet time to change the filter: – Reduction of the air flow through the vents.
Page 174 Antenna system ... Printed antenna ... FM reception ... Installation of accessories ... Audio set ... Type A audio set ... Type B audio set ... Type C audio set ... Type A audio set (if equipped) ... Radio operation ... Compact disc player operation ...
Page 175: Antenna System
If reception continues to be unsatis- factory, switch to a stronger station. Installation of accessories Always consult your SUBARU dealer be- fore installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control...
Page 176: Audio
Audio set Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating de- tails. Type A audio set P-201UN PUSH POWER-VOL AUDIO SEEK TUNE SCAN TRACK 500224 Radio operation: refer to page 5-5...
Page 177: Type A Audio Set (If Equipped)
Audio Type A audio set (if equipped) P-201UN PUSH POWER-VOL AUDIO SEEK SCAN The audio set will operate only when the ignition switch is in the “ACC” or “ON” position. TUNE TRACK 500227...
Page 178: Radio Operation
Radio operation Power switch and volume control PUSH POWER-VOL 500228 The dial is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. The dial can also be used for tone and bal- ance adjustment.
Page 179 Audio Control mode (Range of levels) Turn counterclockwise Bass control (–6 to +6) For less bass sound Midrange control (–6 to +6) For less midrange sound Treble control (–6 to +6) For less treble sound Volume control (0 to 40) For less volume To change balance control mode 500009...
Page 180 Control mode (Range of levels) Turn counterclockwise Fader control (R9 to F9) To increase rear speaker volume and decrease front speaker vol- Balance control (L9 to R9) To increase left speaker volume and decrease right speaker vol- Volume control (0 to 40) For less volume FM/AM selection button 500009...
Page 181 Audio Tuning Manual tuning TUNE TRACK 500049 Press the “ ” side of the TUNE/TRACK button to increase the tuning frequency and press the “ ” side of the button to decrease it. Each time the button is pressed, the fre- quency interval can be changed between 10 kHz in the AM mode and 0.2 MHz in the FM mode.
Page 182: Compact Disc Player Operation
low frequencies). Automatic tuning may not function proper- ly if the station reception is weakened by distance from the station or proximity to tall buildings and hills. Selecting preset stations 500233 Presetting a station with a “preset button” allows you to select that station in a single operation.
Page 183 5-10 Audio NOTE After the last song finishes, the player will automatically return to track 1 (the first song on the disc). To stop playback of a CD When the “POWER-VOL” button is pressed during playback of a CD, the CD stops playing temporarily.
Page 184 Fast-reversing TUNE TRACK 500057 Press the “ ” side of the TUNE/TRACK button continuously to fast-reverse the disc. Release the button to stop fast-reversing. NOTE If you fast-reverse to the beginning of the first track on the disc, the fast-re- versing will stop and the player will start playing the first track on the disc.
Page 185 5-12 Audio Press the “RPT” button Press the “ ” or “ ” side of the SEEK/SCAN button Press the “ ” button Select the radio mode Turn off the power of the audio equipment. Turn the ignition switch to the “OFF” position.
Page 186: Type B Audio Set (If Equipped)
Type B audio set (if equipped) 6 CD CHANGER P-203UH PUSH POWER-VOL AUDIO SEEK SCAN The radio will operate only when the ignition switch is in the “ACC” or “ON” position. LOAD TUNE TRACK 500238 – CONTINUED – 5-13 Audio...
Page 187: Radio Operation
5-14 Audio Radio operation Power switch and volume/bass/tre- ble/fader/balance control Power switch and volume control PUSH POWER-VOL 500228 The dial is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial.
Page 188 Control mode (Range of levels) Turn counterclockwise Bass control (–6 to +6) For less bass sound Midrange control (–6 to +6) For less midrange sound Treble control (–6 to +6) For less treble sound Volume control (0 to 40) For less volume To change balance control modes 500009 Turn clockwise...
Page 189 5-16 Audio Control mode (Range of levels) Turn counterclockwise Fader control (R9 to F9) To increase rear speaker volume and decrease front speaker vol- Balance control (L9 to R9) To increase left speaker volume and decrease right speaker vol- Volume control (0 to 40) For less volume 500009 Turn clockwise...
Page 190 Tuning Manual tuning TUNE TRACK 500049 Push the “ ” side of the TUNE/TRACK button to increase the tuning frequency and press the “ ” side of the button to decrease it. Each time the button is pressed, the fre- quency interval can be changed between 10 KHz in the AM mode and 0.2 MHz in the FM mode.
Page 191: Built-In Cd Changer Operation
5-18 Audio frequency band (from high frequencies to low frequencies). Automatic tuning may not function proper- ly if the station reception is weakened by distance from the station or proximity to tall buildings and hills. Selecting preset stations 500233 Presetting a station with a preset button allows you to select that station in a single operation.
Page 192 peat Steps 1 and 2. The magazine will be loaded with discs in the ascending order of position number. If you do not insert any disc in 15 seconds after you have pressed the “LOAD” but- ton, the player will begin to play back the first track of the last disc you have insert- The disc indicator steadily lights up if a disc is already inserted in the correspond-...
Page 193 5-20 Audio and will steadily light. 3. When the loading of a disc is complete, the next disc number indicator will blink. Then repeat Step 2. 4. When the magazine is filled with discs by repeating Steps 2 and 3, the player will start playback of the discs, beginning with the one inserted first.
Page 194 Backward direction TUNE TRACK 500057 Briefly press the “ ” side of the TUNE/ TRACK button to skip to the beginning of the current track. Each time the button is pressed, the indicated track number will decrease. Fast-forwarding and fast-reversing Fast-forwarding TUNE TRACK...
Page 195 5-22 Audio Repeat playback To repeat the currently playing track 500235 To repeat a track, press the “RPT” button while the track is playing. The display will show “RPT”, and the track will be repeat- To cancel the track-repeat-play mode, press the “RPT”...
Page 196 and cancel the disc-repeat-play mode, press it again to reselect the disc-re- peat-play mode. The disc-repeat-play mode will be cancelled if you perform any of the fol- lowing steps: Press the “ ” or “ ” side of the SEEK/SCAN button Press the “RPT”...
Page 197 5-24 Audio the currently selected one. After all tracks on the disc have been scanned, normal playback mode is restored. To cancel a scan, press the “ ” or “ side of the button again. NOTE The scan mode will be cancelled if you perform any of the following steps: Press the “RPT”...
Page 198 sticking out, because vibration might make it fall out. If you press the “ ” button while the player is in all disc ejection mode, the mode will be cancelled following ejection of the disc that is currently be- ing ejected. If you press the “CD”...
Page 199: Type C Audio Set (If Equipped)
5-26 Audio Type C audio set (if equipped) PUSH POWER-VOL AUDIO FOLDER SEEK SCAN The audio set will operate only when the ignition switch is in the “ACC” or “ON” positions. 6 CD CHANGER P-203UE LOAD TEXT TUNE TRACK 500240...
Page 200: Radio Operation
Radio operation Power switch and volume control PUSH POWER-VOL 500228 The dial is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. The dial can also be used for tone and bal- ance adjustment.
Page 201 5-28 Audio Control mode (Range of levels) Turn counterclockwise Bass control (–6 to +6) For less bass sound Midrange control (–6 to +6) For less midrange sound Treble control (–6 to +6) For less treble sound Volume control (0 to 40) For less volume To change balance control modes 500009...
Page 202 Control mode (Range of levels) Turn counterclockwise Fader control (R9 to F9) To increase rear speaker volume and decrease front speaker vol- Balance control (L9 to R9) To increase left speaker volume and decrease right speaker vol- Volume control (0 to 40) For less volume FM/AM selection button 500009...
Page 203 5-30 Audio Tuning Manual tuning TUNE TRACK 500049 Press the “ ” side of the TUNE/TRACK button to increase the tuning frequency and press the tuning button marked “ to decrease it. Each time the button is pressed, the fre- quency interval can be changed between 10 kHz in the AM mode and 0.2 MHz in the FM mode.
Page 204: Built-In Cd Changer Operation
low frequencies). Automatic tuning may not function proper- ly if the station reception is weakened by distance from the station or proximity to tall buildings and hills. Selecting preset stations 500233 Presetting a station with a “preset button” allows you to select that station in a single operation.
Page 205 5-32 Audio 2. When the “LOAD” indicator flashes, in- sert the disc. Once you have inserted the disc, the “LOAD” indicator will go off. The disc will then be automatically drawn in, and the player will begin to play back the first track of the disc.
Page 206 button to start playback. Loading all the magazine (Full disc loading mode) LOAD 500239 1. If you continue to press the “LOAD” button for more than 1.5 seconds, the player will produce beep sound and will enter the full disc loading mode. 2.
Page 207 5-34 Audio the first track/file (track) in the folder. Backward direction TUNE TRACK 500057 Briefly press the “ ” side of the TUNE/ TRACK button to skip to the beginning of the current track/file (track). Each time the button is pressed, the indicated track/file (track) number will decrease.
Page 208 Repeating To repeat the currently playing track/file (track) 500241 To repeat a track/file (track), briefly press the “RPT” button while the track/file (track) is playing. The display will show “RPT”, and the track/file (track) will be repeated. To cancel the track/file (track) repeat-play mode, briefly press the “RPT”...
Page 209 5-36 Audio If you accidentally press the button and cancel the disc/folder repeat-play mode, press it again to reselect the disc/folder repeat-play mode. The disc/folder repeat-play mode will be cancelled if you perform any of the following steps: Press the “RPT” button Press the “...
