Page 1 2002 OWNER S MANUAL Always wear your seatbelt.
Page 2 Foreword Congratulations on choosing a SUBARU vehicle. This Owner’s Manual has all the information necessary to keep your SUBARU in excellent condition and to properly maintain the emission control system for minimizing emission pollutants. We urge you to read this manual carefully so that you may understand your vehicle and its operation.
Page 3 This manual describes the following vehicle types. HGF008AA Sedan HGF009AA Wagon and OUTBACK SPORT...
Page 4 Booklet. Please read these warranties carefully. J Warranties for U.S.A. NOTE All SUBARU vehicles distributed by Subaru of Amer- ica, Inc. and sold at retail by an authorized SUBARU This vehicle does not contain mer- dealer in the United States come with the following warranties: cury devices or parts.
Page 5 Chapter 8: Driving tips Each chapter begins with a brief table of contents, This chapter informs you how to drive your SUBARU so you can usually tell at a glance if that chapter in various conditions and explains some safety tips contains the information you want.
Page 6: Safety Warnings
Please read these safety warnings as well as all oth- er portions of this manual carefully in order to gain a better understanding of how to use your SUBARU vehicle safely. HS0008...
Page 7: Child Safety
Safety precautions when driving the SRS airbag needs enough space for de- ployment, the driver should always sit upright J Seatbelt and SRS airbag and well back in the seat as far from the steer- ing wheel as practical while still maintaining full vehicle control and the front passenger WARNING should move the seat as far back as possible...
Page 8 and weight. If a child is too big for a child re- locks” section in chapter 2. D Always lock the passenger’s windows using straint system, the child should sit in the REAR seat and be restrained using the seat- the lock switch when children are riding in the belts.
Page 9: Drinking And Driving
D If at any time you suspect that exhaust owner’s manual for instructions and precautions concerning the child restraint system, seatbelt sys- fumes are entering the vehicle, have the prob- tem and SRS airbag system. lem checked and corrected as soon as pos- sible.
Page 10 ently, you may have consumed too much alcohol to your doctor. drive safely even if the level of alcohol in your blood Never drive if you are under the influence of any illic- is below the legal limit. The safest thing you can do it mind-altering drugs.
Page 11: Driving With Pets
J Modification of your vehicle J Driving with pets Unrestrained pets can interfere with your driving and distract your attention from driving. In a collision or CAUTION sudden stop, unrestrained pets or cages can be Your vehicle should not be modified. Modifica- thrown around inside the vehicle and hurt you or tion could affect its performance, safety or your passengers.
Page 12: California Proposition 65 Warning
WARNING Driving at high speeds with excessively low tire pressures can cause the tires to deform severely and to rapidly become hot. A sharp increase in temperature could cause tread separation, and destruction of the tires. The resulting loss of vehicle control could lead to an accident.
Page 14: Table Of Contents
Table of contents Seat, seatbelt and SRS airbags Keys and doors Instruments and controls Climate control Audio Interior equipment Starting and operating Driving tips In case of emergency Appearance care Maintenance and service Specifications Consumer information and Reporting safety defects Index –...
Page 15 Illustrated index J Exterior Engine hood (page 11-5) Headlight switch (page 3-15) Replacing bulbs (page 11-56) Wiper switch (page 3-21) Door locks (page 2-3) Tire pressure (page 11-38) Flat tires (page 9-5) Tire chains (page 8-14) Front fog light switch (page 3-19) 10) Tie-down eyes (page 9-15) 11) Towing eye (page 9-15)
Page 16 Rear window defogger switch (page 3-24) Fuel filler lid and cap (page 7-4) Child safety locks (page 2-19) Towing eye (page 9-15) Trunk/Rear gate (page 2-23/2-27) HGF025BB – CONTINUED –...
Page 17 J Interior B Passenger compartment area Lower anchorage for child restraint system (page 1-32) Seatbelt (page 1-11) Parking brake lever (page 7-25) Front seat (page 1-2) Rear seat (page 1-7) HBF030BB...
Page 18 Cup holder (page 6-6) Center console (page 6-5) Glove compartment (page 6-5) Cigarette lighter (page 6-9) Ashtray (page 6-10) HGF031BB – CONTINUED –...
Page 19 J Instrument panel Door locks (page 2-3) Light control lever (page 3-15) Combination meter (page 3-6) Wiper control lever (page 3-20) Hazard warning flasher switch (page 3-5) Audio (page 5-1) Gear shift lever (MT) (page 7-10)/Selector lever (AT) (page 7-13) Outside mirror switch (page 3-28) Climate control (page 4-1)
Page 20 J Light control and wiper control levers/switches Parking light switch (page 3-19) Windshield wiper (page 3-20) Mist (page 3-21) Windshield washer (page 3-21) Rear window wiper and washer switch (page 3-23) Wiper control lever (page 3-21) Illumination brightness control (page 3-18) Light control lever (page 3-15) Headlight ON/OFF (page 3-15) 10) Headlight flasher High/Low...
Page 21 J Combination meter B Overview Fuel gauge (page 3-7) Temperature gauge (page 3-8) Speedometer (page 3-6) Tachometer (page 3-7) Trip meter A/B selection and trip meter reset knob (page 3-6) Odometer and trip meter (page 3-6) Outside temperature indicator (page 3-9) Low fuel warning light (page 3-7) HGF026BB...
Page 22 B Warning and indicator light Mark Name Page Mark Name Page Front-wheel drive warning Seatbelt warning light 3-14 light (if equipped) SRS airbag system warn- 3-10 Turn signal indicator lights 3-14 AIRBAG ing light CHECK ENGINE warning High beam indicator light 3-14 light/Malfunction indicator 3-10...
Page 23 J Tire changing tools Jack (page 9-21) Jack handle (page 9-21) Spare tire (page 9-21) HGF035BB...
Page 24 Seat, seatbelt and SRS airbags Front seats Top tether anchorages 1-35 ............... . SRS airbag Fore and aft adjustment .
Page 25: Seat, Seatbelt And Srs Airbags
Seat, seatbelt and SRS airbags Front seats WARNING D Never adjust the seat while driving to avoid the possibility of loss of vehicle control and of personal injury. D Before adjusting the seat, make sure the hands and feet of rear seat passengers are clear of the adjusting mechanism.
Page 26: Fore And Aft Adjustment
Seat, seatbelt and SRS airbags J Fore and aft adjustment or in a seatbelt, whichever is appropriate for the child’s age, height and weight. Secure ALL types of child restraint devices (including for- ward facing child seat) in the REAR seats at all times.
Page 27: Reclining The Seatback
Seat, seatbelt and SRS airbags J Reclining the seatback WARNING To prevent the passenger from sliding under the seatbelt in the event of a collision, always put the seatback in the upright position while the vehicle is in motion. Also, do not place objects such as cushions between the pas- senger and the seatback.
Page 28: Seat Cushion Height Adjustment
Seat, seatbelt and SRS airbags J Seat cushion height adjustment J Head restraint adjustment (driver’s seat) To raise the head restraint, pull it up. The height of the seat can be adjusted by moving the seat cushion adjustment lever up and down. HB1016BA To lower it, push the head restraint down while HG1003BB...
Page 29: Seat Heater (If Equipped)
Seat, seatbelt and SRS airbags Seat heater (if equipped) HG1007BB 1) HI – Rapid heating 2) LO – Normal heating HG1004BA The indicator located on the switch comes on when The seat heater operates when the ignition switch is the seat heater is in operation. When the vehicle’s in- either in the “...
Page 30: Rear Seats
Seat, seatbelt and SRS airbags D Do not put anything on the seat which insu- Rear seats lates against heat, such as a blanket, cushion, or similar items. This may cause the seat heat- er to overheat. WARNING NOTE Seatbelts provide maximum restraint when D Use of the seat heater for a long period of time the occupant sits well back and upright in the seat.
Page 31: Armrest (If Equipped)
Seat, seatbelt and SRS airbags J Armrest (if equipped) WARNING D Never allow passengers to ride on the folded rear seatback or in the cargo area. Do- ing so may result in serious injury or death. D Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or accident.
Page 32: Folding Down The Rear Seat - Wagon
Seat, seatbelt and SRS airbags B Loading long objects operation of the car, possibly causing an acci- dent and serious injury. HG1029BA Folding down the armrest and opening the seatback HG1009BA panel affords a loading space for long objects. To open the seatback panel, pull the release tab. J Folding down the rear seat –...
Page 33: Headrest Adjustment (If Equipped)
Seat, seatbelt and SRS airbags D Secure skis and other lengthy items properly Unlock the seatback by pulling the release knob to prevent them from shooting forward and and then fold the seatback down. causing serious injury during a sudden stop. J Headrest adjustment (if equipped) HB1022BA HS1013CA...
Page 34: Seatbelts
Seat, seatbelt and SRS airbags pecially if they are 12 years of age and under Seatbelts and are not restrained or improperly re- J Seatbelt safety tips strained. Because children are lighter and weaker than adults, their risk of being injured WARNING from deployment is greater.
Page 35: Emergency Locking Retractor (Elr)
Seat, seatbelt and SRS airbags B Infants or small children and as low as possible over the hips, not over the waist. Use a child restraint system that is suitable for your vehicle. See information on “ Child restraint systems” J Emergency Locking Retractor (ELR) in this chapter.
Page 36: Seatbelt Warning Light And Chime
Seat, seatbelt and SRS airbags J Fastening the seatbelt When securing a child restraint system on the rear seats by the use of the seatbelt, the seatbelt must be changed over to the Automatic Locking Retractor WARNING (ALR) mode. D Never use a belt that is twisted or reversed. When the child restraint system is removed, make In an accident, this can increase the risk or sure that the seatbelt retracts fully and the retractor...
Page 37 Seat, seatbelt and SRS airbags B Front seatbelts can result in serious internal injury or death. D Never place the shoulder belt under the arm 1. Adjust the seat position: or behind the back. If an accident occurs, this Driver’s seat: Adjust the seatback to the upright can increase the risk or severity of injury.
Page 38 Seat, seatbelt and SRS airbags n Adjusting the front seat shoulder belt anchor height The shoulder belt anchor height should be adjusted to the position best suited for you. To lower the an- chor height, push the release button and slide the anchor down.
Page 39 Seat, seatbelt and SRS airbags bing in the door. WARNING B Rear seatbelts (except rear center seatbelt on When wearing the seatbelts, make sure the Wagon) shoulder portion of the webbing does not 1. Sit well back in the seat. pass over your neck.
Page 40 Seat, seatbelt and SRS airbags 2) Place the lap belt as low as possible on your hips, not on your waist. HS1020BA Always adjust the anchor height so that the shoulder OM-H0044 belt passes over the middle of the shoulder without touching the neck.
Page 41 Seat, seatbelt and SRS airbags n Unfastening the seatbelt plate into the mating buckle (on right-hand side), always check that the webbing is not Push the button on the buckle. twisted. HB0303 HB1030BA Before closing the door, make sure that the belts are retracted properly to avoid catching the belt web- bing in the door.
Page 42 Seat, seatbelt and SRS airbags HG1012BA HG1023BA 1. Remove the tongue plate from the belt holder lo- cated under the right rear quarter glass and pull out the seatbelt slowly. HS1017BB 1) Center seatbelt tongue plate 2) Connector (tongue) HG1027BA 3) Connector (buckle) 4) Center seatbelt buckle –...
Page 43 Seat, seatbelt and SRS airbags 2. After drawing out the seatbelt, pass it through the 4. Insert the center seatbelt tongue plate in the cen- belt guide as follows: First insert one edge of the ter seatbelt buckle marked “ CENTER” on the left- belt into the open gap in the comfort guide;...
Page 44 Seat, seatbelt and SRS airbags 5. 1) To make the lap part tight, pull up on the n Unfastening the seatbelt shoulder belt. 2) Place the lap belt as low as possible on your hips, not on your waist. HS0317 Push the release button of the center seatbelt buckle (on the left-hand side) to unfasten the seat- HGS037BC...
Page 45 Seat, seatbelt and SRS airbags disconnect from the buckle. HS1021BA HG1024BA 2. Allow the retractor to roll up the belt. You should hold the webbing end and guide it back into the re- tractor while it is rolling up. Insert the tongue plate into the belt holder.
Page 46: Seatbelt Maintenance
Seat, seatbelt and SRS airbags trim during driving, causing damage to the CAUTION trim. D Keep the belts free of polishes, oils, chemi- cals and particularly battery acid. D Never attempt to make modifications or changes that will prevent the seatbelt from op- erating properly.
Page 47: Front Seatbelt Pretensioners
In the event that a preten- sioner is activated, both the driver’s and front passenger’s seatbelt retractor assemblies must be replaced only by an authorized SUBARU dealer. When replacing seatbelt retractor assem- blies, use only genuine SUBARU parts.
Page 48: System Monitors
Seat, seatbelt and SRS airbags J System monitors SUBARU dealer as soon as possible. D When you sell your vehicle, we urge you to explain to the buyer that it has seatbelt preten- sioners by alerting him to the contents of this section.
Page 49: System Servicing
SRS airbag nearest SUBARU dealer to have the system systems. For required servicing of the seat- checked. Unless checked and repaired, the seatbelt...
Page 50: Precautions Against Vehicle Modification
According to accident statistics, children are safer when properly restrained in the rear seating posi- tions than in the front seating positions. Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle. – CONTINUED –...
Page 51 Seat, seatbelt and SRS airbags All U.S. states and Canadian provinces require that WARNING infants and small children be restrained in an approved child restraint system at all times while the Never let a passenger hold a child on his or vehicle is moving.
Page 52 Seat, seatbelt and SRS airbags WARNING WARNING Children should be properly restrained at all Put children aged 12 and under in the rear times. Never allow a child to stand up, or to seat properly restrained at all times. The SRS kneel on any seat.
