Page 1 2008 Chevrolet Uplander Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-6 Safety Belts ... 1-23 Child Restraints ... 1-42 Airbag System ... 1-77 Restraint System Check ... 1-91 Features and Controls ... 2-1 Keys ...
Page 2: Using This Manual
We reserve the right to make changes after that time without further notice. For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division whenever it appears in this manual. This manual describes features that may be available in this model, but your vehicle may not have all of them.
Page 3 Index A good place to quickly locate information about the vehicle is the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Safety Warnings and Symbols There are a number of safety cautions in this book.
Page 4 Vehicle Damage Warnings You will also ﬁnd notices in this manual. Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 5: Table Of Contents
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Power Seats ...1-3 Heated Seats ...1-3 Reclining Seatbacks ...1-4 Head Restraints ...1-6 Rear Seats ...1-6 Rear Seat Operation ...1-6 Bucket Seats ...1-6 Captain Chairs ...1-14 Third Row Seat ...1-18 Safety Belts ...1-23 Safety Belts: They Are for Everyone ...1-23 How to Wear Safety Belts Properly ...1-28 Lap-Shoulder Belt ...1-36...
Page 6 Front Seats Manual Seats Use the lever located on the front of the seat to adjust the seat forward or rearward. Pull up on the lever to unlock the seat. Slide the seat to where you want it and release the lever. CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle...
Page 7 Power Seats If the vehicle has power seats, the controls used to operate them are located on the outboard side of the seats. To adjust the seat, do any of the following: • Move the seat forward or rearward by sliding the control forward or rearward.
Page 8 Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Page 9 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 10 Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash. The height of the head restraints can be adjusted on the ﬁrst and second row seats.
Page 11 Fold and Tumble Feature CAUTION: Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.
Page 12 4. Release the rear set of seat hooks from the ﬂoor pins by pulling the nylon strap, located at the base of the seat. Use the strap to guide the seat forward. To return the seat to the original position, do the following: 1.
Page 13 Adjusting the Bucket Seats Forward and Rearward There are two adjustment levers on the second row bucket seats that enable them to move forward or rearward. One is located below the front of the seat. The other lever is located on the rear of the seat.
Page 14 Folding or Reclining the Seatbacks The seatback on a bucket seat can either be folded forward or reclined using the nylon strap or the recline lever. Nylon Strap To fold the seatback forward, do the following: 1. Pull the nylon strap, located on the rear right hand side of the seat, or lift the recline lever, located on the front right hand side of the seatback to release the seatback.
Page 15: Removing The Bucket Seats
To recline the seatback, do the following: 1. Pull the nylon strap or lift the recline lever. 2. Press back on the seatback until it is in the desired position 3. Let go of the strap or lever. Removing the Bucket Seats To remove the bucket seats, do the following: 1.
Page 16 5. To release the front seat hooks from the ﬂoor pins, squeeze the angled bar, located beneath the seat toward the straight crossbar. 6. Remove the seat by rocking it slightly forward, then toward the rear of the vehicle while pulling it out. This should be done in one motion.
Page 17 To reinstall the bucket seats, do the following: 1. With the seat folded, squeeze the angled bar beneath the seat toward the straight crossbar, while placing the front hooks of the seat into the front two ﬂoor pins. 2. Make sure the seat is angled so that the front seat hooks clear the ﬂoor pins.
Page 18 5. Pull the nylon strap, located on the rear right hand side of the seat, or lift the recline lever, located on the front right hand side of the seatback, to raise the seatback to the upright position. CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash.
Page 19 Folding or Reclining the Seatbacks CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked.
Page 20 The armrests can be lowered or raised for easier entry or exit of the vehicle. If your vehicle has captain chairs with side impact airbags, they will have one armrest on the inboard side. Removing a Captain Chair (without a Side Impact Airbag) If your vehicle has captain chairs with side impact airbags, the seats cannot be removed.
Page 21 Installing a Captain Chair (without a Side Impact Airbag) CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After installing the seat, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Page 22 2. Push the rear of the seat down to lock the rear latches onto the rear set of ﬂoor pins. 1-18 CAUTION: A seat that is not locked into place properly can move around in a collision or sudden stop. People in the vehicle could be injured.
Page 23 Folding the Seatback(s) Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. To fold down either side of the 50/50 split bench seat, lift the lever located on the back of the seat you want to fold, and push the seatback down.
Page 24 3. From the rear of the vehicle, locate the pullstrap attached to the lever on the back of the seat and pull it to raise the seat. 4. Push and pull on the seatback to make sure that it is locked into place. 1-20 Removing the Third Row Seat 1.
Page 25 4. From behind the seat, squeeze the release handle until the pin indicators are fully out. This indicates that the rear latches are released from the ﬂoor. For ease of removing the seat, squeeze the handle with the palm of your hand up. 5.