Page 210 perform any of the following steps: Press the “RPT” button Press the “ ” or “ ” side of the TUNE/TRACK button Press the “ ” or “ ” side of the SEEK/SCAN button Press the “ ” button Press the disc select button Select the radio mode Turn off the power of the audio equipment.
Page 211 5-38 Audio How to unload CDs from the player Ejecting a CD from the player Of the discs loaded, you can select and re- move only one disc. 500233 1. Use the disc select button to select the disc to be ejected. 2.
Page 212: Audio Control Buttons (If Equipped)
the mode will be cancelled following ejection of the disc that is currently be- ing ejected. If you press the “CD” button while the player is in all disc ejection mode, the player will draw in the discs that have been ejected and play them. Audio control buttons (if equipped) These buttons are located on the spokes...
Page 213: Precautions To Observe When Handling A Compact Disc
5-40 Audio Volume control buttons 400218 Press the “+” button to increase the vol- ume. Press the “–” button to reduce the volume. A number indicating the volume will be shown on the audio display. MUTE button 400219 Press this button if you wish to immediate- ly cut the volume to zero.
Page 214 DualDisc You cannot use a DualDisc in the CD player. If you insert a DualDisc into the player, the disc may not come out again, possibly causing the player to malfunc- tion. In cold and/or rainy weather, dew can form inside the CD player, preventing nor- mal operation.
Page 215: Mp3 Audio
5-42 Audio 500034 MP3 audio What is MP3? MP3 (the name is an abbreviation of ‘MPEG Audio Layer 3’) is a compression format for digital audio. It was developed by the Motion Picture Experts Group. It permits audio data to be shrunk by a factor of approximately 10 with no loss of sound quality, meaning that the audio on 10 con- ventional CDs can be fitted onto a single...
Page 216: Supported File Systems
the writing software and CD recorder. Recording must be performed using a file system supported by the audio sys- tem. Otherwise, the audio system may not play the MP3 files and may not display folder titles and file titles. Supported file systems The audio system supports the following file systems: ISO 9660 Level 1/Level 2...
Page 218: Interior Equipment
Interior light ... Dome light ... Cargo area light (Station wagon) ... Map light ... Sun visors ... Sun visor extension plate ... Vanity mirror with light ... Storage compartment ... Glove box ... Center console box ... Center panel compartment (if equipped) ... Overhead console (if equipped) ...
Page 219: Interior Light
“Remote keyless entry system” sec- tion in chapter 2 for detailed information. The setting of the period for which the light Interior equipment stays on can be changed by a SUBARU dealer. Contact the nearest SUBARU dealer for details.
Page 220: Sun Visors
600496 Vehicle without moonroof To turn on the map light, push the switch. To turn it off, push the switch again. When leaving the vehicle, make sure the light is turned off to avoid battery dis- charge. Sun visors 400228 To block out glare, swing down the visors.
Page 221: Vanity Mirror With Light
Interior equipment 600408 Do not pull out the extension plate with the sun visor positioned over the windshield. The extension plate would obstruct your view of the rearview mirror. Vanity mirror with light 600498 To use the vanity mirror, swing down the sun visor and open the vanity mirror cov- The light beside the vanity mirror comes on when the ignition switch is either in the...
Page 222: Center Console Box
close it, push the lid firmly upward. To lock the glove box, insert the key and turn it clockwise. Center console box Center console box (front) 600500 If you remove the divider plate from the dual cupholders, you can use the center console box as a storage space.
Page 223: Center Panel Compartment (If Equipped)
Interior equipment Center console box (rear) 600201 Pull up the lock release knob at the bottom of the front edge of the lid. Center panel compartment (if equipped) When your vehicle is parked in the sun or a warm day, the inside of the center panel heats up.
Page 224: Cup Holder
Cup holder When not in use, always keep the cup holder stored while driving to reduce the risk of injury in the event of a sudden stop or an acci- dent. Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an acci-...
Page 225: Accessory Power Outlets
Interior equipment Accessory power outlets 600509 Outlet beside front ashtray 600209 Outlet in center console 600507 Outlet in cargo area Accessory power outlets are provided be- side the front ashtray, in the center con- sole and in the cargo area. Electrical pow- er (12V DC) from the battery is available at any of the outlets when the ignition switch is in either the “ACC”...
Page 226: Ashtray
When using appliances connect- ed to two or more outlets simulta- neously, the total power con- sumed by them must not exceed 120W. Overloading the accessory power outlet can cause a short circuit. Do not use double adapt- ers or more than one electrical ap- pliance.
Page 227: Coat Hook
6-10 Interior equipment 600512 To remove the ashtray for cleaning, hold the right and left sides of the ashtray and pull it out. Coat hook Rear passenger area 600516 Do not hang coat hangers or other hard or pointed objects on the coat hooks.
Page 228: Shopping Bag Hook
400249 The coat hook is attached to each rear passenger’s hand grip. Shopping bag hook Do not hang items on the shopping bag hook that weigh 11 lbs (5 kg) or more. For Sedan models 400253 A shopping bag hook is attached to each inner side wall of the trunk near the trunk lid opening.
Page 229: Floor Mat
6-12 Interior equipment Floor mat 600513 A retaining pin is located on the driver’s side of the vehicle next to the fuel filler door release. Fit the grommet in the car- pet onto the pin to prevent the carpet from moving.
Page 230: To Remove The Cover Housing
Do not place anything on the ex- tended cover. Putting excessive weight on the extended cover can break it and an object on the cover could tumble forward in the event of a sudden stop or collision. This could cause serious injury. To remove the cover housing 1.
Page 231: To Install The Cover Housing
6-14 Interior equipment 600110 2. To keep the lid open, hang the hook (provided on the back of the lid) on the rear edge of the roof. 3. Remove the left and right parts of the cargo floor lid. 400235 4.
Page 232: Stowage Boxes (Station Wagon)
til its top touches the rear gate panel. 400243 Fit the top of the rear gate board into the groove in the rear gate panel. Stowage boxes (Station wag- 600216 A stowage box is located on each side of the cargo area. You can access each one by pushing up and pulling the knob on the lid.
Page 233: Under-Floor Storage Compartment
6-16 Interior equipment ing recesses. Under-floor storage compart- ment The subfloor storage compartment is lo- cated under the floor of the trunk or cargo area and can be used to store small items. To open the lid, pull the tab or handle up. NOTE When storing a flat tire, put the sub- floor storage in the trunk or cargo area.
Page 234: Homelink® Wireless Control System (If Equipped)
HomeLink® Wireless Control System (if equipped) 600429 1) HomeLink® buttons 2) Indicator light 3) Hand-held transmitter* * Not part of your vehicle’s keyless entry system but of a HomeLink®-compatible device. The HomeLink® Wireless Control Sys- tem, located on the driver’s sun visor, is a handy way to operate, from inside of your vehicle, up to three remote-controlled in- door and outdoor devices, such as garage...
Page 235: Garage Door Opener Programming In The U.s.a
6-18 Interior equipment When programming the HomeLink® Wireless Control System to operate a garage door opener or an entrance gate, unplug the device’s motor from the outlet during programming to prevent motor burnout. NOTE After programming your HomeLink® Wireless Control System for the de- sired devices, retain the hand-held transmitters for further programming or device testing in the event of a prob-...
Page 236: Programming Rolling-Code-Protected Garage Door Openers In The U.s.a
your garage door opener may be protect- ed by a rolling code feature. In this case you need to perform the additional steps for “Programming rolling-code-protected garage door openers in the U.S.A.” de- scribed in the following. NOTE Rolling-code-protected garage door openers are manufactured after 1996.
Page 237: Programming For Entrance Gates And Garage Door Openers In Canada
6-20 Interior equipment trol System and your garage door opener should activate when the HomeLink® but- ton is pressed. Programming for entrance gates and garage door open- ers in Canada 1. Unplug the motor of the entrance gate or garage door opener from the outlet. 600430 2.
Page 238: Erasing Homelink® Button Memory
from the HomeLink® button surface. 3. Press and hold the hand-held transmit- ter button. The HomeLink® indicator light will flash, first slowly and then rapidly. 4. When the indicator light begins to flash rapidly, release both buttons. The programming for the previous device is now erased and the new device can be operated by pushing the HomeLink®...
Page 240: Starting And Operating
Fuel ... Fuel requirements ... Fuel filler lid and cap ... State emission testing (U.S. only) ... Preparing to drive ... Starting the engine ... Manual transmission vehicle ... Automatic transmission vehicle ... Stopping the engine ... Manual transmission ... Shifting speeds ...
Page 241: Fuel
The CHECK ENGINE warning light/Malfunction indicator lamp may also turn on. If this occurs, return to your autho- rized SUBARU dealer for diagnosis. If it is determined that the condition is caused by the type of fuel used, repairs may not be covered by your warranty.
Page 242 If this happens, return your authorized SUBARU Dealer for service. If it is deter- mined that the condition is caused by the type of fuel used, repairs may not be cov- ered by your warranty. Gasoline for cleaner air Do not let fuel spill on the exterior surfaces of the vehicle.
Page 243: Fuel Filler Lid And Cap