Page 53 Seat, seatbelt and SRS airbags HS1031BA HS0042 WARNING WARNING D Child restraint systems and seatbelts can SINCE YOUR VEHICLE IS EQUIPPED WITH A PASSENGER’S AIRBAG, NEVER become hot in a vehicle that has been closed INSTALL A REARWARD FACING CHILD SAFE- up in sunny weather;...
Page 54: Installing Child Restraint Systems With
Seat, seatbelt and SRS airbags J Installing child restraint systems with into the retractor. As the belt is rewinding, clicks will be heard which indicate the retractor functions as seatbelt ALR. 6. Before having a child sit in the child restraint sys- tem, move it back and forth to check if it is firmly secured.
Page 55: Installation Of Child Restraint Systems By
If you have any question concerning this type of of the seatbelts. Such child restraint systems are se- child restraint system, ask your SUBARU dealer. cured to the dedicated anchorages provided on the vehicle body.
Page 56 Seat, seatbelt and SRS airbags HB1090BA HG1030BA The lower anchorages (bars) are used for installing The tether anchorages (upper anchorages) are pro- a child restraint system only on the rear seat win- vided for all the seating positions (middle and both dow-side seating positions.
Page 57 If you have any question concerning this type of child restraint system, ask your SUBARU dealer. HB1088BA Each lower anchorage is located where the seat WARNING cushion meets the seatback.
Page 58: Top Tether Anchorages
Seat, seatbelt and SRS airbags J Top tether anchorages B Anchorage location HG1031BB 1) For left seat HG1032BB 2) For center seat 3) For right seat 1) For left seat Sedan: Three anchorages are installed on the rear 2) For center seat 3) For right seat parcel shelf.
Page 59 Seat, seatbelt and SRS airbags Wagon: There is an anchorage for the center seat- n Wagon ing position at the rear end of the ceiling, and anchorages for each of the two window-side seating positions on the rear wall of the cargo area. B To hook the top tether n Sedan HGS031BA...
Page 60 Seat, seatbelt and SRS airbags HGS032BB HGS033BB Center Window-side F: Front of vehicle F: Front of vehicle 1) Top tether hook 1) Top tether hook 2) Upper anchorage 2) Upper anchorage 2. Fasten the top tether hook of the child restraint system to the appropriate upper anchorage.
Page 61: Srs Airbag
Seat, seatbelt and SRS airbags *SRS airbag (Supplemental Restraint protection provided by the seatbelt. It does not do away with the need to fasten seatbelts. System airbag) In combination with the seatbelts, it offers the best combined protection in case of a serious *SRS: This stands for supplemental restraint system.
Page 62 Seat, seatbelt and SRS airbags deployment force. D The SRS airbags deploy with considerable speed and force. Occupants who are out of proper position when the SRS airbag deploys could suffer very serious injuries. Because the SRS airbag needs enough space for de- ployment, the driver should always sit upright and well back in the seat as far from the steer- ing wheel as practical while still maintaining...
Page 63 Seat, seatbelt and SRS airbags strained at all times in a child restraint device CAUTION or in a seatbelt, whichever is appropriate for D When the SRS airbag deploys, some smoke the child’s age, height and weight. Secure ALL types of child restraint devices will be released.
Page 64 Seat, seatbelt and SRS airbags Airbag control module (including impact sensors) Airbag module (driver’s side) Airbag module (passenger’s side) Front sub sensor (left hand side) Front sub sensor (right hand side) Side airbag module (driver’s side — if equipped) Side airbag module (passenger’s side —...
Page 65: Srs Frontal Airbag
Seat, seatbelt and SRS airbags J SRS frontal airbag WARNING Never allow a child to stand up, or to kneel on WARNING the front passenger’s seat, or never hold a child on your lap or in your arms. The SRS air- NEVER INSTALL A REARWARD FACING bag deploys with considerable force and can...
Page 66 Seat, seatbelt and SRS airbags SRS airbag contacts an occupant not in prop- er position such as one thrown toward the front of the car during pre-accident braking. HG1013BA WARNING HG1001BA The SRS airbag deploys with considerable speed and force. Occupants who are out of The driver’s SRS frontal airbag is stowed in the cen- proper position when the SRS airbag deploys ter portion of the steering wheel.
Page 67 Seat, seatbelt and SRS airbags WARNING WARNING Do not put any objects over the steering Do not attach accessories to the windshield, wheel pad and dashboard. If the SRS frontal or fit an extra-wide mirror over the rear view airbag deploys, those objects could interfere mirror.
Page 68 Seat, seatbelt and SRS airbags B Operation The front passenger’s SRS frontal airbag deploys to- gether with driver’s SRS frontal airbag even when no The SRS airbag can function only when the ignition one occupies the front passenger’s seat. switch is in the “ ON” position. Although it is highly unlikely that the SRS airbag If the front sub sensors inside the both front fenders would activate in a non-accident situation, should it...
Page 69 Seat, seatbelt and SRS airbags HS2001BB 1-46...
Page 70 Seat, seatbelt and SRS airbags When the SRS airbag deploys, a sudden, fairly loud force experienced in the passenger compartment inflation noise will be heard and some smoke will be during a collision. That level differs from one type of released.
Page 71 Seat, seatbelt and SRS airbags n At what other times might the SRS frontal air- The SRS frontal airbag may be activated when the bag deploy? vehicle sustains a hard impact in the undercarriage area from the road surface (such as when the ve- hicle plunges into a deep ditch, is severely bumped or knocked hard against an obstacle on the road such as a curb).
Page 72 Seat, seatbelt and SRS airbags n When is the SRS frontal airbag unlikely to There are many types of collisions which might not deploy? necessarily require SRS frontal airbag deployment. If the vehicle strikes an object, such as a telephone pole or sign pole, or if it slides under a truck’s load bed, or if it sustains an oblique offset frontal impact, the SRS frontal airbag may not deploy depending on...
Page 73 Seat, seatbelt and SRS airbags n When will the SRS frontal airbag not deploy? The SRS frontal airbag is basically not designed to deploy if the vehicle is struck from side or from behind, or if it rolls onto its side or roof, or if it is in- volved in a low-speed frontal collision.
Page 74: Srs Side Airbag (If Equipped)
Seat, seatbelt and SRS airbags J SRS side airbag (if equipped) WARNING D The SRS side airbag is designed as only a supplement to the primary protection pro- vided by the seatbelt. It does not do away with the need to fasten seatbelts. It is also impor- tant to wear your seatbelt to help avoid inju- ries that can result when an occupant is not seated in a proper upright position.
Page 75 Seat, seatbelt and SRS airbags HS0351 HB0354 WARNING Never allow a child to kneel on the front pas- senger’s seat facing the side window or to wrap his/her arms around the front seatback. In the event of an accident, the force of the SRS side airbag deployment could injure the child seriously because his/her head or arms or other body parts are too close to the SRS...
Page 76 Seat, seatbelt and SRS airbags WARNING WARNING Do not attach accessories to the door trim or Do not put any kind of cover or clothes or oth- near either SRS side airbags and do not place er objects over either front seatback and do objects near the SRS side airbags.
Page 77 Seat, seatbelt and SRS airbags B Operation deploys between the occupant and the door panel and supplements the seatbelt by reducing the im- The SRS side airbag can function only when the pact on the occupant’s chest. ignition switch is in the “ ON” position. The driver’s and front passenger’s SRS side airbags deploy independently of each other since each has its own impact sensor.
Page 78 Seat, seatbelt and SRS airbags The SRS side airbag deploys even when no one oc- cupies the seat on the side on which an impact is applied. When the SRS side airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be released.
Page 79 Seat, seatbelt and SRS airbags of force experienced in the passenger compartment n When is the SRS side airbag unlikely to during a side impact collision. That level differs from deploy? one type of collision to another, and it may have no There are many types of collisions which might not bearing on the visible damage done to the vehicle necessarily require SRS side airbag deployment.
Page 80 Seat, seatbelt and SRS airbags 1) The vehicle is involved in an oblique side-on impact. 2) The vehicle is involved in a side-on impact in an area outside the pas- senger compartment. 3) The vehicle strikes a telephone pole or similar object. 4) The vehicle is involved in a side-on impact from a motorcycle.
Page 81 Seat, seatbelt and SRS airbags n When will the SRS side airbag not deploy? The SRS side airbag is basically not designed to deploy if the vehicle is involved in a frontal collision or is struck from behind. Examples of such acci- dents are illustrated.
Page 82: Srs Airbag System Monitors
D All related wiring In the event of a malfunction indicated by any of fol- lowing, the vehicle should be taken promptly to your nearest SUBARU dealer to have the system checked. Unless checked and repaired, the SRS airbags will not function reliably: D Flashing or flickering of the indicator light.
Page 83: Srs Airbag System Servicing
SUBARU parts. To ensure their long-term reliability, the SRS airbags must be inspected by a SUBARU dealer ten years after the date of manufacture, which is shown on the certification plate attached to the driver’s door jamb.
Page 84: Precautions Against Vehicle Modification
Seat, seatbelt and SRS airbags J Precautions against vehicle modifica- NOTE In the following cases, contact your SUBARU tion dealer as soon as possible. D The front part of the vehicle was involved in an WARNING accident in which the SRS frontal airbags did not deploy.
Page 85 D Attachment of any equipment (side steps or side sill protectors, etc.) other than SUBARU genuine accessory parts to the side body (for vehicles with side airbags only). Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle. 1-62...
Page 86 Keys and doors Keys To cancel the trunk lid release 2-24 ............... Trunk lid release handle 2-25 Key number...
Page 87: Keys And Doors
Keys and doors Keys locks. You can keep the trunk and glove compart- ment locked when you leave your vehicle and valet key at a parking facility. J Key number The key number is stamped on the metal plate attached to the key set. Write down the key number and keep it in another safe place, not in the vehicle.
Page 88: Door Locks
Keys and doors Door locks J Locking and unlocking from the out- side HB2024BC 1) Rotate the lock lever rearward. 2) Close the door. To lock the door from the outside without the key, rotate the lock lever rearward and then close the HS0010 door.
Page 89 Keys and doors NOTE Pull the inside door handle to open an unlocked door. Make sure that you do not leave the key inside the vehicle when locking the doors from the out- Always make sure that all doors and the rear gate side without the key.
Page 90: Power Door Locking Switches (If Equipped)
Keys and doors Power door locking switches NOTE Make sure that you do not leave the key inside (if equipped) the vehicle before locking the doors from the outside using power door locking switches. HG2012BB 1) Lock 2) Unlock All doors and the rear gate (wagon) can be locked and unlocked by the power door locking switches located at the driver’s side and the front passenger’s side doors.
Page 91: Keyless Entry System (If Equipped)
Keys and doors Keyless entry system (if equipped) The operable distance of the keyless entry system is approximately 30 feet (10 meters). However, this distance will vary depending on environmental Two transmitters are provided for your vehicle. conditions. Range may be reduced near sources of The keyless entry system has the following func- RF interference such as power plants and radio/tele- tions.
Page 92: Sounding A Panic Alarm
Keys and doors that the doors (or the rear gate) are not properly closed. When you close the door, it will automatically lock. J Unlocking the doors Briefly press the “ UNLOCK/DISARM” button (for less than two seconds) to unlock the driver’s door. The horn will sound two times.
Page 93: Selecting Audible Signal Operation
Keys and doors “ UNLOCK/DISARM” button. Unless a button on the To replace the battery: remote is pressed, the alarm will be deactivated after approximately 30 seconds. J Selecting audible signal operation Using the horn, the system will give you an audible signal when the doors lock and unlock.
Page 94: Replacing Lost Transmitters
Keys and doors CAUTION Do not let dust, oil or water get on or in the transmitter when replacing the battery. J Replacing lost transmitters If you lose a transmitter or want to purchase addi- tional transmitters (up to four can be programmed), you should re-program all of your transmitters for security reasons.
Page 95 Keys and doors To enter the programming mode: HB1005BC HB1000CA 2. Open the driver’s door and sit in the driver’s seat. 3. Close the driver’s door. 1. Press “ UNLOCK/DISARM” button to disarm the security system. (If your vehicle is equipped with the optional security system.) HB2032BC 1) ON...
Page 96 Keys and doors 4. Place the ignition key into the ignition switch and cycle the switch from LOCK to ON ten times within 15 seconds. Be sure to stop at the LOCK position. The horn will sound once to indicate that you are in the transmitter programming mode.
Page 97: System Operation
Keys and doors operates by operating each transmitter. Security system (if equipped) B Deleting old transmitter codes The security system helps to protect your vehicle The control unit of the keyless entry system has four and valuables from theft. The horn sounds and the memory locations to store transmitter codes, giving parking lights flash if someone attempts to break it the ability to operate with up to four transmitters.
Page 98: Arming The System
Keys and doors breaking glass or forced entry). Note that there are two alarm levels for shock: warning and alarm. In warning mode, the alarm detects lower level vibra- tions and triggers 2 warning chirps on the horn and two flashes on the lights as a deterrent to would be vandals.