Page 26 For ease of installing the seat, put the seat in the folded position before beginning this procedure. 1. From the rear of the vehicle, place the front hooks of the seat onto the front ﬂoor pins in the third row. To do this, the seat will need to be angled approximately 8-10 inches (20-25 cm) from the ﬂoor so the front hooks clear the rear ﬂoor pins...
Page 27 Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Do not let anyone ride where he or she cannot wear a safety belt properly.
Page 28: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it is just a seat on wheels. 1-24...
Page 29 Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-25...
Page 30 or the instrument panel... 1-26 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Page 31 Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 32 How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see Older Children on page 1-42 or Infants and Young Children on page 1-46.
Page 33 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 34 What is wrong with this? The lap belt is too loose. It will not give as much protection this way. 1-30 CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 35 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 36 What is wrong with this? The belt is over an armrest. 1-32 CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt.
Page 37 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 38 What is wrong with this? The belt is behind the body. 1-34 CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 39 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 40 Lap-Shoulder Belt All seating positions in your vehicle have a lap-shoulder belt. Here is how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2.
Page 41 5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should go back out of the way.
Page 42 Shoulder Belt Height Adjuster Your vehicle has a shoulder belt height adjuster for the driver and right front passenger. Adjust the height so that the shoulder portion of the belt is centered on your shoulder. The belt should be away from your face and neck, but not falling off your shoulder.
Page 43 There is one guide for each second row passenger position. If your vehicle has a third row, there is one guide for each outboard position. Here is how to install a comfort guide to the shoulder belt: 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide.
Page 44 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top. 1-40 CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Page 45 4. Buckle, position, and release the safety belt as described in previously in this section. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guide, squeeze the belt edges together so that you can take them out of the guide.
Page 46 Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 47 The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue.
Page 48 CAUTION: Never do this. Here two children are wearing the same belt. The belt cannot properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. 1-44...
Page 49 CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. In a crash, the child would not be restrained by the shoulder belt. The child might slide under the lap belt. The belt force would then be applied right on the abdomen.
Page 50 Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 51 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 52 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 53 CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 54 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. 1-50 Securing an Add-On Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly...
Page 55 To help reduce the chance of injury, the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LATCH system.
Page 56 Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint;...
Page 57: Lower Anchors And Tethers For Children (Latch)
If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, we recommend that rear-facing child restraints not be transported in your vehicle, even if the airbag is off. When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle.
Page 58 In order to use the LATCH system in your vehicle, you need a child restraint that has LATCH attachments. The child restraint manufacturer will provide you with instructions on how to use the child restraint and its attachments. The following explains how to attach a child restraint with these attachments in your vehicle.
Page 59 Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Page 60 Lower Anchor and Top Tether Anchor Locations Seating positions with top tether anchors. (Lower Anchor): Seating positions with two lower anchors. Second Row Seating positions with top tether anchors. Third Row 1-56 (Top Tether Anchor): For the second row seating positions, the top tether anchors are located on the seatback, near the base of each seat.
Page 61 Second Row For the center third row position, if your vehicle has one, the top tether anchor is located on the seatback, near the center of the third row seating position. This anchor can accommodate only one top tether. Third Row Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that...
Page 62: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchors, or use the vehicle’s safety belts to secure the restraint, following the...
Page 63 CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Secure any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed.
Page 64 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2.
Page 65: Securing A Child Restraint In A
If the position you are using has an adjustable headrest or head restraint and you are using a single tether, raise the headrest or head restraint and route the tether under the headrest or head restraint and in between the headrest or head restraint posts.
Page 66 If you need to install more than one child restraint in the rear seat, be sure to read Where to Put the Restraint on page 1-52. 1. Put the child restraint on the seat. 2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint.
Page 67 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 68: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position Your vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-52. In addition, your vehicle has a passenger sensing system which is designed to turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag (if equipped) under certain conditions.
Page 69 If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, we recommend that rear-facing child restraints not be transported in your vehicle, even if the airbag is off. If your child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-53 for how to install your child restraint using LATCH.
Page 70 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if necessary.
Page 71 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 72: Built-In Child Restraint
Built-In Child Restraint WARNING! DEATH or SERIOUS INJURY can occur: • Follow all instruction on the child restraint and in the vehicle’s owner’s manual. If your vehicle has this feature, the built-in child restraint is located in the passenger-side position in the second row.
Page 73 CAUTION: Using the vehicle’s built-in child restraint as a booster seat for a larger child could cause injury to the child in a sudden stop or crash. A child whose weight is over 40 lbs (18 kg), whose height is over 40 in (1 016 mm) or whose shoulders are above the shoulder belt slots for the harness system should use a restraint system that is appropriate for their...
Page 74 2. Rotate the head restraint rearward until it touches 3. Lower the child restraint cushion. the top of the seatback. Make sure there is no gap between the lower edge of the head restraint and the top of the seatback. 1-70...
Page 75 You will be using the child restraint’s harness (A) to secure your child. Do not use the vehicle’s safety belts. CAUTION: Using the vehicle’s regular safety belts on a child seated on the built-in child restraint cushion can cause serious injury to the child in a sudden stop or crash.