Starting and operating Fuel filler lid and cap Refueling 700342 1. To open the fuel filler lid, pull the lid re- lease lever. The lever is on the floor at the left of the driver’s seat. 700343 2. Open the fuel filler lid. 200255...
Page 244 Do not let fuel spill on the exterior surfaces of the vehicle. Fuels may cause paint damage, which is not covered under the SUBARU Limit- ed Warranty. – CONTINUED –...
Page 245: State Emission Testing (U.s. Only)
At state inspection time, remember to tell your inspection or service station in advance not to place your SUBARU AWD vehicle on a two-wheel dyna- mometer. Otherwise, serious transmis- sion damage will result.
Page 246: Preparing To Drive
Owners of rejected or failing vehicles should contact their SUBARU Dealer for service. Starting and operating Preparing to drive You should perform the following checks and adjustments every day before you start driving.
Page 247: Starting The Engine
“START” position without depressing the accelerator pedal. 4) If the engine still refuses to start, con- tact your nearest SUBARU dealer for assistance. 6. Confirm that all warning and indicator lights have gone off after the engine has started.
Page 248: Stopping The Engine
“START” position without depressing the accelerator pedal. 4) If the engine still refuses to start, con- tact your nearest SUBARU dealer for assistance. 6. Confirm that all warning and indicator lights have gone out after the engine has started.
Page 249: Shifting Speeds
7-10 Starting and operating 700101 The shift pattern is shown on the shift le- ver knob. When shifting from 5th gear to reverse gear, first return the shift lever to the neutral position then shift into reverse gear. To change gears, fully depress the clutch pedal, move the shift lever, and gradually let up on the clutch pedal.
Page 250: Driving Tips
Never exceed posted speed limits. Driving tips Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill on an up- grade. Either of those actions may cause clutch damage.
Page 251: Selector Lever
7-12 Starting and operating Avoid shifting from one of the for- ward driving positions into the “R” position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmission. When parking the vehicle, first se- curely apply the parking brake and then place the selector lever in the “P”...
Page 252: Selector Lever Reverse Inhibiting Function
NOTE If the selector lever is in the “N” posi- tion when you stop the engine for park- ing, you may not subsequently be able to move it to the “R” and “P” positions. If this happens, turn the ignition switch to the “ON”...
Page 253: Selection Of Manual Mode
“P” position. If the selector lever reverse inhibiting function fails, have the vehicle inspected by the nearest SUBARU dealer. Selection of manual mode 700109 With the vehicle either moving or station- ary, move the selector lever from the “D”...
Page 254: Maximum Speeds
Gearshifts can be performed using the se- lector lever. 700111 Using the selector lever Shift to the next-higher gear by briefly pushing the selector lever toward the “+” end of the manual gate. Shift to the next-lower gear by briefly pull- ing the selector lever toward the “–”...
Page 255: Driving Tips
7-16 Starting and operating mph (km/h) Position 2.5-liter non-turbo models 34 (55) 64 (103) 99 (160) Never exceed posted speed limits. Driving tips On a road surface where there is a risk of wheelspin (for example, a snow- or gravel-covered road), you can pull away from a standstill (safely and easily) by first selecting the 2nd gear of the manual mode.
Page 256: Automatic Transmission - 5-Speed
“P” to the “N” position. 6. Remove the screwdriver from the hole. Depress the brake pedal and start the en- gine. Take your vehicle to the nearest SUBARU dealer immediately to have the system re- paired. 7-17 Starting and operating Automatic transmission –...
Page 257: Selector Lever
7-18 Starting and operating Avoid shifting from one of the for- ward driving positions into the “R” position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmission. When parking the vehicle, first se- curely apply the parking brake and then place the selector lever in the “P”...
Page 258 transmission is neutral; the vehicle will roll freely, even on the slightest incline unless the parking brake or foot brake is on. Avoid coasting with the transmission neu- tral. During coasting, there is no engine brak- ing effect. NOTE (3.0-liter models only) To protect the engine while the “N”...
Page 259: Selector Lever Reverse Inhibiting Function
“P” position. If the selector lever reverse inhibiting function fails, have the vehicle inspected by the nearest SUBARU dealer. Selection of manual mode 700109 With the vehicle either moving or station- ary, move the selector lever from the “D”...
Page 260 700308 1) Upshift indicator 2) Downshift indicator 3) Gear position indicator When the manual mode is selected, the gear position indicator and upshift indica- tor and/or downshift indicator in the ta- chometer come on. The gear position indi- cator shows the currently selected gear in the 1st-to-5th-gear range.
Page 261: Maximum Speeds
7-22 Starting and operating transmission will automatically switch back from manual mode to normal mode. NOTE Please read the following points care- fully and bear them in mind when using the manual mode. When the temperature of the auto- matic transmission fluid is higher than normal, warning beeps are emitted and the shift position indicator shows “–”.
Page 262: Driving Tips
mph (km/h) Position 2.5-liter turbo 3.0-liter models models 35 (57) 27 (43) 59 (95) 61 (98) 94 (151) 96 (154) Never exceed posted speed limits. Driving tips On a road surface where there is a risk of wheelspin (for example, a snow- or gravel-covered road), you can pull away from a standstill safely and easily by first selecting the 2nd gear of the manual...
Page 263: Rear Viscous Limited Slip Differential (Lsd) (If Equipped)
“N” position. 6. Remove the screwdriver from the hole. Depress the brake pedal and start the en- gine. Take your vehicle to the nearest SUBARU dealer immediately to have the system re- paired. Rear viscous limited slip dif- ferential (LSD) (if equipped)
Page 264: Power Steering
Power steering Do not hold the steering wheel at the fully locked position left or right for more than five seconds. This may damage the power steering pump. The power steering system operates only when the engine is running. If you lose power steering assist because the engine stops or the system fails to function, you can steer but it will take much more effort.
Page 265: Disc Brake Pad Wear Warning Indicators
If a squeaking or scraping noise is heard from the disc brakes while braking, imme- diately have your vehicle inspected by the nearest SUBARU dealer. ABS (Anti-lock Brake Sys- tem) Always use the utmost care in driv- ing –...
Page 266: Abs Warning Light
The warning light comes on dur- ing driving. If these occur, have the ABS system repaired at the first available oppor- tunity by your SUBARU dealer. NOTE If the warning light behavior is as de- scribed in the following, the ABS sys- tem may be considered normal.
Page 267: Electronic Brake Force Distribution (Ebd) System
5. If the brake fluid level is not below the “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system in- spected. 6. If the brake fluid level is below the “MIN”...
Page 268: Vehicle Dynamics Control System (If Equipped)
This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately. If at all in doubt about whether the brakes are operating properly, do not drive the vehicle.
Page 269 7-30 Starting and operating – Keep the tire pressure at the proper level as shown on the vehicle placard attached to the driver’s side door pillar. In the event of wheelspin and/or skidding on a slippery road surface and/or during cornering and/or an evasive maneuver, the Vehicle Dynamics Control system ad- justs the engine’s output and the wheels’...
Page 270: Vehicle Dynamics Control System Monitor
The following two situations could indicate a malfunction of the Vehicle Dynamics Control system; if either should occur, have an authorized SUBARU dealer carry out an inspection of that system at the first available opportunity. The indicator light does not turn on when the ignition switch is turned to the ON position.
Page 271: Vehicle Dynamics Control Off Switch
SUBARU dealer carry out an inspection of those systems at the first available oppor- tunity. NOTE...
Page 272: Tire Pressure Monitoring System (Tpms) (If Equipped)
The Vehicle Dynamics Control system will be deactivated and the vehicle will behave like a model not equipped with the Vehicle Dynamics Control system. When the switch is pressed again to reactivate the Vehicle Dynamics Control system, the in- dicator light goes off. With the Vehicle Dynamics Control sys- tem deactivated, traction and stability en- hancement offered by Vehicle Dynamics...
Page 273 This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU deal- er as soon as possible for tire and sensor replacement and/or system resetting.
Page 274: Parking Your Vehicle
Do not place metal film or any metal parts under the driver’s seat. This may cause poor reception of the sig- nals from the tire pressure sensors, and the tire pressure monitoring system will not function properly. NOTE This device complies with Part 15 of the FCC Rules and with RSS-210 of In- dustry Canada.
Page 275: Cruise Control
7-36 Starting and operating cle, be sure that the warning light has gone out before the vehicle is driven. Re- fer to the “Warning and indicator lights” section (chapter 3). When parking your vehicle, always set the parking brake firmly and put the shift lever in the “1”...
Page 276: To Set Cruise Control
To set cruise control 300332 1. Push the main switch button. 300210 The “ ” indicator light on the com- bination meter will come on. 2. Depress the accelerator pedal until the vehicle reaches the desired speed. 3. Push the control lever downward in the “SET/COAST”...
Page 277: To Turn Off The Cruise Control
7-38 Starting and operating Depress the clutch pedal (manual trans- mission vehicles only). Shift the selector lever into the “N” posi- tion (automatic transmission vehicles only). Shift the shift lever into neutral position (manual transmission vehicles only). The “ ” indicator light in the combina- tion meter goes off when the cruise control is cancelled.