Page 99 Keys and doors 6. Briefly press the “ LOCK/ARM” button (for less than two seconds). All doors (and the rear gate on the wagon) will lock, the horn will sound one time, the parking lights will flash one time and the indica- tor light starts flashing slowly (approximately once every two seconds).
Page 100: Sounding A Panic Alarm
Keys and doors J Disarming the system To deactivate it, press the “ LOCK/ARM” button or “ UNLOCK/DISARM” button. Briefly press the “ UNLOCK/DISARM” button (for less The parking lights will also flash when the alarm is than two seconds) on the remote transmitter. The activated.
Page 101 Keys and doors Note that in this mode, DOORS MUST BE MANUAL- LY LOCKED. B To enter the passive mode HB2038BC 1) Connector for SRS airbag system (yel- low) 2) Blue (1P) HB2036BA 2. Connect the blue (1 pole) connector. 1.
Page 102 Keys and doors 2. Turn the ignition switch from “ ON” to “ LOCK” WARNING position and remove the key from the ignition switch. Do not disconnect or tamper with any yellow connector and/or any harness covered with yellow insulation and/or tape. Doing so could result in accidental inflation of the SRS airbag or could make the SRS airbag system inoperative, which may result in seri-...
Page 103 Keys and doors The indicator light provides the following indications. CAUTION Flashing one time: Any door, the rear gate or the trunk lid has been opened. In passive mode, the system will automatically Flashing three times: The impact sensor in the sys- activate the alarm but WILL NOT automatically tem’s unit has been activated.
Page 104: Child Safety Locks
Keys and doors Child safety locks WARNING Always use the child safety lock whenever a Each rear door has a child safety lock that prevents child rides in the rear seat. Serious injury the doors from being opened even if the inside door could result if a child accidentally opened the handle is pulled.
Page 105: Windows
Keys and doors B Driver’s side switches Windows J Power windows WARNING D When operating the power windows, be ex- tremely careful to prevent anyone’s fingers, arms or head from being caught in the win- dow. D Always lock the passengers’ windows using the lock switch when children are riding in the HG2016BB vehicle.
Page 106 Keys and doors n Operating the driver’s window n Operating the passengers’ windows HG2008DB HG2008CA 1) Open To open the passengers’ windows, push the ap- 2) Automatically open propriate switch down and hold it until the window 3) Close reaches the desired position. To close the window, pull the switch up and hold it until it reaches the de- AUTO switch: This switch has two functions.
Page 107 Keys and doors n Locking the passengers’ windows “ LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches. HG2013BB 1) Lock 2) Unlock To lock the passengers’ windows, push the lock switch. When the lock switch is in the “ LOCK” posi- tion, the passengers’...
Page 108: Trunk Lid (Sedan)
Keys and doors J To open and close the trunk lid from Trunk lid (Sedan) outside WARNING D To prevent dangerous exhaust gas from en- tering the vehicle, always keep the trunk lid closed while driving. D Help prevent young children from locking themselves in the trunk.
Page 109: To Open The Trunk Lid From Inside
Keys and doors J To open the trunk lid from inside J To cancel the trunk lid release HB3000CC HG2009BA 1) Open The inside trunk lid release can be cancelled to help prevent unauthorized entry into the trunk. To cancel Pull the trunk lid release lever upward.
Page 110: Trunk Lid Release Handle
Keys and doors J Trunk lid release handle short time. The trunk lid release handle is a device designed to WARNING open the trunk lid from inside the trunk. In the event children or adults become locked inside the trunk, Never allow any child to get in the trunk and the handle allows them to open the lid.
Page 111 Keys and doors B Inspection Perform the following steps at least twice a year to check the release handle for correct operation. 1. Open the trunk lid. 2. Use a screwdriver with a thin blade. Slide the screwdriver blade from the slit aperture of the lock assembly fully to the end until you hear a click.
Page 112: Rear Gate (Wagon)
Keys and doors If the latch is not released, contact your SUBARU Rear gate (Wagon) dealer. In that case, use the key to release the latch, then close the trunk lid. Also, if the movements of the release handle feel re-...
Page 113 Keys and doors latch engages. WARNING To prevent dangerous exhaust gas from enter- ing the vehicle, always keep the rear gate closed while driving. 2-28...
Page 114 Instruments and controls Ignition switch Front-wheel drive warning light ........(for AT vehicles –...
Page 115: Instruments And Controls
Instruments and controls B Automatic transmission vehicles Ignition switch HB4016BA HB3014BA The ignition switch has four positions: LOCK, ACC, ON and START. J LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key.
Page 116: Acc
Instruments and controls J ACC when the selector lever is in the “ P” position. B Manual transmission vehicles In this position the electrical accessories (radio, cig- arette lighter, etc.) can be used. J ON This is the normal operating position after the engine is started.
Page 117 Instruments and controls J Key interlock release (AT vehicles only) If the key can not be turned to the “ LOCK” position even when the selector lever is in the “ P” position: 1. Take out the screwdriver from the tool bag. HB3012BA HB3011BA 2.
Page 118: Hazard Warning Flasher
Instruments and controls Hazard warning flasher Take your vehicle to the nearest SUBARU dealer im- mediately to have the key interlock system repaired. HG3004AA The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions.
Page 119: Meters And Gauges
Instruments and controls B Double trip meter Meters and gauges J Speedometer The speedometer shows the vehicle speed. J Odometer/Trip meter HG3006BB 1) A trip meter 2) B trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the HG3005BB knob.
Page 120: Fuel Gauge
Instruments and controls J Fuel gauge CAUTION To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result. NOTE If the connection between the combination meter and battery is broken for any reason such as ve- hicle maintenance or fuse replacement, the data recorded on the trip meter will be lost.
Page 121: Fuel Gauge
Instruments and controls NOTE about 4.0 U.S. gal. (15 liters, 3.3 Imp. gal.). J Temperature gauge HG3016AA You will see the “ FUEL DOOR p” sign near the HG3008BB fuel gauge. This indicates that the fuel filter door (lid) is 1) Normal operating range located on the right side of the vehicle.
Page 122: (If Equipped)
D When there is too much sun. bulb or a malfunction of the corresponding system. D During idling; while running at low speeds in a Consult your authorized SUBARU dealer for repair. traffic jam; when the engine is restarted immediately following a shutdown.
Page 123: Check Engine Warning Light
If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/re- J SRS airbag system warning paired by your SUBARU dealer as soon as light AIRBAG possible. Continued vehicle operation without having the emission control system checked When the ignition switch is turned to the “...
Page 124: Charge Warning Light
If the light does not go after the engine starts, stop the engine at the first out, take your vehicle to your authorized SUBARU safe opportunity and check the alternator belt. If the dealer immediately.
Page 125: At Oil Temperature Warning
If these occur, have the ABS system repaired is not working properly. Contact your nearest at the first available opportunity by your SUBARU dealer for service immediately. SUBARU dealer. (U.S.) J ABS warning light...
Page 126: Door Open Warning Lights
The door open warning light comes on if any door or by a SUBARU dealer immediately. the rear gate is not fully closed. D If at all in doubt about whether the brakes –...
Page 127: Turn Signal Indicator Lights
Instruments and controls Always make sure this light is out before you start to Clock drive. J Front-wheel drive warning light (for AT vehicles – if equipped) This light comes on when All Wheel Drive is disen- gaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar purposes.
Page 128: Light Control Switch
Instruments and controls J Headlights Light control switch The light switch operates only when the ignition switch is in the “ ON” position. WARNING To prevent battery discharge resulting from accidentally leaving your lights on when your vehicle is parked, the light switch operates only when the ignition switch is in the “...
Page 129: Headlight Flasher
Instruments and controls J High/low beam change (dimmer) J Headlight flasher HG3014CA HG3014BA To change from low beam to high beam, push the To flash the headlights, pull the lever toward you and turn signal lever forward. When the headlights are then release it.
Page 130: Turn Signal Lever
Instruments and controls J Daytime running light system Turn signal lever WARNING The tail lights, parking lights, and side marker lights are not turned on by the daytime run- ning light system. The light switch must al- ways be turned to the “ a” position when it is dark outside.
Page 131: Illumination Brightness Control
Instruments and controls the direction of the turn or lane change. The lever Illumination brightness control will return automatically to the neutral position when you release it. When the lighting switch is in the “ p” or “ a” position, you can adjust brightness of the instrument panel illumination for better visibility.
Page 132: Parking Light Switch
Instruments and controls Parking light switch Fog light switch (if equipped) The fog lights operate only when the headlights are on low beam. Push the fog light switch to turn the fog lights on. Press the switch again to turn them off. HB2018BA The parking light switch operates regardless of the ignition switch position.
Page 133: Wiper And Washer
In areas where water freezes in D Do not operate the wipers when the wind- winter, use SUBARU Windshield Washer Fluid shield or rear window is dry. This may scratch or the equivalent. (See the “ Windshield wash- the glass, damage the wiper blades and cause er fluid”...
Page 134: Windshield Wiper And Washer
Instruments and controls This will cause deterioration of the wiper blades with new ones. Refer to the “ Wiper blade blades. replacement” section (chapter 11) for replace- ment instructions. NOTE J Windshield wiper and washer D The wiper operates only when the ignition switch is in the “...
Page 135 Instruments and controls B Mist (for a single wipe) To turn the wipers off, return the lever to the “ OFF” position. B Wiper intermittent time control (if equipped) HG3011BA For a single wipe of the wipers, pull the lever toward HB2023BA you.
Page 136: Rear Window Wiper And Washer
Instruments and controls J Rear window wiper and washer B Washer switch (if equipped) HB2020BA HB2021BB To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid 1) Rear wiper 2) Washer sprays until you release the washer button.
Page 137: Rear Window Defogger Switch
Instruments and controls washer fluid sprays until you release the knob. Rear window defogger switch To wash the rear window when the rear wiper is not in use, turn the knob on the end of the wiper control The rear window defogger operates only when the lever clockwise to the “...
Page 138: Mirrors
Instruments and controls To turn on the defogger, push the switch. To turn it Mirrors off, push the switch again. The indicator light located on the switch lights up Always check that the inside and outside mirrors are while the rear window defogger is operating. properly adjusted before you start driving.
Page 139 Instruments and controls B Compass mirror (if equipped) D By pressing and releasing the right button, the compass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror. Even with the mirror in anti-glare mode, the mirror surface turns bright if the transmission is shifted into reverse.
Page 140 Instruments and controls blinded. For this reason, use care not to cover the n Compass zone adjustment sensors with stickers, or other similar items. Periodi- cally wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. n Compass calibration 1.
Page 141: Outside Mirrors
Instruments and controls 4. Releasing the button for 3 seconds will exit the tance of objects that you view in convex mir- zone setting mode. ror. J Outside mirrors B Remote control mirror switch The remote control mirrors operate only when the ignition switch is in the “...
Page 142 Instruments and controls The mirrors can also be adjusted manually. 15 minutes. If the mirror clears before that time, push the switch to turn it off. It also turns off when B Outside mirror defogger (if equipped) the ignition switch is turned to the “ ACC” or “ LOCK” The outside mirror defogger shares the switch with position.
Page 143: Tilt Steering Wheel
Instruments and controls Tilt steering wheel WARNING Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury. HB4002BA 1. Adjust the seat position. Refer to the “ Front seat” section (chapter 1).
Page 144: Horn
Instruments and controls Horn OM-H0440 To sound the horn, push the horn pad. – CONTINUED – 3-31...
Page 146: Climate Control
Climate control Ventilator ..........Air flow selection .
Page 147: Climate Control
Climate control Ventilator J Air flow selection HG4003BA...
Page 148: Center And Side Ventilators
Climate control J Center and side ventilators B Side ventilators B Center ventilators HG4031BB 1) Open 2) Close HG4030BA Move the knob in any direction you prefer to adjust Move the tab up and down or right and left to adjust the flow direction.
Page 149: Climate Control System
Climate control Climate control system to red side (warm). B Fan speed control dial J Control panel The fan operates only when the ignition switch is turned to the “ ON” position. The fan speed control dial is used to select four fan speeds. B Air flow control dial This dial has the following five positions: : Air flows through the instrument panel out-...
Page 150: Heater Operation
Climate control B Air conditioner button (if equipped) WARNING Continued operation in the position may fog up the windows. Switch to the posi- tion as soon as the outside dusty condition clears. J Heater operation B Defrosting or defogging the windshield HB5010BB 1) Push The air conditioner operates only when the engine is...