Page 76 5. Place the child on the child restraint cushion. 6. Select only one side of the harness. Place the harness over the child’s shoulder. 7. Push the latch plate (A) into the buckle until it clicks. Be sure the buckle is free of any foreign objects that may prevent you from securing the latch plates.
Page 77 11. Now fasten the left and right halves of the shoulder harness clip together. The clip can be easily pulled apart and is designed to pull apart during a collision. CAUTION: A built-in child restraint harness that is not properly adjusted can cause injury to the child in a sudden stop or collision.
Page 78 13. Adjust the position of the harness on the child’s shoulder by moving the clip along the harness until it is level with the child’s armpits. On each side of the harness, the shoulder part should be centered on the child’s shoulder.
Page 79 2. Unlatch the harness by pushing the button on the buckle. 3. Move one side of the harness off the child’s shoulder. 4. Move the other side of the harness off the child’s shoulder. 5. Remove the child from the child restraint cushion. Storing the Built-In Child Restraint Always properly store the built-in child restraint before using the vehicle’s lap-shoulder belt.
Page 80 2. Fold the child restraint cushion and leg rest up into the seatback. 3. Press the child restraint cushion ﬁrmly into the seatback. 1-76 4. Then press the leg rest ﬁrmly into the seatback, and secure it by pressing the upper corners against the fastener strips on the seatback.
Page 81: Airbag System
5. Rotate the head restraint forward and push it all the way down. Just like the other restraint systems in your vehicle, your built-in child restraint needs to be periodically checked and may need to have parts replaced after a crash. See Checking the Restraint Systems on page 1-91 and Replacing Restraint System Parts After a Crash on page 1-92.
Page 82 Airbags are designed to supplement the protection provided by safety belts. Even though today’s airbags are also designed to help reduce the risk of injury from the force of an inﬂating bag, all airbags must inﬂate very quickly to do their job. Here are the most important things to know about the airbag system: CAUTION:...
Page 83 CAUTION: Airbags inﬂate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward.
Page 84: Where Are The Airbags
Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel. 1-80 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side.
Page 85 Driver Side shown, Passenger Side similar If your vehicle has seat-mounted side impact airbags for the driver and right front passenger, they are in the side of the seatbacks closest to the door. If your vehicle has second row captain’s chairs, the seat-mounted side impact airbags (if equipped) are in the side of the seatback closest to the door.
Page 86: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 87: What Makes An Airbag Inﬂate
In any particular crash, no one can say whether an airbag should have inﬂated simply because of the damage to a vehicle or because of what the repair costs were. For frontal airbags, inﬂation is determined by what the vehicle hits, the angle of the impact, and how quickly the vehicle slows down.
Page 88: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After the frontal and seat-mounted side impact airbags inﬂate, they quickly deﬂate, so quickly that some people may not even realize the airbags inﬂated. Some components of the airbag module may be hot for several minutes.
Page 89: Passenger Sensing System
In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for the airbag system.
Page 90 The passenger sensing system will turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag (if equipped) under certain conditions. The driver’s airbags are not part of the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger’s seat and safety belt.
Page 91 If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, we recommend that rear-facing child restraints not be transported in your vehicle, even if the airbag(s) are off. The passenger sensing system is designed to turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag (if equipped) if: •...
Page 92 The passenger sensing system is designed to enable (may inﬂate) the right front passenger’s frontal airbag and seat-mounted side impact airbag (if equipped) anytime the system senses that a person of adult size is sitting properly in the right front passenger’s seat. When the passenger sensing system has allowed the airbag or airbags to be enabled, the on indicator will light and stay lit to remind you that the airbag or airbags are active.
Page 93 If you ever pull the shoulder portion of the belt out all the way, you will engage the child restraint locking feature. This may unintentionally cause the passenger sensing system to turn the airbag(s) off for some adult size occupants. If this happens, just let the belt go back all the way and start again.
Page 94: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. Your dealer/retailer and the service manual have information about servicing your vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 7-15.
Page 95: Restraint System Check
This could either prevent proper deployment of the passenger airbag(s) or prevent the passenger sensing system from properly turning off the passenger airbag(s). See Passenger Sensing System on page 1-85. If you have any questions about this, you should contact Customer Assistance before you modify your vehicle.
Page 96: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 97: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry (RKE) System ...2-4 Remote Keyless Entry (RKE) System Operation ...2-5 Remote Vehicle Start ...2-8 Doors and Locks ...2-10 Door Locks ...2-10 Power Door Locks ...2-11 Delayed Locking ...2-12 Automatic Door Lock ...2-12 Programmable Automatic Door Unlock ...2-13 Lockout Protection ...2-13 Dual Sliding Doors ...2-13 Power Sliding Door (PSD) ...2-16...