Page 278: Cruise Control Indicator Light
To decrease the speed (by control lever) 300333 Push the control lever downward in the “SET/COAST” direction and hold it until the vehicle reaches the desired speed. Then, release the control lever. The vehi- cle speed at that moment will be memo- rized and treated as the new set speed.
Page 280: Driving Tips
New vehicle break-in driving – the first 1,000 miles (1,600 km) ... Fuel economy hints ... Engine exhaust gas (Carbon monoxide) ... Catalytic converter ... Periodic inspections ... Driving in foreign countries ... Driving tips for AWD vehicles ... Off road driving ... Winter driving ...
Page 281: New Vehicle Break-In Driving - The First
Driving tips New vehicle break-in driving – the first 1,000 miles (1,600 The performance and long life of your ve- hicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): Do not race the engine.
Page 282: Catalytic Converter
If at any time you suspect that ex- haust fumes are entering the vehi- cle, have the problem checked and corrected as soon as possi- ble. If you must drive under these conditions, drive only with all win- dows fully open. Keep the trunk lid (Sedan) or rear gate (Station wagon) closed while driving to prevent exhaust gas...
Page 283: Periodic Inspections
(misfiring, back- firing or incomplete combustion), have your vehicle checked and repaired by an authorized SUBARU dealer. Do not apply undercoating or rust pre- vention treatment to the heat shield of cat- alytic converter and the exhaust system.
Page 284: Driving Tips For Awd Vehicles
By shifting power between the front and rear wheels, SUBARU AWD can also provide added traction during acceleration, and added engine braking force during decel- eration.
Page 285: Off Road Driving
If you do take your SUBARU off road, you should review the common sense precau- tions in the next section (applicable to the OUTBACK) for general guidance.
Page 286: Winter Driving
“Warranty and Maintenance Booklet”. Remember that damage done to your SUBARU while operating it off-road and not using common sense precautions such as those listed above is not eligible for warranty coverage.
Page 287 SUBARU Windshield Washer Fluid con- tains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing temper- ature varies according to how much it is di- luted, as indicated in the following table.
Page 288: Driving On Snowy And Icy Roads
If your SUBARU is not going to be used for an extended period, it is best to have the fuel tank filled to capacity.
Page 289: Corrosion Protection
8-10 Driving tips wiper blades (winter blades) during the seasons you could have snow and sub- zero temperatures. Blades of this type give superior wiping performance in snowy conditions. Be sure to use blades that are suitable for your vehicle. During high-speed driving, non- freezing type wiper blades may not perform as well as standard wiper...
Page 290: Tire Chains
OUTBACK models only When replacing original tires with winter (snow) tires, make sure you use only the same size and con- struction as recommended. Using other sizes or construction may affect speedometer/odometer cal- ibration and clearance between the body and tires. It also may be dangerous and lead to loss of ve- hicle control.
Page 291: Rocking The Vehicle
8-12 Driving tips require the use of tire chains, in which case put the chains on the front wheels only. Use only SAE class S type chains that are of the correct size for your tires so as not to damage the vehicle body or sus- pension.
Page 292: Vehicle Capacity Weight
When you carry something inside the vehicle, secure it whenever you can to prevent it from being thrown around inside the vehicle during sudden stops, sharp turns or in an accident. Do not pile heavy loads on the roof. These loads raise the vehi- cle’s center of gravity and make it more prone to tip over.
Page 293: Gvwr And Gawr (Gross Vehicle Weight Rating And Gross Axle Weight Rating)
8-14 Driving tips GVWR and GAWR (Gross Ve- hicle Weight Rating and Gross Axle Weight Rating) 800237 Certification label The certification label attached to the driv- er’s side door shows GVWR (Gross Vehi- cle Weight Rating) and GAWR (Gross Axle Weight Rating). The GVW (Gross Vehicle Weight) must never exceed the GVWR.
Page 294 When using the roof crossbar kit, make sure that the total weight of the crossbars, carrying attach- ment and cargo does not exceed the maximum load limit. Overload- ing may cause damage to the ve- hicle and create a safety hazard. The roof rail is not designed to carry cargo by itself.
Page 295 8-16 Driving tips 2. Carefully raise the crossbar from roof rails. To install the front crossbar Front crossbar: Front crossbar has 100 LBS Load Label on left-hand side. 800241 1) T-25 torx® head screw 1. Make sure that the T-25 torx® head screw on the back of each crossbar end support is tightened correctly.
Page 296 800244 1) Lower clamp 2) T-30 torx® head screw 5. Tighten the lower clamps onto the crossbar. Using a torque wrench, loosely tighten the T-30 torx® head screws. NOTE It may be necessary to squeeze the lower clamp and the end support to- gether to compress the pads and gain a better alignment of the pieces while trying to start the screw.
Page 297: Trailer Hitch (If Equipped)
8-18 Driving tips NOTE Before each use of the roof crossbar, make sure the four T-30 crossbar clamp screws have been checked, and retightened if necessary to 35 lbf·in (4.0 N·m, 0.41 kgf·m), as outlined in Step #5 above. Trailer hitch (if equipped) Never exceed maximum...
Page 298: Connecting A Trailer
Connecting a trailer 1. Remove the receiver cover from the hitch receiver tube. Then insert the ball mount into the hitch receiver tube. 800206 2. Insert the hitch pin into the hole on the hitch receiver tube so that the pin passes through the ball mount.
Page 299: When You Do Not Tow A Trailer
Seek the advice of your SUBARU dealer to assist you in pur- chasing a hitch and other necessary tow- ing equipment appropriate for your vehi- cle.
Page 300: Maximum Load Limits
required due to the additional load. (Refer to “Maintenance schedule under severe driving conditions” in the “Warranty and Maintenance Booklet”.) Under no circumstances should a trailer be towed with a new vehicle or a vehicle with any new powertrain component (en- gine, transmission, differential, wheel bearings, etc.) for the first 1,000 miles (1,600 km) of driving.
Page 301 8-22 Driving tips 3,0-liter models Conditions When towing a trailer without brakes. When towing a trailer with brakes. When towing a trailer on a long uphill grade con- tinuously for over 5 miles (8 km) with an outside temperature of 104°F (40°C) or above. All models other than 3.0-liter models Model MT models...
Page 302 cle. 800237 Certification label Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR) 800249 Gross Axle Weight The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehi- cle.
Page 303: Trailer Hitches
8-24 Driving tips 800250 1) Jack 2) Bathroom scale The tongue load can be weighed with a bathroom scale as shown in the following illustration. When weighing the tongue load, be sure to position the towing cou- pler at the height at which it would be dur- ing actual towing, using a jack as shown.
Page 304 OUTBACK wagon The use of a genuine SUBARU trailer hitch recommended. genuine SUBARU hitch is available from your SUBARU dealer. If use of a non-genuine hitch is unavoid- able, be sure the hitch is suited to your ve- hicle and trailer. Consult with a profes-...
Page 305 To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the turn signals, the brake lights and parking lights each time you hitch up.
Page 306 If the ABS warning light illuminates while the vehicle is in motion, stop towing the trailer and have repairs performed im- mediately by the nearest SUBARU dealer. Driving on grades Before going down a steep hill, slow down and shift into lower gear (if neces-...
Page 307 8-28 Driving tips sary, use 1st gear) in order to utilize the engine braking effect and prevent over- heating of your vehicle’s brakes. Do not make sudden downshifts. When driving uphill in hot weather, the air conditioner may turn off automatically to protect the engine from overheating.
Page 308: In Case Of Emergency
In case of emergency If you park your vehicle in an emergency ... Temporary spare tire ... Flat tires ... Changing a flat tire ... Tire pressure monitoring system (TPMS) (if equipped) ... Jump starting ... 9-10 How to jump start ... Engine overheating ...
Page 309: Temporary Spare Tire
This indicates the tire pres- sure monitoring system (TPMS) is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/or system resetting.
Page 310 Never use any temporary spare tire other than the original. Using other sizes may result in severe mechani- cal damage to the drive train of your vehicle. The temporary spare tire is smaller and lighter than a conventional tire and is de- signed for emergency use only.
Page 311: Flat Tires
In case of emergency Flat tires If you have a flat tire while driving, never brake suddenly; keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place. Changing a flat tire Do not jack up the vehicle on an incline or a loose road surface.
Page 312 900243 Station wagon 1) Jack handle 2) Jack and tool bucket 3) Spare tire 5. Take out the spare tire, jack, and jack handle. The spare tire and jack are stored under the floor of the trunk or cargo area. To remove the spare tire and jack, pro- ceed as follows: Sedan:...
Page 313 In case of emergency 600113 6. Turn the attaching bolt counterclock- wise, then take the spare tire out. Station wagon: 600110 1. Open the lid and hang the hook provid- ed on the under side of the lid on the rear edge of the roof to keep the lid open.
Page 314 600113 6. Turn the attaching bolt counterclock- wise, then take spare tire out. If the spare tire provided in your vehicle is a temporary spare tire, carefully read the section “Temporary spare tire” in this chapter and strictly follow the instructions. NOTE Make sure the jack is well lubricated before using it.