Page 151 Climate control 2. Set the air flow control dial to the “ ” position. To direct warm air toward the floor and the wind- 3. Turn the temperature control dial all the way to shield: the right. 1. Set the air inlet selection lever to the “ ”...
Page 152 Climate control To direct warm air toward the floor: This setting allows you to direct air of different tem- 1. Set the air inlet selection lever to the “ ” peratures from the instrument panel and foot outlets. position The air from the foot outlets is slightly warmer than 2.
Page 153: Air Conditioner Operation
Climate control B Ventilation WARNING Continued operation in the “ ” position may fog up the windows. Switch to the “ ” position as soon as the outside dusty condition clears. J Air conditioner operation B Cooling or dehumidifying HG4027AA To force outside air through the instrument panel outlets: 1.
Page 154 Climate control 1. Set the air inlet selection lever to the “ ” posi- tion. tion. 3. Set the air conditioner button to the “ ON” posi- 2. Set the air flow control dial to the “ ” position. tion. 3.
Page 155: Cleaning Ventilator Grille
This check is best performed by your SUBARU paired by any accumulation of insects and leaves dealer.
Page 156 Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the method of adding, chang- ing or checking the refrigerant is different from the method for CFC12 (Freon). Consult your SUBARU dealer for service. Repairs needed as a result of – CONTINUED –...
Page 157: Air Filtration System (If Equipped)
Since the filter element is a viscous type, it is unnecessary to clean or wash the element. Have your filter checked or replaced by your SUBARU dealer. Replacement schedule: Every 12 months or 7,500 miles (12,000 km) whichever comes first...
Page 158: Audio
Audio Antenna system ........FM reception .
Page 159: Antenna System
Audio Antenna system Installation of accessories Always consult your SUBARU dealer before instal- ling a citizen band radio or other transmitting device in your vehicle. Such devices may cause the elec- tronic control system to malfunction if they are incor- rectly installed or if they are not suited for the ve- hicle.
Page 160: Type B Audio Set
Audio J Type B audio set Audio set Your SUBARU may be equipped with one of the fol- lowing audio sets. See the pages indicated in this section for operating details. J Type A audio set HS5004AA D Radio operation: refer to page 5-14...
Page 161: Radio Operation
Audio Type A audio set (if equipped) The radio will operate only when the ignition switch is in the “ ACC” or “ ON” position. J Radio operation (1) SCAN button (2) Power switch, Volume control, Bass/Middle/Treble control and Fader/Balance control dial (3) Tuning buttons (4) FM/AM selection button (5) Preset buttons...
Page 162 Audio B Power switch and volume/bass/treble/fader/ To change control modes: Each brief press of the balance control (PWR/VOL) “ T/B” button changes control modes in the following sequence starting from volume control mode. (When The dial (2) is used for both power (ON/OFF) and the radio is first turned on, the control mode is in the volume control.
Page 163 Audio Display Control mode HB5036BA Turn counterclockwise Turn clockwise Bass control For less bass For more bass Treble control For less treble For more treble Balance con- To increase left speaker volume and decrease To increase right speaker volume and trol right speaker volume decrease left speaker volume...
Page 164 Audio from the low end to the high end. Press the “ SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “ SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low The display indicates which one is currently frequencies to high frequencies only.
Page 165: Compact Disc Player Operation
Audio NOTE preset buttons are cleared. If this occurs, it is necessary to reset the preset buttons. If the connection between the radio and battery is broken for any reason such as vehicle mainte- nance or radio removal, all stations stored in the J Compact disc player operation (7) Eject button (8) Disc slot...
Page 166 Audio B To play back a compact disc B To select a song from its beginning n When CD is not in the player n Forward direction ∧ Hold a disc with a finger in the center hole while Briefly press the “ ”...
Page 167 An optional CD changer can be connected to this B Random playback audio unit. See your SUBARU dealer for more information. Press the “ RPT/RDM” button (10) and hold it in for more than 2 seconds while a disc is being played back to play all songs on the disc in a random order.
Page 168 Audio (12) Track selection buttons (13) DISC button (14) Repeat/Randam button (15) Disc selection button HG5008DB – CONTINUED – 5-11...
Page 169 Audio B To start playback azines can also be selected in a similar way. When the “ CD” button (13) is pressed, the CD NOTE changer will start playback. The display shows the D No disc change takes place if the button corre- current disc number, track number and the elapsed sponding to the magazine slot in which no disc time during playback.
Page 170 Audio the CD changer will automatically stop fast forward- To cancel the random mode, press the button again. ing and start playback beginning with the first track Then the “ RDM” indicator goes out, and normal on the current disc. playback mode is restored.
Page 171 Audio Type B audio set (if equipped) The radio will operate only when the ignition switch is in the “ ACC” or “ ON” position. J Radio operation (1) FM button (2) AM button (3) SCAN button (4) Tuning knob (5) Preset buttons (6) Fader/Balance selection button (7) Power switch, Volume control,...
Page 172 Audio B Power switch and volume/bass/treble/fader/ This dial is used for bass/treble controls when the balance control (PWR/VOL) “ BAS/TRE” button (8) is in the depressed position. It The dial (7) is used for both power (ON/OFF) and is also used for fader/balance controls when the volume control.
Page 173 Audio n Tone control To change control modes: Each brief press of the “ FAD/BAL” button (6) changes control modes in the The volume control dial (7) normally function as vol- following sequence starting from fader control ume control. The dial become a control for Bass or mode.
Page 174 Audio B Manual tuning (TUNE) n Seek tuning Turn the tuning knob (4) and hold it for more than a half second. Seek tuning will operate and stop auto- matically on the next station. Continue this operation until you find the desired station.
Page 175 Audio B How to preset stations 1. Press the “ FM/AM” selection button to select AM, FM1 or FM2 reception. 2. Press the “ SCAN” button (3) or tune the radio manually until the desired station frequency is dis- played. 3.
Page 176: Cassette Player Operation
Audio J Cassette player operation (9) Cassette slot (10) Eject button (11) Repeat button (12) TAPE (cassette player selection) button (13) TPS button (14) Dolby B NR button (15) Fast forward button (16) Program switching button (17) Rewind button HS5004CB –...
Page 177 Audio NOTE B Program switching button (PROG) D Only use good quality cassettes (cassettes When the program switching button “ PROG” (16) is longer than C-90 are not recommended). pressed during playback, the tape travel indicators D Put cassettes back in their boxes immediately will switch and the player will begin playing back the after use to protect them from dust and dirt and opposite side of the tape.
Page 178 Audio B Tape program sensor button (TPS) D When the blanks between selections are shorter than five seconds. n Blank skip D When there are no blanks between selections (live When the “ TPS” button (13) is pressed, the “ TPS” in- concerts, etc.).
Page 179: Built In Cd Changer Operation
Audio B Dolby B NR button ( Dolby Laboratories Licensing Corporation. “ Dolby” and the double-D Symbol are trade marks of Dolby Laboratories Li- Press “ ” button (14) when playing tapes re- censing Corporation. corded using the Dolby NR system*. The “ ”...
Page 180 Audio D The disc indicator steadily lights up if a disc is al- NOTE ready inserted in the corresponding position of the Make sure to always insert a disc with the label magazine. side up. If a disc is inserted with the label side D While the player is in the loading mode, if you down, it might be ejected or the player might press any of the other mode buttons “...
Page 181 Audio press any of the other mode buttons “ FM” (2), “ AM” When a CD is loaded, the player will start playback (1) and “ TAPE” (12), the player will enter standby of the CD, beginning with the first number. mode.
Page 182 Audio n Skipping forward To cancel the repeat mode, press the button again. Then the “ RPT” indicator goes out, and normal play- Turn the “ TRACK” knob (24) clockwise and release it back mode is restored. immediately to skip to the beginning of the next track.
Page 183 Audio whose “ DISC” indicator is ON. Precautions to observe when han- 2. Press the “ EJECT” button (22). Then the “ DISC” dling a compact disc (CD) indicator associated with the disc you have selected will blink, and the disc will be ejected. D To remove a disc from the case, press the center To remove more discs in succession, repeat Steps 1 of the case and hold both edges of the disc.
Page 184 Audio HG5009BA – CONTINUED – 5-27...
Page 186 Audio Antenna system ........FM reception .
Page 187 Audio Antenna system Installation of accessories Always consult your SUBARU dealer before instal- ling a citizen band radio or other transmitting device in your vehicle. Such devices may cause the elec- tronic control system to malfunction if they are incor- rectly installed or if they are not suited for the ve- hicle.
Page 188 Audio J Type B audio set Audio set Your SUBARU may be equipped with one of the fol- lowing audio sets. See the pages indicated in this section for operating details. J Type A audio set HS5004AA D Radio operation: refer to page 5-14...
Page 189 Audio Type A audio set (if equipped) The radio will operate only when the ignition switch is in the “ ACC” or “ ON” position. J Radio operation (1) SCAN button (2) Power switch, Volume control, Bass/Middle/Treble control and Fader/Balance control dial (3) Tuning buttons (4) FM/AM selection button (5) Preset buttons...
Page 190 Audio B Power switch and volume/bass/treble/fader/ To change control modes: Each brief press of the balance control (PWR/VOL) “ T/B” button changes control modes in the following sequence starting from volume control mode. (When The dial (2) is used for both power (ON/OFF) and the radio is first turned on, the control mode is in the volume control.
Page 191 Audio Display Control mode HB5036BA Turn counterclockwise Turn clockwise Bass control For less bass For more bass Treble control For less treble For more treble Balance con- To increase left speaker volume and decrease To increase right speaker volume and trol right speaker volume decrease left speaker volume...
Page 192 Audio from the low end to the high end. Press the “ SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “ SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low The display indicates which one is currently frequencies to high frequencies only.
Page 193 Audio NOTE preset buttons are cleared. If this occurs, it is necessary to reset the preset buttons. If the connection between the radio and battery is broken for any reason such as vehicle mainte- nance or radio removal, all stations stored in the J Compact disc player operation (7) Eject button (8) Disc slot...
Page 194 Audio B To play back a compact disc B To select a song from its beginning n When CD is not in the player n Forward direction ∧ Hold a disc with a finger in the center hole while Briefly press the “ ”...
Page 195 An optional CD changer can be connected to this B Random playback audio unit. See your SUBARU dealer for more information. Press the “ RPT/RDM” button (10) and hold it in for more than 2 seconds while a disc is being played back to play all songs on the disc in a random order.
Page 196 Audio (12) Track selection buttons (13) DISC button (14) Repeat/Randam button (15) Disc selection button HG5008DB – CONTINUED – 5-11...
Page 197 Audio B To start playback azines can also be selected in a similar way. When the “ CD” button (13) is pressed, the CD NOTE changer will start playback. The display shows the D No disc change takes place if the button corre- current disc number, track number and the elapsed sponding to the magazine slot in which no disc time during playback.
Page 198 Audio the CD changer will automatically stop fast forward- To cancel the random mode, press the button again. ing and start playback beginning with the first track Then the “ RDM” indicator goes out, and normal on the current disc. playback mode is restored.
Page 199 Audio Type B audio set (if equipped) The radio will operate only when the ignition switch is in the “ ACC” or “ ON” position. J Radio operation (1) FM button (2) AM button (3) SCAN button (4) Tuning knob (5) Preset buttons (6) Fader/Balance selection button (7) Power switch, Volume control,...
Page 200 Audio B Power switch and volume/bass/treble/fader/ This dial is used for bass/treble controls when the balance control (PWR/VOL) “ BAS/TRE” button (8) is in the depressed position. It The dial (7) is used for both power (ON/OFF) and is also used for fader/balance controls when the volume control.
Page 201 Audio n Tone control To change control modes: Each brief press of the “ FAD/BAL” button (6) changes control modes in the The volume control dial (7) normally function as vol- following sequence starting from fader control ume control. The dial become a control for Bass or mode.
Page 202 Audio B Manual tuning (TUNE) n Seek tuning Turn the tuning knob (4) and hold it for more than a half second. Seek tuning will operate and stop auto- matically on the next station. Continue this operation until you find the desired station.
Page 203 Audio B How to preset stations 1. Press the “ FM/AM” selection button to select AM, FM1 or FM2 reception. 2. Press the “ SCAN” button (3) or tune the radio manually until the desired station frequency is dis- played. 3.
Page 204 Audio J Cassette player operation (9) Cassette slot (10) Eject button (11) Repeat button (12) TAPE (cassette player selection) button (13) TPS button (14) Dolby B NR button (15) Fast forward button (16) Program switching button (17) Rewind button HS5004CB –...
Page 205 Audio NOTE B Program switching button (PROG) D Only use good quality cassettes (cassettes When the program switching button “ PROG” (16) is longer than C-90 are not recommended). pressed during playback, the tape travel indicators D Put cassettes back in their boxes immediately will switch and the player will begin playing back the after use to protect them from dust and dirt and opposite side of the tape.