Page 98 Section 2 Mirrors ...2-43 Manual Rearview Mirror ...2-43 Outside Power Mirrors ...2-43 Outside Convex Mirror ...2-44 Outside Heated Mirrors ...2-44 Object Detection Systems ...2-44 Ultrasonic Rear Parking Assist (URPA) ...2-44 ® OnStar System ...2-47 Universal Home Remote System ...2-51 Universal Home Remote System ...2-51 Universal Home Remote System Operation (With One Triangular LED) ...2-51 Features and Controls...
Page 99: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and they could be seriously injured or killed if caught in the path of a closing...
Page 100: Remote Keyless Entry (Rke) System
® Any new PASS-Key III key must be programmed before it will start your vehicle. See PASS-Key page 2-29 for more information on programming your new key. Notice: If you ever lock your keys in your vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys.
Page 101 Remote Keyless Entry (RKE) System Operation You can lock and unlock the vehicle’s doors and the liftgate using the Remote Keyless Entry (RKE) transmitter supplied with your vehicle. The RKE transmitter shown here is for a vehicle equipped with the remote vehicle start feature and dual power sliding doors.
Page 102: Remote Power Sliding Door Operation
When you use your RKE transmitter to unlock your vehicle the turn signal lamps will ﬂash to let you know the command was received. (Remote Alarm): When you press the horn button on the RKE transmitter, the turn signal lamps will ﬂash and the horn will sound.
Page 103: Battery Replacement
Matching Transmitter(s) to Your Vehicle Each RKE transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer/retailer. Remember to bring any remaining transmitters with you when you go to your dealer/retailer. When the dealer/retailer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched.
Page 104: Remote Vehicle Start
Remote Vehicle Start This feature allows you to start the engine from outside the vehicle. It may also turn the rear window defogger if the outside temperature is below 45°F (7°C). Laws in some local communities may restrict the use of remote starters.
Page 105 After your vehicle’s engine has been started two times using the remote start button, the vehicle’s ignition switch must be turned to ON/RUN and then back to LOCK/OFF using the key before the remote start procedure can be used again. After entering the vehicle during a remote start, insert and turn the key to ON/RUN to drive the vehicle.
Page 106: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 107: Power Door Locks
From the inside, use the manual or power door locks. To unlock either front door from the inside, pull back on the manual lever. To lock either front door from the inside, push the manual lever forward. Power Door Locks Your vehicle has power door locks.
Page 108: Delayed Locking
Delayed Locking This feature allows the locking of the vehicle to be delayed until all doors have been closed for approximately ﬁve seconds. To activate the delayed locking feature, do one of the following: • Press the driver’s door power lock switch one time while the driver’s door is open.
Page 109: Programmable Automatic Door Unlock
Programmable Automatic Door Unlock Your vehicle was programmed so that all doors will unlock automatically when the shift lever is moved into PARK (P). To change the way the automatic door unlocking operates, see DIC Vehicle Personalization (Uplevel Only) on page 3-76. Lockout Protection The lockout protection feature makes it more difficult to lock the key in the vehicle.
Page 110: Sliding Door Lock
Sliding Door Lock 2-14 CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut be sure to hold it open until everyone is clear of the door, and only then allow it to slowly close.
Page 111: Sliding Door Security Lock
Lock either sliding door from inside the vehicle by moving the manual lever down. Unlock it by moving the lever up. With the power door locks, the sliding door lock has a delay feature. See Delayed Locking on page 2-12 and DIC Vehicle Personalization (Uplevel Only) on page 3-76.
Page 112: Power Sliding Door (Psd)
If your vehicle has power sliding door(s), you can prevent power opening of the sliding door from the passenger power sliding door (PSD) activation switch by pressing the PSD second row passenger override (deactivation) switch located on the overhead console. See Power Sliding Door (PSD) on page 2-16.
Page 113 Power Sliding Door (PSD) Switches Your vehicle will have one of the following switch(es) located on the overhead console switchbank. If your vehicle has a single power sliding door (PSD), you have this switch. PSD Activation/Override (Deactivation) Switch If your vehicle has dual power sliding doors, you have these switches.
Page 114 Your vehicle also has passenger power sliding door activation switch(es). Passenger PSD Activation Switch If you have a single PSD, this switch is located in front of the passenger side sliding door. If your vehicle has dual PSDs, the switches are located in front of both sliding doors.
Page 115 If a power sliding door is locked, it cannot be unlocked and opened using the overhead console PSD switch(es) or the passenger PSD activation switch(es). The power sliding door must either be manually unlocked or unlocked using the power door unlock switch located on the driver’s or front passenger’s armrest, and then opened using the overhead or passenger PSD activation switch(es).
Page 116 If an object obstructs the power sliding door(s) while it is closing, the door will automatically reverse to the open position, provided it meets sufficient resistance. Resistance must be as strong as the force of the closing door, or stronger. The force of the closing door increases signiﬁcantly as the door approaches the latched position.
Page 117: Resetting The Power Sliding Door
CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut, turn on the power sliding door feature.