Page 315 In case of emergency 10.Remove the wheel nuts and the flat tire. 900009 600162 11.Before putting the spare tire on, clean the mounting surface of the wheel and hub with a cloth. 12.Put on the spare tire. Replace the wheel nuts. Tighten them by hand. Do not use oil or grease on the wheel studs or nuts when the spare tire is installed.
Page 316: Tire Pressure Monitoring System (Tpms) (If Equipped)
Do not inject any tire liquid or aero- sol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. If the light flashes, promptly contact a SUBARU dealer to have the sys- tem inspected.
Page 317: Jump Starting
9-10 In case of emergency Jump starting Battery fluid is SULFURIC ACID. Do not let it come in contact with the eyes, skin, clothing or the ve- hicle. If battery fluid gets on you, thor- oughly flush the exposed area with water immediately.
Page 318 9-11 In case of emergency 1) Connect one jumper cable to the pos- itive (+) terminal on the discharged bat- tery. 2) Connect the other end of the jumper cable to the positive (+) terminal of the booster battery. 3) Connect one end of the other cable to the negative (–) terminal of the booster battery.
Page 319: Engine Overheating
9-12 In case of emergency 5. Start the engine of the vehicle with the booster battery and run it at moderate speed. Then start the engine of the vehi- cle that has the discharged battery. 6. When finished, carefully disconnect the cables in exactly the reverse order.
Page 320: Towing
900030 If towing is necessary, it is best done by your SUBARU dealer or a commercial towing service. Observe the following pro- cedures for safety. Towing and tie-down hooks The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle...
Page 321 9-14 In case of emergency 4. Screw the towing hook into the thread hole until the threads can no longer be seen. 900248 5. Tighten the towing hook securely using a wheel nut wrench. After towing, remove the towing hook from the vehicle and stow it in the tool bag.
Page 322 900252 6. Tighten the towing hook securely using a wheel nut wrench. After towing, remove the towing hook from the vehicle and stow it in the tool bag. Fit the fog light cover and towing hook cover on the bumper. Do not use the towing hook ex- cept when towing your vehicle.
Page 323: Using A Flat-Bed Truck
9-16 In case of emergency each of the jack-up reinforcements. Use the rear tie-down hooks only for downward anchoring. If they are used to anchor the vehicle in any other direction, cables may slip off the hooks, possibly causing a dan- gerous situation.
Page 324: Rear Gate (Station Wagon) - If The Rear Gate Cannot Be Unlocked
3. The ignition switch should be in the “ACC” position while the vehicle is being towed. 4. Take up slack in the towline slowly to prevent damage to the vehicle. Rear gate (Station wagon) – if the rear gate cannot be un- locked In the event that you cannot unlock the rear gate by operating the power door...
Page 325: Maintenance Tools
9-18 In case of emergency Maintenance tools Jack A jack and other maintenance tools are stored in the tool bucket in the center of the spare tire located in the trunk or in the cargo area. 900244 Sedan: To take out the jack and mainte- nance tools, open the floor cover and re- move the bucket from the center of the spare tire.
Page 326: Other Maintenance Tools
For how to use the jack, refer to “Flat tires”. Other maintenance tools In addition to a jack and a jack handle, the tool bucket on your vehicle contains the following maintenance tools. 900259 Screwdriver Towing hook Wheel nut wrench 9-19 In case of emergency...
Page 328 Appearance care Exterior care ... 10-2 Washing ... Waxing and polishing ... Cleaning aluminum wheels ... Corrosion protection ... 10-4 Most common causes of corrosion ... To help prevent corrosion ... Cleaning the interior ... 10-5 Seat fabric ... Leather seat materials ... Synthetic leather upholstery ...
Page 329: Exterior Care
10-2 Appearance care Exterior care Washing When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes.
Page 330: Appearance Care
When in doubt, it is always best to contact your SUBARU dealer or an auto paint specialist. NOTE Be careful not to block the windshield washer nozzles with wax when waxing the vehicle.
Page 331: Corrosion Protection
Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need assistance. Repair chips and scratches in the paint as soon as you find them.
Page 332: Cleaning The Interior
If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage.
Page 334: Maintenance And Service
Maintenance schedule ... Maintenance precautions ... Before checking or servicing in the engine compartment ... When you do checking or servicing in the engine compartment while the engine is running ... Engine hood ... Engine compartment overview ... 2.5-liter non-turbo models ... 2.5-liter turbo models ...
Page 335 Maintenance and service Replacement of brake pad and lining ... 11-31 Breaking-in of new brake pads and linings ... 11-32 Parking brake stroke ... 11-32 Tires and wheels ... 11-33 Types of tires ... 11-33 Tire pressure monitoring system (TPMS) (if equipped) ...
Page 336: Maintenance Schedule
Maintenance precautions When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer. If you perform maintenance and service by yourself, you should familiarize your- self with the information provided in this section on general maintenance and ser- vice for your SUBARU.
Page 337: Before Checking Or Servicing In The Engine Compartment
NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt pre- tensioner needs service, consult your nearest SUBARU dealer. Before checking or servicing in the engine compartment Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.
Page 338 200258 3. Release the secondary hood release located under the front grille by moving the lever toward the left. 200259 4. Lift up the hood, release the hood prop from its retainer and put the end of the hood prop into the slot in the hood. To close the hood: 1.
Page 339: Engine Compartment Overview
11-6 Maintenance and service Engine compartment overview 2.5-liter non-turbo models B00414 Power steering fluid reservoir (page 11-27) Manual transmission oil level gauge (MT) (page 11-20) or Differential gear oil level gauge (AT) (page 11-23) Clutch fluid reservoir (page 11-29) Automatic transmission fluid level gauge (page 11-22) Brake fluid reservoir (page 11-28) Fuse box (page 11-45)
Page 340: 2.5-Liter Turbo Models
2.5-liter turbo models B00416 11-7 Maintenance and service Power steering fluid reservoir (page 11-27) Manual transmission oil level gauge (MT) (page 11-20) or Differential gear oil level gauge (AT) (page 11-23) Clutch fluid reservoir (page 11-29) Brake fluid reservoir (page 11-28) Automatic transmission fluid level gauge (page 11-22) Fuse box (page 11-45)
Page 341: 3.0-Liter Models
11-8 Maintenance and service 3.0-liter models B00502 Power steering fluid reservoir (page 11-27) Differential gear oil level gauge (AT) (page 11-23) Automatic transmission fluid level gauge (page 11-22) Brake fluid reservoir (page 11-28) Fuse box (page 11-45) Battery (page 11-44) Windshield washer tank (page 11-39) Engine oil filler cap (page 11-9) Engine coolant reservoir (page 11-...
Page 342: Engine Oil
Engine oil Checking the oil level Check the engine oil level at each fuel stop. 1. Park the vehicle on a level surface and stop the engine. B00104 2. Pull out the dipstick, wipe it clean, and insert it again. 3.
Page 343: Changing The Oil And Oil Filter
11-10 Maintenance and service If you check the oil level just after stopping the engine, wait a few minutes for the oil to drain back into the oil pan before checking the level. To prevent overfilling the engine oil, do not add any additional oil above the upper lev- el when the engine is cold.
Page 344 B00306 3.0-liter models 6. Open the access cover by removing the clips and turning the access cover counterclockwise. The oil filter will be ex- posed. B00421 2.5-liter models B00307 3.0-liter models 7. Remove the oil filter with an oil filter wrench.
Page 345: Recommended Grade And Viscosity
The following ta- ble lists the recommended viscosities and applicable temperatures. When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those recommended by SUBARU.
Page 346: Recommended Grade And Viscosity Under Severe Driving Conditions
–33°F (–36°C). For adding, use genuine SUBARU coolant or an equivalent: a mixture of 50% soft water and 50% ethylene-glycol ba- sis coolant. Use of improper cool- ants may result in corrosion in the cooling system.
Page 347: Hose And Connections
Check the fuse and replace it if necessary. If the fuse is not blown, have the cooling system checked by your SUBARU dealer. If frequent addition of coolant is neces- sary, there may be a leak in the engine cooling system.
Page 348 Changing the coolant Always add genuine Subaru cooling sys- tem conditioner whenever the coolant is replaced. Change the engine coolant and add gen- uine Subaru cooling system conditioner using the following procedures according to the maintenance schedule in the “War- ranty and Maintenance Booklet”.
Page 349 Maintenance and service 5. Slowly pour the coolant and fill up to just below the filler neck, allowing enough room to add genuine Subaru cooling sys- tem conditioner in the radiator. Add genu- ine Subaru cooling system conditioner un- til the coolant level reaches the filler neck.
Page 350: Air Cleaner Element
Replace the air cleaner element according to the maintenance schedule in the “War- ranty and Maintenance Booklet”. Under extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts. Non-turbo models B00426 1) Connector 2) Duct 3) Clamp 1.
Page 351 11-18 Maintenance and service 7. To install the air cleaner case cover, in- sert the three projections on the air clean- er case cover into the slits on the air clean- er case and then snap the two clamps on the air cleaner case cover.
Page 352: Spark Plugs
It may be difficult to replace the spark plugs. It is recommended that you have spark plugs replaced your SUBARU dealer. The spark plugs should be replaced ac- cording to the maintenance schedule in the “Warranty and Maintenance Booklet”. 11-19 Maintenance and service Recommended spark plugs 2.5-liter non-turbo models:...
Page 353: Drive Belts