Page 206 Audio B Tape program sensor button (TPS) D When the blanks between selections are shorter than five seconds. n Blank skip D When there are no blanks between selections (live When the “ TPS” button (13) is pressed, the “ TPS” in- concerts, etc.).
Page 207 Audio B Dolby B NR button ( Dolby Laboratories Licensing Corporation. “ Dolby” and the double-D Symbol are trade marks of Dolby Laboratories Li- Press “ ” button (14) when playing tapes re- censing Corporation. corded using the Dolby NR system*. The “ ”...
Page 208 Audio D The disc indicator steadily lights up if a disc is al- NOTE ready inserted in the corresponding position of the Make sure to always insert a disc with the label magazine. side up. If a disc is inserted with the label side D While the player is in the loading mode, if you down, it might be ejected or the player might press any of the other mode buttons “...
Page 209 Audio press any of the other mode buttons “ FM” (2), “ AM” When a CD is loaded, the player will start playback (1) and “ TAPE” (12), the player will enter standby of the CD, beginning with the first number. mode.
Page 210 Audio n Skipping forward To cancel the repeat mode, press the button again. Then the “ RPT” indicator goes out, and normal play- Turn the “ TRACK” knob (24) clockwise and release it back mode is restored. immediately to skip to the beginning of the next track.
Page 211 Audio whose “ DISC” indicator is ON. Precautions to observe when han- 2. Press the “ EJECT” button (22). Then the “ DISC” dling a compact disc (CD) indicator associated with the disc you have selected will blink, and the disc will be ejected. D To remove a disc from the case, press the center To remove more discs in succession, repeat Steps 1 of the case and hold both edges of the disc.
Page 212 Audio HG5009BA – CONTINUED – 5-27...
Page 214 Interior equipment Interior light ......... . . Dome light .
Page 215: Interior Equipment
Interior equipment J Luggage area light (if equipped) Interior light When leaving your vehicle, make sure the light is turned off to avoid battery discharge. The interior light switch has three positions: J Dome light HG0157 DOOR:The light comes on only when the rear gate is opened.
Page 216: Spotlight (If Equipped)
Interior equipment Spotlight (if equipped) Sun visors HB6006CA HB7001BA To turn on the spotlight, push the switch. To turn it To block out glare, swing down the visors. To use the off, push the switch again. sun visor at a side window, swing it down and move it sideways.
Page 217: Center Visor
Interior equipment J Center visor J Vanity mirror (if equipped) HG6002BA HB0137 To block out glare, swing down the visor. To use the vanity mirror, swing down the sun visor and open the vanity mirror cover.
Page 218: Storage Compartment
Interior equipment To open the glove compartment, pull the handle. To Storage compartment close it, push the lid firmly upward. To lock the glove compartment, insert the key and CAUTION turn it clockwise. D Always keep the storage compartment J Center console closed while driving to reduce the risk of inju- ry in the event of sudden stops or an accident.
Page 219: Cup Holder
Interior equipment J In center console (if equipped) Cup holder J In instrument panel HG1004CA The front passenger’s cup holder is built in the cen- HG6004BA ter console, beside the parking brake lever. To use the cup holder, push its front surface and pull CAUTION it out completely.
Page 220: Accessory Power Socket
Interior equipment might burn you or your passengers. Spilled Accessory power socket beverages may also damage upholstery, car- pets or audio equipment. J In the luggage compartment (if equipped) CAUTION D Do not attempt to use a cigarette lighter in the accessory power socket.
Page 221 If they do, do not use the electrical ap- to use only a SUBARU genuine cigarette pliance while driving. lighter plug. Do not use non-genuine cigarette lighter plugs or any “...
Page 222: Cigarette Lighter Socket (If Equipped)
To use the cigarette lighter, push in the knob and CAUTION wait a few moments. It will automatically spring up when ready for use. The electrical power socket located on the lower part of the instrument panel is designed to use only a SUBARU genuine cigarette – CONTINUED –...
Page 223: Ashtray
Interior equipment Ashtray WARNING To avoid being burned, never grasp the lighter Fully close the ashtray after using it to help reduce by the end with the heating element. Doing so residual smoke. could result in injury and could also damage the heating element.
Page 224: Floor Mat (If Equipped)
Interior equipment Floor mat (if equipped) CAUTION Make sure the driver’s floor mat is placed A retaining pin is located on the drivers side of the back in its proper location and correctly se- vehicle next to the fuel filler door release. cured on its retaining pin.
Page 225: Luggage Cover (If Equipped)
Interior equipment Luggage cover (if equipped) WARNING Do not place anything on the extended cover. The luggage cover is provided for covering the car- Putting excessive weight on the extended go area and to protect its contents from direct sun- cover can break it and an object on the cover light.
Page 226: To Install The Cover Housing
Interior equipment J To install the cover housing 1. Pull either sleeve on the end of the cover housing to shorten the cover’s length. HG6009BA 4. Store the cover housing under the luggage floor. HG6010BA 2. Insert the projections located on the both ends of the sleeve into the recesses of the retainers.
Page 227: Cargo Anchorage Eyelets (If Equipped)
Interior equipment Cargo anchorage eyelets CAUTION (if equipped) The cargo anchorage eyelets are designed only for securing light luggage. Never try to secure luggage that exceeds the capacity of the hooks. The maximum load capacity is 44 lb (20 kg) per an eyelet. HG6011BA The cargo area is equipped with four anchorage eyelets so that luggage can be secured with a lug-...
Page 228: Storage Tray (If Equipped)
Interior equipment Storage tray (if equipped) CAUTION D Always keep the lid of the storage tray closed while driving to reduce the risk of injury in the event of sudden stop or an acci- dent. D Do not store spray cans, containers with flammable or corrosive liquids or any other dangerous items in the storage tray.
Page 230 Starting and operating Fuel ABS system self-check 7-23 ................. ABS warning light 7-23 Fuel requirements...
Page 231: Starting And Operating
Starting and operating B Fuel octane rating Fuel This octane rating is the average of the Research Octane and Motor Octane numbers and is com- monly referred to as the Anti Knock Index (AKI). CAUTION Using a gasoline with a lower octane rating can Use of a fuel which is low in quality or use of cause persistent and heavy knocking, which can an inappropriate fuel additive may cause en-...
Page 232 (ethyl or grain alcohol) may be used in your vehicle, D Fuel system damage or driveability problems but should contain no more than 15% MTBE or 10% which result from the use of improper fuel are not ethanol for the proper operation of your SUBARU. – CONTINUED –...
Page 233: Fuel Filler Lid And Cap
Starting and operating covered under the SUBARU Limited Warranty. CAUTION Do not let fuel spill on the exterior surfaces of the vehicle. Fuels containing alcohol may cause paint damage, which is not covered un- der the SUBARU Limited Warranty. J Fuel filler lid and cap...
Page 234 3. Stop filling the tank after the fuel filler pump auto- covered under the SUBARU Limited Warranty. D Always use a genuine SUBARU fuel filler matically stops. Do not add any more fuel. 4. Put the cap back on, turn it clockwise until you cap.
Page 235: State Emission Testing (U.s. Only)
EXEMPTED At state inspection time, remember to tell your Subaru AWD vehicles from the portion of the testing inspection or service station in advance not to program that involves a two-wheel dynamometer. place your Subaru AWD vehicle on a two-wheel dynamometer.
Page 236: Preparing To Drive
CAUTION Resultant vehicle damage due to improper You should perform the following checks and adjust- testing is not covered under the SUBARU Lim- ments every day before you start driving. ited Warranty and is the responsibility of the 1. Check that all windows, mirrors, and lights are state inspection program or its contractors or clean and unobstructed.
Page 237: Starting The Engine
Starting and operating Starting the engine the key immediately after the engine has started. If the engine does not start within ten seconds, wait a while and then turn the ignition switch to the CAUTION “ START” position again while depressing the accel- erator pedal half way down.
Page 238: Starting A Flooded Engine
Starting and operating J Starting a flooded engine a while and then turn the ignition switch to the “ START” position again while depressing the accel- If the engine does not start, it may be flooded (ex- erator pedal half way down. cessive fuel in the engine).
Page 239: Stopping The Engine
Starting and operating Stopping the engine Manual transmission The ignition switch should be turned off only when The manual transmission is a fully synchromeshed the engine is idling. 5-forward and 1-reverse speed transmission. WARNING Do not stop the engine when the vehicle is moving.
Page 240: Shifting Speeds
Starting and operating WARNING Shift up mph (km/h) 1st to 2nd 15 (24) Do not drive the vehicle with the clutch disen- gaged (i.e., when clutch pedal 2nd to 3rd 25 (40) depressed) or with the shift lever in the neu- tral position.
Page 241: Driving Tips
Starting and operating 2.5 liter models (non-turbo) WARNING mph (km/h) When shifting down a gear, ensure that the TS, OUTBACK vehicle is not travelling at a speed exceeding 29 (46) 28 (45) the Maximum Allowable Speed for the gear which is about to be selected. Failure to 48 (77) 47 (75) observe this precaution can lead to engine...
Page 242: Automatic Transmission
Starting and operating labor. Automatic transmission On steep downgrades, downshift the transmission The automatic transmission is electronically con- to 4th, 3rd or 2nd gear as necessary; this helps to trolled with 4-forward speeds and 1-reverse speed. maintain a safe speed and to extend brake pad life. In this way, the engine provides a braking effect.
Page 243 Starting and operating J Selector lever for automatic transmis- CAUTION sion D Shift into the “ P” or “ R” position only after the vehicle is completely stopped. Shifting while the vehicle is moving may cause dam- age to the transmission. D Do not race the engine for more than five seconds in any position except the “...
Page 244 Starting and operating ic transmission system to ensure safe starting of the vehicle. To shift the selector lever from the “ P” to the any oth- er position, you have to depress the brake pedal ful- ly when the ignition switch is in the “ ON” position. This prevents the vehicle from lurching when it is started.
Page 245 Starting and operating of the vehicle. WARNING NOTE Do not drive the vehicle with the selector lever The transmission may downshift to 2nd or 1st in the “ N” (neutral) position. Engine braking gear, depending on the way the accelerator pedal has no effect in this condition and the risk of is pressed to accelerate the vehicle again.
Page 246 Starting and operating B 3 (Third) B Maximum speeds This position is for using engine braking when going The following tables show the maximum speeds that down a hill or for climbing a grade. are possible with each different gear. The tachome- The transmission automatically shifts into a suitable ter’s needle will enter the red area if these speeds gear from 1st to 3rd according to the vehicle speed...
Page 247: Shift Lock Release
Starting and operating B Driving tips imum Allowable Speed for the current gear is exceeded. D Always apply the foot or parking brake when the D Similarly, in order to prevent over-revving dur- vehicle is stopped in the “ D” , “ 3” , “ 2” , “ 1” or “ R” ing deceleration of the vehicle, the transmission position.
Page 248 Starting and operating 6. Remove the screwdriver from the hole. Depress the brake pedal and start the engine. Take your vehicle to the nearest SUBARU dealer im- mediately to have the system repaired. HB7010CA HG7010BA 4. Insert the screwdriver into the hole.
Page 249: Rear Viscous Limited Slip Differential (Lsd) (If Equipped)
Starting and operating Rear viscous limited slip differential Power steering (LSD) (if equipped) The power steering system operates only when the engine is running. The LSD provides optimum distribution of power ac- If you lose power steering assist because the en- cording to the difference in revolutions between the gine stops or the system fails to function, you can right and left rear wheels that may be caused by...
Page 250: Braking
Starting and operating B Braking when a tire is punctured Braking Do not depress the brake pedal suddenly when a J Braking tips tire is punctured. This could cause a loss of control of the vehicle. Keep driving straight ahead while gradually reducing speed.
Page 251: Abs (Anti-Lock Brake System)
ABS equipped vehicle could easily lead to a disc brakes give a warning noise when the brake serious accident. pads are worn. If a squeaking or scraping noise is heard from the disc brakes while braking, immediately have your vehicle checked by your SUBARU dealer. 7-22...
Page 252: Abs Warning Light
Starting and operating J ABS warning light CAUTION D The ABS system does not always decrease stopping distance. You should always main- tain a safe following distance from other ve- hicles. D When driving on badly surfaced roads, grav- el roads, icy roads, or over deep newly fallen snow, stopping distances may be longer for a vehicle with the ABS system than one without.
Page 253 D The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer. NOTE If the warning light behavior is as described below, the ABS system may be considered nor- mal.
Page 254: Parking Your Vehicle
Starting and operating Parking your vehicle CAUTION Never drive while the parking brake is set be- cause this will cause unnecessary wear on the WARNING brake linings. Before starting to drive, always D Never leave unattended children or pets in make sure that the parking brake has been ful- ly released.