Page 118: Liftgate
If any of these conditions occur, the power sliding door may need to be reset. If your vehicle has the dual power sliding doors, both doors will have to be reset. To reset a door, do the following: 1. Check to be sure the power sliding door is unlocked and securely closed.
Page 119 CAUTION: It can be dangerous to drive with the liftgate open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate:...
Page 120: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 121: Power Windows
Power Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome from extreme heat in warm or hot weather and suffer permanent injuries or even death from heat stroke. Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
Page 122: Manual Rear Quarter Windows
Manual Rear Quarter Windows Your vehicle may have manual rear quarter windows. To open, pull the latch forward to release it, then swing the window outward. Press the center of the latch to secure the window in the open position. To close, pull the center of the latch forward and then close the latch.
Page 123: Sun Visors
Sun Visors To block out glare, swing down the sun visors. You can also remove them from the center mount and swing them to the side. The sun visors can also slide along the rod to cover different areas of the front window. Visor Vanity Mirror Your vehicle may have a visor vanity mirror.
Page 124: Arming With The Power Lock Switch
Arming with the Power Lock Switch Your alarm system will arm when the key is removed from the ignition and you use the driver’s power door lock switch, with the driver’s door open or the passenger’s door power door lock switch with the passenger’s door open to lock the vehicle.
Page 125: Pass-Key
Disarming with Your Key Your alarm system will disarm when you use your key to unlock the driver’s door. The security light will stop ﬂashing to let you know the system is no longer armed. If you would like your key not to disarm the alarm system, see DIC Vehicle Personalization (Uplevel Only) on page 3-76.
Page 126 If the engine still does not start, and the key appears to be undamaged, try another ignition key. If the engine still does not start with the other key, your vehicle needs service. If your vehicle does start, the ﬁrst key may be faulty.
Page 127: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km).
Page 128: Retained Accessory Power (Rap)
B (ACC/ACCESSORY): This is the position in which you can operate the electrical accessories, such as the radio. C (ON/RUN): This is the position to which the switch returns after the engine is started and the ignition key is released. This is the position for driving. Even while the engine is not running, ON/RUN can be used to operate your electrical accessories and to display some instrument panel warning lights.
Page 129 Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Do not race the engine immediately after starting it.
Page 130: Engine Coolant Heater
Engine Coolant Heater The engine coolant heater, if available, can help in cold weather conditions at or below 0°F (−18°C) for easier starting and better fuel economy during engine warm-up. Plug in the coolant heater at least four hours before starting your vehicle.
Page 131: Automatic Transmission Operation
Automatic Transmission Operation Maximum engine speed is limited when you are in PARK (P) or NEUTRAL (N), to protect driveline components from improper operation. There are several different positions for your shift lever. PARK (P): This gear position locks your front wheels. It is the best position to use when you start your engine because your vehicle cannot move easily.
Page 132 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped.
Page 133 Warm-Up Shift Your vehicle has a computer controlled transmission designed to warm up the engine faster when the outside temperature is 35°F (2°C) or colder. You may notice that the transmission will shift at a higher vehicle speed until the engine is warmed up. This is a normal condition designed to provide heat to the passenger compartment and defrost the windows more quickly.
Page 134: Parking Brake
Parking Brake The parking brake is located under the instrument panel on the driver’s side of the vehicle. To set the parking brake, hold the regular brake pedal down with your right foot and push down on the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on.
Page 135: Leaving Your Vehicle With The Engine Running
3. Turn the ignition key to LOCK/OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Leaving Your Vehicle With the Engine Running CAUTION: It can be dangerous to leave your vehicle with...
Page 136: Shifting Out Of Park (P)
Shifting Out of PARK (P) This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: • Prevent ignition key removal unless the shift lever is in PARK (P) with the shift lever button fully released, and •...
Page 137: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • The exhaust system sounds strange or different.
Page 138: Running The Engine While Parked
Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 139: Mirrors
Mirrors Manual Rearview Mirror When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you.
Page 140: Outside Convex Mirror
Outside Convex Mirror CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.
Page 141 CAUTION: The Ultrasonic Rear Parking Assist (URPA) system does not replace driver vision. It cannot detect: • objects that are below the bumper, underneath the vehicle, or if they are too close or far from the vehicle • children, pedestrians, bicyclists, or pets. If you do not use proper care before and while backing;...
Page 142: How The System Works
How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R). The rear display will then brieﬂy illuminate to let you know the system is working. URPA operates only at speeds less than 3 mph (5 km/h). If you are above this speed, the red light on the rear display will ﬂash.
Page 143: Onstar System
When the System Does Not Seem to Work Properly • The driver disabled the system. • The ultrasonic sensors are not clean, a red URPA display light may illuminate when the vehicle is in REVERSE (R). Keep your rear bumper free of mud, dirt, snow, ice and slush.
Page 144 OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar. A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature.
Page 145 OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility.
Page 146: How Onstar Service Works
How OnStar Service Works In order to provide you with OnStar services, your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys.