However, replacement of the belt should be done according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Consult your SUBARU dealer for replacement. If a belt is loose, cracked, or worn, contact your SUBARU dealer. Manual transmission oil...
Page 354: Recommended Grade And Viscosity
B00196 Turbo models 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the dipstick, wipe it clean, and insert it again. B00368 1) Upper level 2) Lower level 3. Pull out the dipstick again and check the oil level on it.
Page 355: Automatic Transmission Fluid
11-22 Maintenance and service Automatic transmission fluid Checking the fluid level The automatic transmission fluid expands largely as its temperature rises; the fluid level differs according to fluid tempera- ture. Therefore, there are two different scales for checking the level of hot fluid and cold fluid on the dipstick.
Page 356: Recommended Fluid
Recommended fluid Use one of the following types of automat- ic transmission fluid. Genuine Subaru Automatic Transmis- sion Fluid Type-HP IDEMITSU ATF HP Castrol Transmax J Pennzoil ATF-J* * Available only in the USA (except...
Page 357: Recommended Grade And Viscosity
11-24 Maintenance and service Recommended grade and viscosity Each oil manufacturer has its own base oils and additives. Never use different brands together. Oil grade: API classification GL-5 -30 -20 -10 75W/90 B00032 SAE viscosity No. and applicable tem- perature Rear differential gear oil Checking the gear oil level Your vehicle may be equipped with a rear...
Page 358 B00433 2.5-liter turbo and 3.0-liter models (AT) 1) Filler plug 2) Drain plug B00320 2.5-liter turbo and 3.0-liter models (AT) 1) Filler hole 2) Drain hole 3) Oil level 11-25 Maintenance and service B00373 Others 1) Filler plug 2) Drain plug –...
Page 359: Recommended Grade And Viscosity
If the vehicle requires frequent re- filling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. Recommended grade and viscosity Each oil manufacturer has its own base oils and additives.
Page 360: Power Steering Fluid
“MIN” and “MAX” line. 11-27 Maintenance and service If the fluid level is extreme low, it may indi- cate possible leakage. Consult your SUBARU dealer for inspection. Recommended fluid “Dexron III” Type Automatic Transmis- sion Fluid...
Page 361: Brake Fluid
If the vehicle requires frequent re- filling, there may be a leak. If you suspect a problem, have the vehi- cle checked at your SUBARU dealer. Never use different brands of brake fluid together. Also, avoid mixing DOT 3 and DOT 4 brake flu- ids even if they are of the same brand.
Page 362: Clutch Fluid (Mt Vehicles)
If the vehicle requires frequent re- filling, there may be a leak. If you suspect a problem, have the vehi- cle checked at your SUBARU dealer. Never use different brands of clutch fluid together. When clutch fluid is added, be careful not to allow any dirt into the tank.
Page 363: Specifications
2 lbs (10 N, 1 kg). If the free play is not within proper specifi- cation, contact your SUBARU dealer. Checking the brake pedal re- serve distance B00324 1) More than 2.56 in (65 mm)
Page 364: Clutch Pedal (Manual Transmission Vehicles)
Lightly press the clutch pedal down with your finger until you feel resistance, and check the free play. If the free play is not within proper specifi- cation, contact your SUBARU dealer. 11-31 Maintenance and service Replacement of brake pad...
Page 365: Breaking-In Of New Brake Pads And Linings
11-32 Maintenance and service you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible. Breaking-in of new brake pads and linings When replacing the brake pad or lining, use only genuine SUBARU parts. After re-...
Page 366: Tires And Wheels
Tires and wheels Types of tires You should be familiar with type of tires present on your vehicle. All season tires The factory-installed tires on your new ve- hicle are all season tires. All season tires are designed to provide an adequate measure of traction, handling and braking performance in year-round driving including snowy and icy road con-...
Page 367: Tire Inspection
In this event, go to a SUBARU dealer to have the system inspected as soon as possible. While the vehicle is driven, friction be- tween tires and the road surface causes the tires to warm up.
Page 368: Tire Pressures And Wear
Drive slowly nearest authorized SUBARU dealer and have the vehicle inspected. Tire pressures and wear Maintaining the correct tire pressures helps to maximize the tires’ service lives and is essential for good running perfor- mance.
Page 369 11-36 Maintenance and service Correct tire pressure (tread worn evenly) B00050 Roadholding is good, and steering is re- sponsive. Rolling resistance is low, so fuel consumption is also lower. Abnormally low tire pressure (tread worn at shoulders) B00051 Rolling resistance is high, so fuel con- sumption is also higher.
Page 370: Wheel Balance
Loss of correct wheel alignment* caus- es the tires to wear on one side and re- duces the vehicle’s running stability. Contact your SUBARU dealer if you no- tice abnormal tire wear. *: The suspension system is designed to hold...
Page 371: Tire Replacement
You are advised to re- place the tires with new ones that are identical to those fitted as standard equip- ment. For safe vehicle operation, SUBARU rec- ommends replacing all four tires at the same time. All four tires must be the same in...
Page 372: Aluminum Wheels
When wheel nuts, balance weights, or the center cap is replaced, be sure to re- place them with genuine SUBARU parts designed for aluminum wheels. 11-39 Maintenance and service...
Page 373 In areas where water freezes in winter, use an anti-freeze type windshield washer fluid. SUBARU Windshield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing temper- ature varies according to how much it is di- luted, as indicated in the following table.
Page 374: Replacement Of Wiper Blades
Replacement of wiper blades Grease, wax, insects, or other materials on the windshield or the wiper blade re- sults in jerky wiper operation and streak- ing on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield (or rear window) and the wiper blades us- ing a sponge or soft cloth with a neutral...
Page 375: Windshield Wiper Blade Rubber
11-42 Maintenance and service Windshield wiper blade rub- B00330 1) Metal support 1. Grasp the locked end of the blade rub- ber assembly and pull it firmly until the stoppers on the rubber are free of the met- al support. B00504 1) Metal spines 2.
Page 376: Rear Window Wiper Blade Rubber
700063 2. Turn the wiper blade assembly coun- terclockwise. 700064 3. Pull the wiper blade assembly toward you to remove it from the wiper arm. Rear window wiper blade rub- 700017 1. Pull out the end of the blade rubber as- sembly to unlock it from the plastic sup- port.
Page 377: Battery
11-44 Maintenance and service B00066 4. Align the claws of the plastic support with the grooves in the blade rubber as- sembly, then slide the blade rubber as- sembly into place. B00067 Securely retain both ends of the rubber with the stoppers on the plastic support ends.
Page 378: Fuses
To lessen the risk of sparks, re- move rings, metal watchbands, and other metal jewelry. Never al- low metal tools to contact the pos- itive battery terminal and anything connected to it WHILE you are at the same time in contact with any other metallic portion of the vehi- cle because a short circuit will re- sult.
Page 379 11-46 Maintenance and service B00131 Open the lid that is located above the hood release knob and pull it toward you to remove it. 600120 The other one is housed in the engine compartment. B00198 The spare fuses are stored in the main fuse box cover in the engine compart- ment.
Page 380: Main Fuse
6. If the same fuse blows again, this indi- cates that its system has a problem. Con- tact your SUBARU dealer for repairs. Main fuse 600120 Main fuse box...
Page 381: Replacing Bulbs
11-48 Maintenance and service Replacing bulbs B00435...
Page 382: Headlight
NOTE If headlight aiming is required, con- sult your SUBARU dealer for proper adjustment of the headlight aim. It may be difficult to replace the bulbs. Have your SUBARU dealer re- place the bulbs if necessary.
Page 383: Parking Light
5. To install the bulb to the headlight as- sembly, turn it clockwise until it clicks. Parking light It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary. Front turn signal light It may be difficult to replace the bulbs.
Page 384: Rear Combination Lights
Rear combination lights Sedan B00436 1. Push the knobs of the cover to open the cover. B00437 1) Rear turn signal light 2) Backup light 3) Brake/tail and rear side marker light 2. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise.
Page 385: Backup Light (Station Wagon)
11-52 Maintenance and service gap A between the side cover and rear combination lamp and use it as a lever to undo the clip. Undo clips C and D in the same way, then remove the side cover. B00136 3. Remove the upper and lower screws. Then, slide the rear combination lamp as- sembly to the rear and remove it from the vehicle.
Page 386: License Plate Light
Install the light cover on the rear gate. License plate light Sedan It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary. Station wagon 700076 1. Remove the mounting screws using a Phillips screwdriver.
Page 387: Map Light
11-54 Maintenance and service 700084 2. Turn the bulb until the flat surfaces at its ends are aligned vertically. Pull the bulb straight downward to remove it. In- stall a new bulb. 3. Reinstall the lens. Map light B00440 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver.
Page 388: Cargo Area Light (Station Wagon)
700082 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the lens. Cargo area light (Station wag- 700078 1. Remove the cargo area light assembly by prying the edge of the light with a flat- head screwdriver.
Page 389: High Mount Stop Light (Sedan)
1. Remove the cover by pulling it out. 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the cover. High mount stop light (Se- dan) It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary.
Page 390 Specifications Specifications ... 12-2 Dimensions ... Engine ... Electrical system ... Capacities ... Tires ... Wheel alignment ... Fuses and circuits ... 12-6 Fuse panel located in the passenger compartment ... Fuse panel located in the engine compartment ... Bulb chart ... 12-9 Vehicle identification ...