Page 255 Starting and operating running, the parking brake warning light comes on. front wheels should be turned away from the curb. After starting the vehicle, be sure that the warning light has gone out before the vehicle is driven. Refer to the “ Warning and indicator lights” section (chap- ter 3).
Page 256: Cruise Control (If Equipped)
Starting and operating J To set cruise control Cruise control (if equipped) Cruise control enables you to maintain a constant vehicle speed without holding your foot on the ac- celerator pedal and it is operative when the vehicle speed is 25 mph (40 km/h) or more. Make sure the main switch is turned “...
Page 257: To Turn Off The Cruise Control
Starting and operating porarily: D Depress the brake pedal. D Pull the control lever in the “ CANCEL” direction. (if so equipped) D Depress the clutch pedal (manual transmission vehicles only). D Shift the selector lever into the “ N” position (auto- matic transmission vehicles only).
Page 258 Starting and operating B To decrease the speed the desired speed. 1. Push the control lever downward in the “ SET, When the difference between the actual vehicle COAST” direction and hold it until the vehicle reach- speed and the set speed is less than 4 mph (6.8 es the desired speed.
Page 260 Driving tips New vehicle break-in driving – Warranties and maintenance 8-27 ....Maximum load limits 8-27 the first 1,000 miles (1,600 km) .
Page 261: Driving Tips
Driving tips New vehicle break-in driving – Fuel economy hints the first 1,000 miles (1,600 km) The following suggestions will help to save your fuel. D Select the proper gear position for the speed and The performance and long life of your vehicle are dependent on how you handle and care for your ve- road conditions.
Page 262: Engine Exhaust Gas (Carbon Monoxide)
Driving tips Engine exhaust gas sible. If you must drive under these condi- tions, drive only with all windows fully open. (Carbon monoxide) D Keep the trunk lid or rear gate closed while driving to prevent exhaust gas from entering the vehicle.
Page 263: Catalytic Converter
Driving tips Catalytic converter HB3003BA Non-turbo models HG8000BA The catalytic converter is installed in the exhaust Turbo models system. It serves as catalyst to reduce HC, CO and NOx in exhaust gases, thus providing cleaner ex- haust. To avoid damage to the catalytic converter: D Use only unleaded fuel.
Page 264: Periodic Inspections
(misfiring, backfiring or incomplete Periodic inspections combustion), have your vehicle checked and re- paired by an authorized SUBARU dealer. To keep your vehicle in the best condition at all D Do not apply undercoating or rust prevention times, always have the recommended maintenance...
Page 265: Driving In Foreign Countries
By shifting power between the front and rear wheels, SUBARU AWD can also provide added traction dur- ing acceleration and added engine braking force during deceleration.
Page 266 Driving tips D Tire chains should always be placed on the front AWD system, you should keep the following tips in mind: wheels only. D There are some precautions that you must ob- D An AWD vehicle is better able to climb steeper serve when towing your vehicle.
Page 267: Off Road Driving
J All AWD models except OUTBACK roads or off-road. But please keep in mind that an SPORT AWD SUBARU is a passenger car and is neither a Your AWD vehicle is neither a conventional off-road conventional off-road vehicle nor an all-terrain ve- vehicle nor an all terrain vehicle.
Page 268 Driving tips aid kit and portable phone or citizens band radio. may cause it to stall. Never attempt to drive through D Drive carefully. Do not take unnecessary risks by rushing water; regardless of its depth, it can wash driving in dangerous areas or over rough terrain. away the ground from under your tires, resulting in D Slow down and employ extra caution at all times.
Page 269: Winter Driving
Maintenance Booklet” . small shovel, and jumper cables. Remember that damage done to your Subaru while Check the battery and cables. Cold temperatures operating it off-road and not using common sense reduce battery capacity.
Page 270 Driving tips B Parking in cold weather Keep the door locks from freezing by squirting them with deicer or glycerin. Do not use the parking brake when parking for long periods in cold weather since it could freeze in that Forcing a frozen door open may damage or sepa- position.
Page 271: Driving On Snowy And Icy Roads
The optional 17-inch tires for the WRX are sum- mer tires. Compared with winter and all-season If your SUBARU is not going to be used for an ex- tires, summer tires give significantly less grip on tended period, it is best to have the fuel tank filled to snowy and icy road surfaces.
Page 272: Corrosion Protection
Driving tips from working effectively. If snow is stuck on the WARNING wiper arm, pull off the road to a safe place, then remove it. If you stop the car at road side, use the Do not use the cruise control on slippery hazard warning flasher to alert other drivers.
Page 273: Tire Chains
Driving tips gerous and lead to loss of vehicle control. When you choose to install winter tires on your ve- D You must install four winter tires that are of hicle, be sure to use the correct tire size and type. the same size, construction, brand, and load You must install four winter tires that are of the same range.
Page 274: Loading Your Vehicle
Driving tips chains — overconfidence because you are driving Loading your vehicle with tire chains could easily lead to a serious acci- dent. WARNING CAUTION D Never allow passengers to ride on the Tire chains cannot be fitted with optional folded rear seatback, in the trunk or in the car- 215/45 R17 tires for the WRX because of lack go area.
Page 275: Vehicle Capacity Weight
Driving tips WARNING CAUTION D When you carry something inside the ve- Do not carry spray cans, containers with flam- hicle, secure it whenever you can to prevent it mable or corrosive liquids or any other dan- from being thrown around inside the vehicle gerous items inside the vehicle.
Page 276 Driving tips J GVWR and GAWR (Gross Vehicle Weight Rating and Gross Axle Weight Rating) HB0382 The load capacity of your vehicle is determined by weight, not by available cargo space. The maximum load you can carry in your vehicle is shown as the HGS028CA Vehicle Capacity Weight on the tire information label attached to the driver’s side door jamb.
Page 277: Roof Rail And Crossbar (If Equipped)
Driving tips J Roof rail and crossbar (if equipped) bly) plus the vehicle capacity weight. In addition, the total weight applied to each axle (GAW) must never exceed the GAWR. The front and rear GAWs can be adjusted by relocating luggage inside the vehicle.
Page 278 Driving tips ter for information on loading cargo into or onto your etc. on the crossbars, follow the manufacturer’s vehicle. The maximum load limit of the cargo, cross- instructions and make sure that the attachment is bars and carrying attachment must not exceed 100 securely fixed to the crossbars.
Page 279 Driving tips n To install the crossbar Front crossbar: Front crossbar has 100 LBS. Load Label on left- hand side. HG8010BB 8-20...
Page 280 Driving tips F) Front of vehicle NOTE 1) T30 torxR head screw It may be necessary to squeeze the lower clamp 2) Front arrow label and the end support together to compress the 3) Front crossbar pads and gain a better alignment of the pieces 4) 100LBS load label while trying to start the screw.
Page 281 Driving tips Rear crossbar: F) Front of vehicle 1) T30 torxR head screw 2) Front arrow label 3) Rear crossbar 4) 0 inch (0 mm) 5) Roof rail end support 6) Joint line 7) Front arrow label Install the rear crossbar in the same manner as the front crossbar.
Page 282 Driving tips checked, and retightened if necessary to 35 inch Trailer hitch (if equipped) lbs. (4.0 N-m, 0.41 kg-m), as outlined in Step #5 above. The trailer hitch is designed to tow a Class 1 rated load. A maximum of 2,000 lbs. (906 kg) gross trailer weight and a maximum of 200 lbs.
Page 283: Connecting A Trailer
Driving tips for positive locking placement before towing a trailer. If the ball mount comes off the hitch re- ceiver, the trailer could get loose and create a traffic safety hazard. D Use only the ball mount supplied with this hitch.
Page 284 Driving tips 4. Pull the ball mount to make sure it does not come off the hitch receiver. HB8020BC 1) Hitch ball installation point HB8020AA 2) Hooks for safety chains 5. Use only a hitch ball that is appropriate for the ball mount and your trailer.
Page 285 Driving tips 9. Confirm proper function of the hitch wire harness by individually activating the brake, right turn signal, left turn signal, stop, and parking lights on the trailer. NOTE Always disconnect the trailer wire harness be- fore launching or retrieving a watercraft. J When you do not tow a trailer D Remove the ball mount from the hitch receiver tube and insert the receiver cover onto the hitch re-...
Page 286: Trailer Towing
J Maximum load limits ment and cautious operation of your vehicle. Seek the advice of your SUBARU dealer to assist you in WARNING purchasing a hitch and other necessary towing equipment appropriate for your vehicle. In addition,...
Page 287 Driving tips B Total trailer weight The total trailer weight (trailer weight plus its cargo load) must never exceed the maximum weight shown below. Model Conditions Maximum total trailer weight MT models When towing a trailer with- 1,000 lbs out brakes. (453 kg) OM-H2781 When towing a trailer with...
Page 288 Driving tips B Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR) The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehicle.
Page 289 Driving tips towing coupler at the height at which it would be during actual towing, using a jack as shown. HGS028CA Certification label OM-H2785 To check both GVWR and GAWR and to confirm that Tongue load the total weight and weight distribution are within safe driving limits, you should have your vehicle and trailer weighed at a commercial weighing station.
Page 290 Driving tips HG8009BB OM-H2787 1) Jack F) Front of vehicle 2) Bathroom scale The tongue load can be adjusted by proper distribu- WARNING tion of the load in the trailer. Never load the trailer If the trailer is loaded with more weight in the with more weight in the back than in the front;...
Page 291: Trailer Hitches
Driving tips J Trailer hitches B WAGON including OUTBACK SPORT The use of a genuine SUBARU trailer hitch is recom- Choose a proper hitch for your vehicle and trailer. mended. A genuine SUBARU hitch is available from your SUBARU dealer.
Page 292 Your hitch ball. Allow sufficient slack in the chains taking SUBARU’s brake system is not designed to be tight-turn situations into account; however, be care- tapped into the trailer’s hydraulic brake system.
Page 293 If you carry a regular size spare tire in your vehicle date wiring changes. To ensure the trailer lights are or trailer as a precaution against getting a flat tire, connected properly, please consult your SUBARU be sure that the spare tire is firmly secured. 8-34...
Page 294: Trailer Towing Tips
Driving tips apparent, do not tow the trailer. WARNING D Check that the vehicle sits horizontally with the trailer attached. If the vehicle is tipped sharply up at Never tow a trailer when the temporary spare the front and down at the rear, check the total trailer tire is used.
Page 295 SUBARU dealer. D When passing other vehicles, considerable dis- B Driving on grades tance is required because of the added weight and...
Page 296 Driving tips sudden downshifts. You should not park on a hill or slope. But if parking D When driving uphill in hot weather, the air condi- on a hill or slope cannot be avoided, you should tioner may turn off automatically to protect the take the following steps: engine from overheating.
Page 298 In case of emergency If you park your vehicle in case of an emergency ........Temporary spare tire (if equipped) .
Page 299: In Case Of Emergency
In case of emergency If you park your vehicle in case of an NOTE When the hazard warning flasher is on, the turn emergency signals do not work. HG3004AA The hazard warning flasher should be used in day or night to warn other drivers when you have to park your vehicle under emergency conditions.
Page 300: Temporary Spare Tire (If Equipped)
In case of emergency D Do not exceed 50 mph (80 km/h). Temporary spare tire (if equipped) D Do not put a tire chain on the temporary spare tire. Because of the smaller tire size, a tire chain will not fit properly.
Page 301 In case of emergency CAUTION Never use any temporary spare tire other than the original. Using other sizes may result in severe mechanical damage to the drive train of your vehicle. HB8003BC 1) Spare fuse 2) FWD connector NOTE (If your vehicle is AWD with automatic transmis- sion, except Turbo models) Before driving your vehicle with the temporary spare tire, put a spare fuse inside the FWD connector in the main fuse...
Page 302: Flat Tires
In case of emergency Flat tires 1. Park on a hard, level surface, whenever possible, then stop the engine. 2. Set the parking brake securely and shift a manual If you have a flat tire while driving, never brake sud- transmission vehicle in reverse or an automatic denly;...
Page 303 In case of emergency HGF014BB HGF020BB Sedan Wagon 1) Jack 3) Spare tire 1) Jack 3) Spare tire 2) Jack handle 2) Jack handle 5. Take out the spare tire, jack, and wheel nut wrench. The spare tire is stored under the floor of the trunk or cargo area.
Page 304 In case of emergency HGS039BA Sedan: Remove the floor cover from the trunk. Re- move the storage tray (if so equipped). Turn the attaching bolt counterclockwise, then take the spare tire out. HGS040BA – CONTINUED –...
Page 305 In case of emergency Wagon: Open the lid and hang the hook provided To take out the jack: on the under side of the lid on the rear edge of the Remove the cover, turn the jackscrew counterclock- roof to keep the lid open. wise to loosen it, then remove the jack.
Page 306 In case of emergency OM-H0376 HGS044BA 7. Loosen the wheel nuts using the wheel nut Others wrench but do not remove the nuts. 8. Place the jack under the side sill at the front or rear jack-up point closest to the flat tire. Turn the jackscrew by hand until the jack head en- gages firmly into the jack-up point.
Page 307 In case of emergency OM-H2263 HG0104 9. Insert the jack handle into the jackscrew, and 11. Before putting the spare tire on, clean the turn the handle until the tire clears the ground. Do mounting surface of the wheel and hub with a cloth. not raise the vehicle higher than necessary.