Page 147: Universal Home Remote System
Universal Home Remote System Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 148 Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming.
Page 149 Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons. 2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view.
Page 150 6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. 7. Firmly press and release the “Learn” or “Smart” button.
Page 151: Gate Operator And Canadian Programming
Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming.
Page 152: Storage Areas
Reprogramming a Single Universal Home Remote Button To reprogram any of the three Universal Home Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-5.
Page 153: Overhead Console (With Rail)
Overhead Console (With Rail) If your vehicle is equipped with an overhead console, it may contain the following: • Reading lamps. See Front Reading Lamps on page 3-19 or Rear Reading Lamps on page 3-19. • Switchbank. See Overhead Console Switchbank on page 3-21.
Page 154 4. Firmly press down making sure the latch is ﬂat with the ribs (A) on the storage bin. 5. Switch hands and repeat Steps 2 through 4 for the latch on the opposite side of the storage bin. 6. Reverse these steps in order to remove the storage bin.
Page 155: Floor Console Storage Area
Floor Console Storage Area Your vehicle may have a storage compartment located on the front console below the front cupholders. Pull up and then forward on the handle to open the storage compartment. Folding Tray Your vehicle may be equipped with folding convenience trays located between seats.
Page 156: Luggage Carrier
Replacing the Center Console CAUTION: A second row center console that is not locked into place properly can move around in a crash or sudden stop. People in the vehicle could be injured. Be sure to lock the console into place properly when installing it. 1.
Page 157: Convenience Net
Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-21. To prevent damage or loss of cargo as you are driving, check now and then to make sure the cargo is still securely fastened.
Page 158 Convenience Center CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle may have a convenience center. It provides extra storage space for the rear of the vehicle.
Page 159: Replacing The Convenience Center
Replacing the Convenience Center 1. Make sure the third row seat is properly installed in the vehicle. See Third Row Seat on page 1-18 for more information. If the third row seat is not in the vehicle with the convenience center, the convenience center will not be locked into the correct position in the vehicle.
Page 160 NOTES 2-64...
Page 161 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-7 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-9 Windshield Washer ...3-9 Rear Window Wiper/Washer ...3-10 Cruise Control ...3-10 Exterior Lamps ...3-14...
Page 162 Section 3 Warning Lights, Gages, and Indicators ...3-34 Instrument Panel Cluster ...3-35 Speedometer and Odometer ...3-36 Trip Odometer ...3-36 Tachometer ...3-36 Safety Belt Reminders ...3-36 Airbag Readiness Light ...3-37 Passenger Airbag Status Indicator ...3-38 Charging System Light ...3-40 Brake System Warning Light ...3-41 Antilock Brake System Warning Light ...3-42 Traction Control System (TCS) Warning Light ...3-42 Engine Coolant Temperature Gage ...3-43...
Page 163 NOTES...
Page 164: Instrument Panel Overview
Instrument Panel Overview...
Page 165 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-30. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 3-119. D.
Page 166: Hazard Warning Flashers
Hazard Warning Flashers The hazard warning ﬂashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located towards the center of the instrument panel.
Page 167: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane Change Signals. See Turn and Lane-Change Signals on page 3-7. • Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. •...
Page 168: Headlamp High/Low-Beam Changer
To signal a lane change, just raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. As you signal a turn or a lane change, if the arrow ﬂashes faster than normal, a signal bulb may be burned out and other drivers will not see your turn signal.
Page 169: Windshield Wipers
Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it. (Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer.
Page 170: Rear Window Wiper/Washer
Rear Window Wiper/Washer CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. If your vehicle has the rear window washer/wiper, the controls are located on the end of the turn signal/ multifunction lever.
Page 171 If your vehicle has cruise control, the lever is located below the windshield wiper control on the right side of the steering wheel. RES + (Resume/Accelerate): Push the lever up to resume the cruise control speed, or to accelerate when passing another vehicle. (CRUISE CONTROL) ON/OFF button on the end of the lever to turn the cruise control on.
Page 172: Setting Cruise Control
Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 173 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Push up on the cruise control lever toward the plus (resume/accelerate) position, then release the lever and take your foot off the accelerator pedal.
Page 174: Exterior Lamps
Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle’s speed, its load, and the steepness of the hills. When going up steep hills, the accelerator pedal might have to be used in order to maintain the vehicle’s speed.
Page 175: Wiper Activated Headlamps
AUTO (Automatic): Turn the control to this position to set your headlamps in automatic mode. AUTO mode, if enabled, will turn the exterior lamps on and off automatically depending on how much light is available outside the vehicle. Due to the momentary switch design, your automatic lights may be disabled even if the control is in the AUTO position.
Page 176: Daytime Running Lamps (Drl)/Automatic Headlamp System
Daytime Running Lamps (DRL)/ Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset.
Page 177: Instrument Panel Brightness
Instrument Panel Brightness The knob to adjust the instrument panel brightness is located in the center of the interior lamp controls. Turn the knob clockwise to brighten the lights and counterclockwise to dim them. Interior Lamps Control The interior lamp control is located to the right of the exterior lamp controls on the instrument panel to the...