Page 391: Specifications
12-2 Specifications Specifications These specifications are subject to change without notice. Dimensions Item Overall length Overall width Overall height Wheel base Tread Front Rear Ground clearance Legacy Sedan Station wagon Non- Turbo turbo 2.5-liter 186.2 (4,730) 188.8 (4,795) 68.1 (1,730) 68.1 (1,730) 56.1 (1,425) 58.1 (1,475)
Page 392: Specifications
Engine Engine model (2.5-liter, SOHC, non-turbo) Engine type Horizontally opposed, liquid cooled 4 cylinder, Displacement cu-in (cc) Bore × Stroke in (mm) Compression ratio Firing order Electrical system Battery type and capacity (5HR) 2.5-liter models 3.0-liter models Alternator Spark plugs 2.5-liter non-turbo models 2.5-liter turbo and 3.0-liter models EJ253...
Page 393: Capacities
12-4 Specifications Capacities Fuel tank Engine oil 2.5-liter models 3.0-liter models Transmission oil (MT) Transmission fluid (AT) 2.5-liter non-turbo models 2.5-liter turbo and 3.0-liter models AT differential gear oil 2.5-liter non-turbo models 2.5-liter turbo and 3.0-liter models Rear differential gear oil Power steering fluid Engine coolant 2.5-liter non-turbo models...
Page 394: Tires
Tires Tire size Wheel size Pressure Front 33 psi (230 kPa, 2.3 kgf/cm Rear 32 psi (220 kPa, 2.2 kgf/cm Rear at trailer towing Temporary Size spare tire Pressure Wheel alignment Item Front Rear Camber Front Rear P205/50R17 88V 215/45ZR17 17 ×...
Page 395: Fuses And Circuits
12-6 Specifications Fuses and circuits Fuse panel located in the passenger compart- ment Fuse panel C00004 Fuse rating Cargo fan Trailer hitch connector Empty Door locking Front wiper deicer relay Moonroof Combination meter 7.5A Remote control rear view mirrors Seat heater relay Vanity mirror light Combination meter Integrated unit...
Page 396 Fuse panel Fuse rating Cargo socket Position light Tail light Rear combination light Empty Illumination Seat heaters Backup light 7.5A Headlight right side relay Cigarette lighter socket 7.5A Starter relay Air conditioner Rear window defogger relay coil Rear wiper Rear window washer Audio unit Clock SRS airbag system (Main)
Page 397: Fuse Panel Located In The Engine Compartment
12-8 Specifications Fuse panel located in the engine compartment A) FWD socket (AT vehicles – except Turbo models and 3.0-liter models) B) Main fuse Fuse panel C00005 Fuse rating ABS unit Vehicle dynamics control unit Main fan (3.0-liter models) Sub fan (Except 3.0-liter models) Main fan Audio Headlight (right side)
Page 398: Bulb Chart
Bulb chart Description Wattage Headlight Low beam 12V-55W High beam 12V-60W Front fog light Except OUTBACK 12V-55W OUTBACK 12V-51W Front turn signal/park- 12V-27/8W ing and front side mark- Rear combination light Rear turn signal 12V-21W light (Sedan) Brake/tail and rear 12V-21/5W side marker (Se- dan)
Page 399: Vehicle Identification
12-10 Specifications Vehicle identification Emission control label Vehicle identification number Certification and bar code label Tire inflation pressure label Vehicle identification number plate Model number plate Fuel label C00104...
Page 400: Consumer Information And Reporting Safety Defects
Consumer information and Reporting safety defects Tire information ... 13-2 Tire labeling ... Recommended tire inflation pressure ... Glossary of tire terminology ... Tire care – maintenance and safety practices ... Vehicle load limit – how to determine ... Determining compatibility of tire and vehicle load capacities ...
Page 401: Tire Information
13-2 Consumer information and Reporting safety defects For U.S.A. Consumer information and Reporting safety defects The following information has been com- piled according to Code of Federal Regu- lations “Title 49, Part 575”. Tire information Tire labeling Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers.
Page 402 Example: 205 / 50 R 17 88 V Size designation (6) (7) (6) Load Index: A numerical code which specifies the maximum load a tire can carry at the speed indicated by its speed symbol, at maximum in- flation pressure. For example, “88”...
Page 403 13-4 Consumer information and Reporting safety defects Maximum load rating applies only to the tire, not to the vehi- cle. Putting a load rated tire on any vehicle does not mean the vehicle can be loaded up to the tire’s rated load. Construction type Applicable construction of this tire.
Page 404: Recommended Tire Inflation Pressure
Recommended tire inflation pressure Recommended cold tire inflation pressure Recommended cold tire inflation pressure for your vehicle’s tires is as follows, Tire size Wheel size Pressure Front 33 psi (230 kPa, 2.3 kgf/cm Rear 32 psi (220 kPa, 2.2 kgf/cm Rear at trailer towing Temporary...
Page 405: Glossary Of Tire Terminology
13-6 Consumer information and Reporting safety defects Vehicle placard B00128 The vehicle placard is affixed to the driver’s side B-pillar. Example: TIRE AND LOADING INFORMATION SEATING CAPACITY TOTAL 5 FRONT 2 REAR 3 The combined weight of occupants and cargo should never exceed 385kg or 850lbs.
Page 406: Tire Care - Maintenance And Safety Practices
asymmetrical tire that has a particu- lar side that must always face out- ward when mounting on a vehicle. Accessory weight The combined weight (in excess of those standard items which may be replaced) of floor mats, leather seats and cross bars to the extent that these items are available as factory-in- stalled equipment (whether installed or not).
Page 407: Vehicle Load Limit - How To Determine
13-8 Consumer information and Reporting safety defects Vehicle load limit – how to de- termine The load capacity of your vehicle is determined by weight, not by avail- able cargo space. The load limit of your vehicle is shown on the vehicle placard attached to the driver’s side B-pillar.
Page 408 Example 1B D00112 For example, if a person weighing 176 lbs (80 kg) now enters the same vehi- cle (bringing the number of occupants to two), the calculations are as fol- lows: 1. Calculate the total weight. Total weight = 154 lbs (70 kg) + 176 lbs (80 kg) (Occupant) + 551 lbs (250 kg) (Cargo)
Page 409: Determining Compatibility Of Tire And Vehicle Load Capacities
13-10 Consumer information and Reporting safety defects Available Load Capacity = 800 lbs (363 kg) 628 lbs (285 kg) (Total weight) (Vehicle capacity weight) = 172 lbs (78 kg) 3. The result of step 2 shows that a further 172 lbs (78 kg) of cargo can be carried.
Page 410: Adverse Safety Consequences Of Overloading On Handling And Stopping And On Tires
also loaded capacities of the vehicle’s suspension, axles and other parts of the body. Therefore, this means that the vehicle cannot necessarily be loaded up to the tire’s maximum load rating on the tire sidewall. Adverse safety consequenc- es of overloading on handling and stopping and on tires Overloading could affect vehicle han- dling, stopping distance, vehicle and...
Page 411: Uniform Tire Quality Grading Standards
13-12 Consumer information and Reporting safety defects Uniform tire quality grading standards This information indicates the relative performance of passenger car tires in the area of treadwear, traction, and temperature resistance. This is to aid the consumer in making an informed choice in the purchase of tires.
Page 412: Reporting Safety Defects (Usa)
However, NHTSA can- not become involved in individual problems between you, your deal- er, or Subaru of America, Inc. To contact NHTSA, you may either call the Auto Safety Hotline toll- free at 1-800-424-9393 (or 366- 0123 in the Washington D.C.
Page 414: Index
Index...
Page 415 14-2 Index ABS (Anti-lock Brake System) ... 7-26 Warning light ... 3-20, 7-27 Accessories ... 11-47 Accessory power outlet ... 6-8 Active head restraint ... 1-6 Air cleaner element ... 11-17 Air conditioner ... 4-7 Air filtration system ... 4-13 Air flow selection ...
Page 416 Center Console ... 6-5 Ventilators ... 4-3 Changing Flat tire ... 9-4 Oil and oil filter ... 11-10 Charge warning light ... 3-18 CHECK ENGINE warning light/Malfunction indicator lamp ... 3-17 Checking Brake pedal free play ... 11-30 Brake pedal reserve distance ... 11-30 Clutch function ...
Page 417 14-4 Index Snowy and icy roads ... 8-9 Tips ... 7-11, 7-16, 7-23, 8-5 Tired or sleepy ... 7 Electrical system ... 12-3 Electronic Brake Force Distribution (EBD) system ... 7-28 Emergency Locking Retractor (ELR) ... 1-12 Engine Compartment overview ... 11-6 Coolant ...
Page 418 Illuminated entry ... 2-9 Illumination brightness control ... 3-33 Immobilizer system ... 2-3 Indicator light ... 3-23 Indicator light Cruise control ... 3-25 Cruise control set ... 3-25 Front fog ... 3-25 Headlight ... 3-25 High beam ... 3-25 Selector lever position ... 3-24 Turn signal ...
Page 419 14-6 Index New vehicle break-in driving the first 1,000 miles (1,600 km) ... 8-2 Odometer ... 3-7, 3-11 Off road driving ... 8-6 Oil filter ... 11-10 Oil level Engine ... 11-9 Front differential gear (AT vehicles) ... 11-23 Manual transmission ... 11-20 Rear differential ...
Page 420 Front turn signal light ... 11-50 Headlight ... 11-49 High mount stop light ... 11-56 License plate light ... 11-53 Map light ... 11-54 Parking light ... 11-50 Rear combination light ... 11-51 Trunk light ... 11-55 Rocking the vehicle ... 8-12 Roof rail and crossbar ...
Page 421 14-8 Index Rotation ... 11-37 Tires ... 12-5 Types ... 11-33 Tires and wheels ... 11-33 Top tether anchorages ... 1-36 Towing ... 9-13 All wheels on the ground ... 9-16 Flat-bed truck ... 9-16 Tie-down hooks ... 9-13 Weight ... 8-21 Trailer Hitch ...
Page 422 Replacement ... 11-38 Windows ... 2-19 Windshield Washer fluid ... 11-39 Wiper and washer switches ... 3-35 Wiper deicer ... 3-38 Winter driving ... 8-7 Wiper and washer ... 3-34 14-9 Index...
Page 424 134...
Page 425: Fuel Octane Rating
Fuel: 2.5-liter non-turbo models Use only unleaded gasoline with an octane rating of 87 AKI or higher. 2.5-liter turbo models and 3.0-liter models Use premium unleaded gasoline with an octane rating of 91 AKI or higher. For temporary purposes if premium unleaded gasoline is not available, you may use regular unleaded gasoline with an oc- tane rating of 87 AKI or higher.