Page 308 In case of emergency OM-H0377 HGS045BA 14. Use the wheel nut wrench to securely tighten 15. Store the flat tire in the spare tire compartment. the wheel nuts to the specified torque, following the Put the spacer and tighten the attaching bolt firmly. tightening order in the illustration.
Page 309: Jump Starting
In case of emergency D Be sure the jumper cables and clamps on Jump starting them do not have loose or missing insulation. Do not jump start unless cables in suitable condition are available. WARNING D A running engine can be dangerous. Keep D Battery fluid is SULFURIC ACID.
Page 310 In case of emergency 1) Booster battery 2) Engine lifting bracket HB8007BC – CONTINUED – 9-13...
Page 311: Engine Overheating
In case of emergency (1) Connect one jumper cable to the positive (+) Engine overheating terminal on the discharged battery. (2) Connect the other end of the jumper cable to the positive (+) terminal of the booster battery. WARNING (3) Connect one end of the other cable to the negative (–...
Page 312: Towing
If towing is necessary, it is best done by your 3. After engine coolant temperature SUBARU dealer or a commercial towing service. dropped, turn off the engine. Observe the following procedures for safety. If the temperature gauge stays at the overheated zone, turn the engine off.
Page 313: Towing And Tie-Down Eyes
In case of emergency operation or deterioration of the center differ- Front towing eye: ential. J Towing and tie-down eyes The towing eyes should be used only in an emer- gency (e.g., to free a stuck vehicle from mud, sand or snow).
Page 314 In case of emergency 1. Take out the towing eye, screwdriver and wheel Rear towing eye: nut wrench from the on board tool bag. 2. Pry off the cover on the front bumper using a screwdriver, and you will find a threaded hole for at- taching the towing eye.
Page 315: Using A Flat-Bed Truck
In case of emergency Tie-down eyes: CAUTION Never use the tie-down eye on the underside of the vehicle closest to the muffler for towing purposes. J Using a flat-bed truck HG9002AA This is the best way to transport your vehicle. Use the following procedures to ensure safe transporta- tion.
Page 316: Towing With All Wheels On The Ground
In case of emergency 3. Secure the vehicle onto the carrier properly with 1. Check the transmission and differential oil levels safety chains. Each of safety chain should be and add oil to bring it to the upper level if necessary. equally tightened and care must be taken not to pull 2.
Page 317: Maintenance Tools
In case of emergency Maintenance tools CAUTION D If transmission failure occurs, transport your vehicle on a flat-bed truck. D Do not run the engine while being towed in this method. Transmission damage could re- sult if the vehicle is towed with engine run- ning.
Page 318: J Jack And Jack Handle
In case of emergency J Jack and jack handle HGF014BB Sedan HGS042BA 1) Jack 3) Spare tire The jack is stored on the left side of the trunk or 2) Jack handle cargo area. To take out the jack, turn the jackscrew counter- clockwise to loosen it, then remove the jack.
Page 319 In case of emergency HGF020BB Wagon 1) Jack 3) Spare tire 2) Jack handle The jack handle is stored under the spare tire cover. For how to use the jack, refer to “ Flat tires” . 9-22...
Page 320: Appearance Care
Appearance care Exterior care 10-2 ......... . Washing 10-2 .
Page 321: Appearance Care
Appearance care Exterior care CAUTION D When washing the vehicle, the brakes may J Washing get wet. As a result, the brake stopping dis- The best way to preserve your vehicle’s beauty is tance will be longer. To dry the brakes, drive frequent washing.
Page 322: Waxing And Polishing
J Waxing and polishing undercoat. When in doubt, it is always best to con- tact your SUBARU dealer or an auto paint specialist. Always wash and dry the vehicle before waxing and polishing.
Page 323: To Help Prevent Corrosion
4. High temperatures will cause corrosion to parts of the vehicle which cannot dry quickly due to lack of proper ventilation. Your SUBARU has been designed and built to resist corrosion. Special materials and protective finishes J To help prevent corrosion...
Page 324: Cleaning The Interior
Use the cleaner according to its instructions. J Leather seat materials The leather used by SUBARU is a high quality natu- ral product which will retain its distinctive appear- ance and feel for many years with proper care.
Page 325: Synthetic Leather Upholstery
If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage.
Page 326: Maintenance And Service
Maintenance and service Maintenance schedule 11-3 Checking the oil level 11-26 ......
Page 327 Maintenance and service Wheel balance 11-41 ........Wear indicators 11-41 .
Page 328: Maintenance Schedule
“ Warranty and Maintenance Booklet” . you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU. Incorrect or incomplete service could cause improper or unsafe vehicle operation. Any problems caused by improper maintenance and service per- formed by you are not eligible for warranty cover- age.
Page 329 If your SRS airbag or seatbelt pretensioner D Always use the proper tools and make cer- needs service, consult your nearest SUBARU tain that they are well maintained. dealer. D Never get under the vehicle supported only by a jack.
Page 330: Engine Hood
Maintenance and service “ ON” position, the cooling fan may operate Engine hood suddenly even when the engine is stopped. To open the hood: J When you do checking or servicing in the engine compartment while the engine is running A running engine can be dangerous.
Page 331 Maintenance and service Lift up the hood, release the hood prop from its retainer and put the end of the hood prop into the slot in the hood. To close the hood: 1. Lift the hood slightly and remove the hood prop from the slot in the hood and return the prop to its retainer.
Page 332: Engine Compartment Overview
Maintenance and service Engine compartment overview J 2.5 liter model 1) Manual transmission oil level gauge (MT) (page 11-23) or Differential gear oil level gauge (AT) (page 11-26) 2) Air cleaner element (page 11-18) 3) Clutch fluid reservoir (page 11-31) 4) Automatic transmission fluid level gauge (page 11-24) 5) Brake fluid reservoir (page 11-30)
Page 333 Maintenance and service J 2.0 liter (Turbo) model Manual transmission oil level gauge (MT) (page 11-23) Air cleaner element (page 11-18) Clutch fluid reservoir (page 11-31) Brake fluid reservoir (page 11-30) Windshield washer tank (page 11-46) Fuse box (page 11-51) Battery (page 11-50) Engine oil filler cap (page 11-9)
Page 334: Engine Oil
Maintenance and service Engine oil J Checking the oil level Check the engine oil level at each fuel stop. 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the dipstick, wipe it clean, and insert it again.
Page 335: Changing The Oil And Oil Filter
Maintenance and service engine oil level reading may be in a range between the upper level and the notch mark. This is caused by thermal expansion of the engine oil. To prevent overfilling the engine oil, do not add any additional oil above the upper level when the engine is cold.
Page 336 Maintenance and service 5. Wipe the seating surface of the drain plug with a CAUTION clean cloth and tighten it securely with a new seal- ing washer after the oil has completely drained out. Never over tighten the oil filter because that can result in an oil leak.
Page 337 HGB018BB gether as long as they are the same API classifica- tion and SAE viscosity as those recommended by API Service label SUBARU. 1) Indicates the oil quality by API designa- tions Engine oil viscosity (thickness) affects fuel economy. 2) Indicates the SAE oil viscosity grade Oils of lower viscosity provide better fuel economy.
Page 338: Cooling System
– 33°F (– 36°C). For adding, use genuine SUBARU If the vehicle is used in desert areas, in areas with coolant or an equivalent: a mixture of 50%...
Page 339: Engine Coolant
Check the fuse and re- place it if necessary. If the fuse is not blown, have the cooling system checked by your SUBARU deal- HGB001CB 1) “FULL” level mark If frequent addition of coolant is necessary, there 2) “LOW”...
Page 340 Maintenance and service HG0115 HGA000BD 1) Rubber gaskets 1) Drain plug 3. After refilling the reserve tank and the radiator, re- 3. Loosen the radiator cap to drain the coolant from install the caps and check that the rubber gaskets the radiator.
Page 341 Maintenance and service HBB007BC HG0163 Non-turbo models Turbo models 1) Filler neck 1) Filler neck 2) Fill up to this level 2) Fill up to this level 11-16...
Page 342 Maintenance and service to insufficient air bleeding and trapped air in the system. Coolant capacity: Non-turbo models: MT. 7.4 US qt (7.0 liters, 6.2 Imp qt) AT. 7.3 US qt (6.9 liters, 6.1 Imp qt) Turbo models: MT. 8.1 US qt (7.7 liters, 6.8 Imp qt) AT.
Page 343: Air Cleaner Element
B Non-turbo models Replace the air cleaner element according to the maintenance schedule in the “ Warranty and Mainte- nance Booklet” . Under extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts. 11-18...
Page 344 Maintenance and service HBA002BC HBA003BC 1) Bolt 1) Air cleaner element 1. Remove the bolt securing the rear air cleaner ele- 3. Separate the rear air cleaner element case from ment case. the front cleaner element case and remove the air 2.
Page 345 Maintenance and service B Turbo models 1. Unsnap the two clamps holding the air cleaner case cover. 2. Open the air cleaner case cover and remove the air cleaner element. 3. Clean the inside of the air cleaner cover and case with a damp cloth and install a new air cleaner element.
Page 346: Spark Plugs
PFR6G (NGK) correct order. HBA004BA It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs re- placed by your SUBARU dealer. The spark plugs should be replaced according to – CONTINUED – 11-21...
Page 347: Drive Belts
(98 N, 10 kg) midway between the pulleys by us- ing a spring scale. Belt deflection should be the amount specified. If a belt is loose, cracked, or worn, contact your SUBARU dealer. HGA005BC 1) Power steering pump pulley...
Page 348: Manual Transmission Oil
Maintenance and service Manual transmission oil J Checking the oil level Check the oil level monthly. 1. Park the vehicle on a level surface and stop the engine. HGB001JA Turbo model HGB001DB Non-turbo model 1) Yellow handle HGB034BB 1) Upper level 2) Lower level –...
Page 349: Automatic Transmission Fluid
Maintenance and service 2. Pull out the dipstick, wipe it clean, and insert it Automatic transmission fluid again. 3. Pull out the dipstick again and check the oil level J Checking the fluid level on it. If it is below the lower level, add oil through the The automatic transmission fluid expands largely as dipstick hole to bring the level up to the upper level.
Page 350: Recommended Fluid
Maintenance and service 4. Pull out the dipstick and check the fluid level on the gauge. If it is below the lower level on the “ HOT” range, add the recommended automatic transmis- sion fluid up to the upper level. B Checking the fluid level when the fluid is cold When the fluid level has to be checked without time to warm up the automatic transmission, check to...
Page 351: Front Differential Gear Oil (At Vehicles)
Maintenance and service Front differential gear oil (AT vehicles) J Checking the oil level Check the differential oil level monthly. HBA010BC 1) Upper level 2) Lower level 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the dipstick, wipe it clean, and insert it again.
Page 352: Rear Differential Gear Oil
Maintenance and service Rear differential gear oil J Checking the gear oil level Your vehicle may be equipped with a rear differential protector. The differential protector provides protec- tion to the rear differential assembly during off-road use. Removal of the rear differential protector is not required when checking the oil level.
Page 353 SAE viscosity No. and Applicable Tem- perature CAUTION If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. 11-28...
Page 354: Power Steering Fluid
Maintenance and service Power steering fluid J Checking the fluid level The power steering fluid expands greatly as its tem- perature rises; the fluid level differs according to fluid temperature. Therefore, the reservoir tank has two different checking ranges for hot and cold fluids.
Page 355: Recommended Fluid
Maintenance and service If the fluid level is extreme low, it may indicate pos- Brake fluid sible leakage. Consult your SUBARU dealer for in- spection. J Checking the fluid level Check the fluid level monthly. WARNING Be careful not to burn yourself because the fluid may be hot.
Page 356: Checking The Fluid Level
D If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. CAUTION D Never use different brands of brake fluid to- gether.
Page 357: Recommended Clutch Fluid
D Clutch fluid absorbs moisture from the air. Any absorbed moisture can cause improper clutch operation. D If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU 11-32...
Page 358: Brake Booster
If the brake booster does not operate as described Check the brake pedal free play and reserve dis- below, have it checked by your SUBARU dealer. tance according to the maintenance schedule in the 1. With the engine off, depress the brake pedal sev- “...
Page 359: Checking The Clutch Function
(294 N, 30 kg) and measure the distance be- tween the upper surface of the pedal pad and the floor. When the measurement is smaller than the specifi- cation, or when the pedal does not operate smooth- ly, contact with your SUBARU dealer. 11-34...
Page 360: Replacement Of Brake Pad And Lining
SUBARU dealer. noise when the brake pedal is applied. If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible. – CONTINUED – 11-35...
Page 361 7 – 8 notches / 44 lb (196 N, 20 kg) linings When replacing the brake pad or lining, use only WARNING genuine SUBARU parts. After replacement, the new parts must be broken in as follows: A safe location and situation should be se- B Brake pad and lining lected for break-in driving.
Page 362: Parking Brake Stroke
(snow) tires. SUBARU dealer. When installing winter tires, be sure to replace all four tires. B Winter (snow) tires Winter tires are best suited for driving on snow-cov- –...
Page 363: Tire Inspection
Check and, if necessary, ad- time, check the tires for abnormal wear. just the pressure of each tire (including the spare) at Contact your SUBARU dealer immediately if you find least once a month (for example, during a fuel stop) any problem.