Page 178: Dome Lamp
Dome Lamp The dome lamp is located in the headliner and has two buttons to manually turn it on or off. The dome lamp will come on each time you open a door, unless you turn on the interior lamps override feature. See Interior Lamps Control on page 3-17.
Page 179: Exit Lighting
Exit Lighting With exit lighting, the interior lamps will come on for about 25 seconds whenever you remove the key from the ignition. If you turn the ignition key to RUN or ACCESSORY, the lamps will fade out. The lamps will also fade out if you lock the doors with the power door lock switch or the remote keyless entry transmitter.
Page 180: Electric Power Management
Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in.
Page 181: Battery Run-Down Protection
Battery Run-Down Protection Your vehicle has a feature to help prevent you from draining the battery, in case you accidentally leave the interior lamps on. If you leave any interior lamps on while the ignition is in lock or off, they will automatically turn off after 10 minutes.
Page 182: Accessory Power Outlet(S)
Accessory Power Outlet(s) The accessory power outlets can be used to plug in electrical equipment such as a cellular telephone or CB radio. Your vehicle may have two accessory power outlets. There may be one outlet located below the climate controls on the instrument panel and one outlet located in the rear compartment on the driver’s side.
Page 183: Power Outlet 115 Volt Alternating Current
Power Outlet 115 Volt Alternating Current Your vehicle may have a power outlet that can be used to plug in electrical equipment that uses a maximum limit of 150 watts. The power outlet is located behind the third row seats on the passenger’s side rear quarter trim panel.
Page 184: Cigarette Lighter
Cigarette Lighter Your vehicle may have a cigarette lighter. To use the lighter, located on the instrument panel below the climate controls, push it in all the way and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot.
Page 185 Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets. (Bi-Level): This mode directs half of the air to the instrument panel outlets, then directs the remaining air to the ﬂoor outlets.
Page 186: Defogging And Defrosting
The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. MAX A/C (Maximum Air Conditioning): Turn the right knob to this position for maximum air conditioning.
Page 187: Dual Climate Control System
Rear Window Defogger If your vehicle has a rear window defogger a warming grid is used to remove fog from the rear window. < REAR: Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.
Page 188 Temperature Control: Use the driver’s and passenger’s levers to increase or decrease the air temperature inside your vehicle. Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: MAX A/C (Maximum Air Conditioning): Turn the right knob to this position for maximum air conditioning.
Page 189: Rear Window Defogger
The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. (Heated Seats): Press this button to turn on the heated seats.
Page 190: Outlet Adjustment
Outlet Adjustment Use the louvers located on the air outlets to change the direction of the airﬂow. Use the thumbwheels on the driver side and passenger side air outlets to open or close the airﬂow from these outlets. Operation Tips •...
Page 191 When the front climate control is in AUX and the rear climate control fan or temperature button is pressed, the display will show the same airﬂow modes as the front climate control system. See Dual Climate Control System on page 3-27. The front control must be in the AUX position to enable adjustment of the temperature and fan speed on the rear control system.
Page 192: Passenger Compartment Air Filter
Rear Air Outlets The outlet behind the driver side rear seat is for the cold air return. Be sure to keep it free from obstructions. Also, keep the area around the base of the center instrument panel console, between and under the front seats, free of objects that could also obstruct airﬂow to the rear seating area.
Page 193 2. Then push the tab, located on the left of the inner access panel, to the right. 3. The ﬁrst air ﬁlter will pull straight out. To remove the second, reach in and slide it toward the opening. Pull the second ﬁlter out. 4.
Page 194: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 195: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using, and many other things you’ll need to drive safely and economically.
Page 196: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper-resistant odometer.
Page 197: Airbag Readiness Light
Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-85 for more information.
Page 198: Passenger Airbag Status Indicator
If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly.
Page 199 CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag and seat-mounted side impact airbag (if equipped). A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates.
Page 200: Charging System Light
If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system.
Page 201: Brake System Warning Light
Brake System Warning Light When the ignition is on, the brake system warning light will come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem.
Page 202: Antilock Brake System Warning Light
Antilock Brake System Warning Light For vehicles with the Antilock Brake System (ABS), this light will come on brieﬂy when you start the engine. That is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the ABS light stays on, turn the ignition off, if the light comes on when you are driving, stop as soon as it is safely possible and turn the ignition off.
Page 203: Engine Coolant Temperature Gage
If the traction control system warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service. Engine Coolant Temperature Gage United States This gage shows the engine coolant temperature. If the red gage lamp turns on, your engine is too hot! It means that your engine coolant has overheated.
Page 204: Malfunction Indicator Lamp
When the Light Flashes First and Then is Solid This indicates that there may be a problem with the Tire Pressure Monitor System. The light will ﬂash for about a minute and then stay on solid for the remainder of the ignition cycle. This sequence will repeat with every ignition cycle.