This manual is also suitable for:

2006 outback 2006 legacy sedan 2006 legacy station wagon 2006 outback sedan 2006 outback station wagon

Subaru 2006 Legacy Owner's Manual

Table of Contents

Table of Contents

Front Seats

Seat Heater (if Equipped)

Rear Seats

Armrest (if Equipped)

Seatbelts

Front Seatbelt Pretensioners

Child Restraint Systems

SRS Airbag (Supplemental Restraint System Airbag)

Keys and Doors

Keys

Immobilizer

Door Locks

Power Door Locking Switches

Remote Keyless Entry System

Alarm System

Child Safety Locks

Windows

Trunk Lid (Sedan)

Rear Gate (Station Wagon)

Moonroof (if Equipped)

Instruments and Controls

Climate Control

Ventilator

Manual Climate Control System (if Equipped)

Automatic Climate Control System (if Equipped)

Operating Tips for Heater and Air Conditioner

Air Filtration System (if Equipped)

Audio

Antenna System

Installation of Accessories

Audio Set

Type a Audio Set (if Equipped)

Type B Audio Set (if Equipped)

Type C Audio Set (if Equipped)

Audio Control Buttons (if Equipped)

Precautions to Observe When Handling a Compact Disc

MP3 Audio

Interior Equipment

Map Light

Interior Light

Sun Visors

Storage Compartment

Cup Holder

Accessory Power Outlets

Ashtray

Coat Hook

Shopping Bag Hook

Cargo Area Cover (Station Wagon)

Floor Mat

Convenient Tie-Down Hooks (if Equipped)

Stowage Boxes (Station Wagon)

Under-Floor Storage Compartment

Homelink® Wireless Control System (if Equipped)

Starting and Operating

Fuel

State Emission Testing (U.S. Only)

Preparing to Drive

Starting the Engine

Manual Transmission

Stopping the Engine

Automatic Transmission - 4-Speed

Automatic Transmission - 5-Speed

Rear Viscous Limited Slip Differential (LSD) (if Equipped)

Power Steering

Braking

ABS (Anti-Lock Brake System)

Electronic Brake Force Distribution (EBD) System

Vehicle Dynamics Control System (if Equipped)

Tire Pressure Monitoring System (TPMS) (if Equipped)

Parking Your Vehicle

Cruise Control

Quick Links

Chapters

Related Manuals for Subaru 2006 Legacy

Summary of Contents for Subaru 2006 Legacy