Page 364 Maintenance and service D Correct tire pressure (tread worn evenly) Driving even a short distance warms up the tires and increases the tire pressures. Also, the tire pres- sures are affected by the ambient temperature. It is best to check tire pressure outdoors before driving the vehicle.
Page 365 Maintenance and service D Abnormally low tire pressure (tread worn at D Abnormally high tire pressure (tread worn in shoulders) center) HGB024AA HGB025AA Rolling resistance is high, so fuel consumption is Ride comfort is poor. Also, the tire magnifies the also higher.
Page 366: Wear Indicators
If you suspect that the wheels are not correctly balanced, have them checked and ad- justed by your SUBARU dealer. Also have them ad- justed after tire repairs and after tire rotation. NOTE...
Page 367: Tire Rotation
Maintenance and service J Tire rotation WARNING When a tire’s tread wear indicator becomes visible, the tire is worn beyond the acceptable limit and must be replaced immediately. With a tire in this condition, driving at high speeds in wet weather can cause the vehicle to hydro- plane.
Page 368: Tire Replacement
Maintenance and service check the wheel nuts again and retighten any nut For safe vehicle operation, SUBARU recommends that has become loose. replacing all four tires at the same time. J Tire replacement NOTE Unidirectional tires: Some tires have a specified The wheels and tires are important and integral direction of rotation.
Page 369: Wheel Replacement
Replacement wheels are available from SUBARU dealers. WARNING Use only those wheels that are specified for your vehicle. Wheels not meeting specifica-...
Page 370: Aluminum Wheels (If Equipped)
SUBARU parts designed for aluminum wheels. check the tightness of the wheel nuts after driv- ing approximately 600 miles (1,000 km). If any nut is loose, tighten it to the specified torque.
Page 371: Windshield Washer Fluid
Use windshield washer fluid. If windshield washer fluid is unavailable use clean water. In areas where water freezes in winter, use an anti- freeze type windshield washer fluid. SUBARU Wind- shield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated below.
Page 372: Replacement Of Windshield Wiper Blades
Maintenance and service Replacement of windshield wiper blades Grease, wax, insects, or other material on the wind- shield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield (or rear window) and the wiper blades using a sponge or soft cloth with a...
Page 373 Maintenance and service HS0191 HS0192 1) Metal support 1) Metal spines 3. Grasp the locked end of the blade rubber as- 4. If the new blade rubber is not provided with two sembly and pull it firmly until the stoppers on the metal spines, remove the metal spines from the old rubber are free of the metal support.
Page 374 Maintenance and service HS0193 HS0194 5. Align the claws of the metal support with the 1) Stopper grooves in the rubber and slide the blade rubber as- Be sure to position the claws at the end of the metal sembly into the metal support until it locks. support between the stoppers on the rubber as shown.
Page 375: Battery
Maintenance and service Battery because a short circuit will result. D Keep everyone including children away from the battery. D Charge the battery in a well-ventilated area. WARNING D Battery posts, terminals and related acces- D Before beginning work on or near any bat- sories contain lead and lead compounds, chemicals known to the State of California to tery, be sure to extinguish all cigarettes,...
Page 376: Fuses
Maintenance and service Fuses CAUTION Never replace a fuse with one having a higher rating or with material other than a fuse be- cause serious damage or a fire could result. The fuses are designed to melt during an overload to prevent damage to the wiring harness and electri- OM-H1048 cal equipment.
Page 377 Maintenance and service main fuse box cover in the engine compartment. If any lights, accessories or other electrical controls do not operate, inspect the corresponding fuse. If a fuse has blown, replace it. HB8003CA The other one is housed in the engine compartment. HS0204 A) Good B) Blown...
Page 378: Main Fuse
The main fuses are designed to melt during an over- 6. If the same fuse blows again, this indicates that load to prevent damage to the wiring harness and its system has a problem. Contact your SUBARU electrical equipment. Check the main fuses if any dealer for repairs.
Page 379: Installation Of Accessories
Maintenance and service Installation of accessories Always consult your SUBARU dealer before instal- ling fog lights or any other electrical equipment in your vehicle. Such accessories may cause the elec- tronic system to malfunction if they are incorrectly installed or if they are not suited for the vehicle.
Page 380: Replacing Bulbs
Maintenance and service Replacing bulbs HGF027BB – CONTINUED – 11-55...
Page 381: Headlight
High mount stop light NOTE Sedan (in compartment) 12V-18W If headlight aiming is required, consult your Sedan (in rear spoiler) 12V-1.2W — SUBARU dealer for proper adjustment of the Wagon 12V-13W headlight aim. 10) Backup light 12V– 21W 7440 11) Rear turn signal 12V–...
Page 382 Maintenance and service 2. Remove the bulb holder from the headlight as- sembly by turning it counterclockwise. HGB021BB 1) Push 2) Pull HGB023BA 1. Disconnect the electrical connector while press- 3. Remove the bulb from the headlight assembly. ing the lock release tab. 4.
Page 383 When the headlight assembly has been removed and then re- installed, it may become necessary to make a head- light aiming adjustment. It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary. 11-58...
Page 384 Maintenance and service 1. Remove the front grille. Use a screwdriver to de- tach the four clips at the top and the two hooks on each side. HGB028BA 2. Loosen three clips to remove the headlight side cover. HGB027BA f : Clip j : Hook HGB029BA –...
Page 385 Maintenance and service 3. Remove three bolts and disconnect connectors, 4. Remove the bulb socket from the headlight as- and then detach headlight assembly. sembly by turning it counterclockwise. HGB030BA HGB010BA 5. Pull the bulb out of the socket. Install a new bulb. 6.
Page 386: Front Fog Light (If Equipped)
Maintenance and service J Front fog light (if equipped) 2. Disconnect the connector. CAUTION Halogen fog light bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, finger prints or grease on the bulb surface develop into hot spots, causing the bulb to break.
Page 387: Front Side Marker Light
Maintenance and service J Front side marker light OM-H0412 1) Spring HGB020BA 2) Connector 1. Remove the front side marker light assembly by 4. Disconnect the connector behind the case cap. prying the edge of the lens with a regular screwdriv- 5.
Page 388: Rear Combination Lights
Maintenance and service J Rear combination lights B Sedan HGB012BB 1) Backup light 3) Brake light 2) Rear turn 4) Tail light signal light 5) Brake/tail light HGB011BA 2. Open the rear portion of the side trunk trim panel. 1. Remove the clip from the rear trunk trim with a 3.
Page 389 Maintenance and service B Wagon HGB014BA 2. Remove the upper and lower screws. Then, slide HGB013BA the rear combination lamp assembly to the rear and 1. Using a Phillips screwdriver, remove the upper remove it from the vehicle. and lower screws that secure the side cover of the rear combination light assembly.
Page 390: License Plate Light
Maintenance and service J License plate light HGB015CB 1) Tail/stop light 2) Rear turn signal light HGF012FA 3) Backup light 4) Rear side marker light 1. Remove the mounting screws using a phillips screwdriver. 3. Remove the bulb holder from the rear combina- 2.
Page 391 Maintenance and service J Room light, spot light and cargo area light HB0386 1) Bulb HSA005BA 1. Remove the lens by prying the edge of the lens with a regular screwdriver. 2. Pull the bulb out of the socket. Install a new bulb. 3.
Page 392: Trunk Light
Maintenance and service J Trunk light J High mount stop light B Sedan HG2009DA 1. Remove the cover by pulling it out. OM-H2350 2. Pull the bulb out of the socket. Install a new bulb. 1. Remove the high mount stop light cover by pry- 3.
Page 393 3. Remove the bulbs from the socket by pushing it and turning counterclockwise. Install a new bulb. 4. Reinstall the cover. 5. Tighten the mounting screws then reinstall the covers. NOTE Other bulbs may be difficult to replace. Have your SUBARU dealer replace these bulbs if necessary. 11-68...
Page 394: Specifications
Specifications Specifications 12-2 ........Dimensions 12-2 .
Page 395: Specifications
Specifications Specifications These specifications are subject to change without notice. J Dimensions in (mm) Item Sedan Wagon 2.5-liter 2.0-liter (Turbo) 2.5-liter 2.0-liter (Turbo) OUTBACK SPORT Drive system Transmission type Overall length 173.4 (4405) Overall Sedan 68.1 (1730) – width idth Wagon –...
Page 396: Electrical System
Specifications J Engine Engine model EJ251 EJ205 (2.5-liter, SOHC, non-turbo) (2.0-liter, DOHC, turbo) Engine type Horizontally opposed, liquid cooled 4 cylinder, 4-stroke gasoline engine Displacement cu in. (cc) 149.9 (2,457) 121.7 (1,994) Bore × Stroke in. (mm) 3.92 × 3.11 (99.5 × 79.0) 92.0 ×...
Page 397 Specifications J Capacities Fuel tank 15.9 US gal (60 liters, 13.2 Imp gal) Engine oil 2.5-liter engine model 4.2 US qt (4.0 liters, 3.5 Imp qt) Turbo engine model 4.8 US qt (4.5 liters, 4.0 Imp qt) Transmission oil (MT) 3.7 US qt (3.5 liters, 3.1 Imp qt) Transmission oil (AT) 10.0 US qt (9.5 liters, 8.4 Imp qt)
Page 398: Wheel Alignment
Specifications J Tires Tire size 195/60R15 88H P205/55R16 89V 215/45R17 87W 15 × 6 JJ 16 × 6 17 × 7 JJ Wheel size Pressure Front 32 psi (220 kPa, 2.2 kg/cm 33 psi (230 kPa, 2.3 kg/cm Rear 29 psi (200 kPa, 2.0 kg/cm 32 psi (220 kPa, 2.2 kg/cm Temporary spare tire...
Page 399: Fuses And Circuits
Specifications Fuses and circuits Fuse panel Fuse rating Circuit J Fuse panel located behind the coin D Heater fan tray D Heater fan D Power door lock D Keyless entry D Cigarette lighter D Remote controlled rear view mirrors D Tail light D Parking light D SRS airbag D Fog light...
Page 400 Specifications Fuse panel Fuse rating Circuit D Illumination bright- ness control D Combination meter D SRS lamp D Rear window wiper and washer D Windshield wiper and washer D Brake light D Air conditioner D Backup light D Cruise control D Mirror heater –...
Page 401: Compartment
Specifications J Fuse panel located in the engine Fuse panel Fuse rating Circuit compartment D Radiator cooling fan (Main) D Radiator cooling fan (Sub) D ABS motor D Rear window defog- D Hazard warning flasher D Horn D Turn signal lights D Automatic transmis- sion control unit D Alternator...
Page 402: Headlights
Specifications Bulb chart Description Wattage Bulb type Luggage compartment 12V-13W — Description Wattage Bulb type light Front ashtray light 12V-1.4W — Headlight 12V-60/55W 9007 (HB3) Room light 12V-8W — Front fog light 12V-55W — Spot light 12V-8W — Front turn signal 12V-21W —...
Page 403: Vehicle Identification
Specifications Vehicle identification Vehicle identification number Emission control label Vacuum hose connections label Tire inflation pressure label Certification plate Bar cord label Vehicle identification number plate Model number plate HGD003BB 12-10...
Page 404: Consumer Information And Reporting Safety Defects
Consumer information and Reporting safety defects Uniform tire quality grading standards 13-2 ..Treadwear 13-2 ......... . . Traction AA, A, B, C 13-2 .
Page 405: Uniform Tire Quality Grading Standards
Consumer information and Reporting safety defects J Treadwear For U.S.A. The following information has been compiled ac- The treadwear grade is a comparative rating based cording to Code of Federal Regulations “ Title 49, on the wear rate of the tire when tested under con- Part 575”...
Page 406 Consumer information and Reporting safety defects WARNING WARNING The traction grade assigned to this tire is The temperature grade for this tire is estab- based on straight-ahead braking traction lished for a tire that is properly inflated and tests, and does not include acceleration, cor- not overloaded.
Page 407 However, NHTSA cannot be- come involved in individual problems be- tween you, your dealer, or Subaru of Amer- ica, Inc. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in the Wash- ington D.C.
Page 408: Index
Index 14-1...
Page 409 Index ABS (Anti-lock Brake System) 7-22 Battery 11-50 ..............ABS system self-check 7-23 Brake booster...
Page 410 Index CHECK ENGINE warning light/ Malfunction Cooling and dehumidifying in high humidity and indicator lamp 3-10 low temperature weather condition 4-11 ........
Page 411 Index Engine 12-3 Fuel filler lid and cap ........... .
Page 412 Index Keyless entry system (if equipped) ... . . Key number If no steam is coming from the engine ..........Key reminder chime compartment 9-14...
Page 413 Index Meters and gauges Power steering 7-20 ........
Page 414 Index Recommended spark plugs 11-21 Snow tires 8-13 ..............Refrigerant for your climate control system 4-11 Sounding a panic alarm...
Page 415 Index Synthetic leather upholstery 10-6 To temporarily cancel the cruise control 7-28 ....... System monitors 1-25 To turn off the cruise control...
Page 416 Index Valet mode 2-15 ..........Vanity mirror (if equipped) .
Page 418 GAS STATION REFERENCE Fuel: Fuel capacity: 2.5 Liter models: 15.9 US gal (60 liters, 13.2 Imp gal) Use only unleaded gasoline with an octane Engine oil: rating of 87 AKI or higher. Use only API classification SJ or SH with the 2.0 Liter (Turbo) models: words “ENERGY CONSERVING II”...

This manual is also suitable for:

Outback sport 20022002 imprezaHgf008aa Hgf009aa

Subaru IMPREZA 2002 Owner's Manual

Table of Contents

J Tire Changing Tools

Front Seats

Seat Heater (if Equipped)

Rear Seats

Seatbelts

Front Seatbelt Pretensioners

Child Restraint Systems

SRS Airbag

Keys and Doors

Keys

Door Locks

Power Door Locking Switches (if Equipped)

Keyless Entry System (if Equipped)

Security System (if Equipped)

Child Safety Locks

Windows

Trunk Lid (Sedan)

Rear Gate (Wagon)

Instruments and Controls

Interior Equipment

Starting and Operating

Driving Tips

In Case of Emergency

Maintenance and Service

Quick Links

Chapters

Related Manuals for Subaru IMPREZA 2002

Summary of Contents for Subaru IMPREZA 2002