Page 205: If The Light Is Flashing
This light comes on, as a check to show it is working, when the ignition is turned ON/RUN but the engine is not running. If the light does not come on, have it repaired. This light also comes on during a malfunction in one of two ways: •...
Page 206: If The Light Is On Steady
If the Light Is On Steady You might be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 207: Oil Pressure Light
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly.
Page 208: Security Light
When the light comes on and stays on, it means that oil is not ﬂowing through your engine properly. You could be low on oil and you might have some other system problem. Security Light For information regarding this light and the vehicle’s security system, see Content Theft-Deterrent on page 2-27.
Page 209: Fuel Gage
Fuel Gage United States When the indicator nears empty, you still have a little fuel left, but you should get more soon. Your fuel gage tells you about how much fuel you have left when the ignition is on. Here are four things some owners ask about. All these things are normal and do not indicate that anything is wrong with the fuel gage.
Page 210: Driver Information Center (Dic)
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All messages appear in the DIC display located in the instrument panel cluster, below the tachometer. The DIC buttons are located on the center of the instrument panel, below the center outlets. The DIC comes on when the ignition is on.
Page 211 DIC Buttons (Information): Press this button to display the odometer, trip distance, time elapsed, average speed, fuel economy, battery voltage, oil life, tire pressure readings, and to turn off the DIC. (Set/Reset): Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC.
Page 212 There is also a retroactive trip odometer function that performs the following for each trip odometer: • If the vehicle’s speed has exceeded 3 mph (5 km/h) during the current ignition cycle, this function will set the trip odometer to the distance driven during the current ignition cycle.
Page 213 Fuel Range Press the information button until FUEL RANGE displays. This mode shows the approximate number of remaining miles or kilometers the vehicle can be driven without refueling. Fuel range is based on several factors, including distance travelled, fuel used, fuel capacity, etc. This estimate will change if driving conditions change.
Page 214 Oil Life Press the information button until OIL LIFE displays. This mode shows an estimate of the oil’s remaining useful life. If you see OIL LIFE 99% on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions.
Page 215 Menu Button Items (Menu): Press this button to scroll through the following items: Units Press the menu button until UNITS displays. This mode allows you to select between English or Metric units of measurement. Once in this mode, press the set/reset button to select between ENGLISH or METRIC.
Page 216: Dic Compass (Uplevel Only)
DIC Compass (Uplevel Only) Your vehicle may have a compass in the Driver Information Center (DIC). Compass Zone The zone is set to zone eight upon leaving the factory. Your dealer/retailer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross-country trip or moving to a new state or province, it will be necessary to compensate for compass variance by resetting the zone through the...
Page 217: Compass Calibration
Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible.
Page 218: Dic Warnings And Messages
DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another.
Page 219: Battery Saver Active
BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping beyond a reasonable level. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed.
Page 220: Check Gas Cap
CHECK GAS CAP This message displays if the fuel cap is not on, or is not fully tightened. Check the fuel cap to ensure that it is on properly. See Filling the Tank on page 5-8 for more information. This message displays and a chime sounds while the ignition is in ON/RUN.
Page 221 DELAYED LOCKING This message displays to inform the driver that even though a door lock switch or the lock button on the Remote Keyless Entry (RKE) transmitter has been pressed, that actual locking of the doors is being delayed because the delayed locking feature has been activated in the DIC.
Page 222: Engine Coolant Hot
ENGINE COOLANT HOT Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed.
Page 223: Key In Ignition
HOOD AJAR If your vehicle has the remote start feature, this message displays when the hood is not closed properly. Make sure that the hood is closed completely. See Hood Release on page 5-11. This message displays while the ignition is in ON/RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
Page 224 LEFT FRONT TURN LAMP OUT This message displays when the left front turn signal bulb needs to be replaced. See Headlamps and Sidemarker Lamps on page 5-42. This message displays while the ignition is in ON/RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
Page 225: Low Fuel
LOW BRAKE FLUID This message displays when the brake ﬂuid level is low. Have the brake system serviced by your dealer/retailer as soon as possible. See Brakes on page 5-33 for proper ﬂuid level. The brake system warning light also appears on the instrument panel cluster when this message appears on the DIC.
Page 226 This message cannot be acknowledged and cleared from the screen. This message re-displays for a few seconds if the condition still exists when the engine is turned off. If the condition still exists, the message re-appears when the engine is turned on. PARKING BRAKE ON This message displays to alert the driver when the vehicle’s parking brake is on, the ignition is in ON/RUN,...
Page 227: Reduced Engine Power
PASSENGER’S REAR DOOR AJAR This message displays when the passenger side rear door is not closed properly. Make sure that the door is closed completely. This message displays while the ignition is in ON/RUN. A chime sounds when the ignition is shifted out of PARK (P).
Page 228 REDUCED POWER STOP WHEN SAFE This message displays when your vehicle is in an overheated engine operating mode. This operating mode allows your vehicle to be driven to a safe place in an emergency. In this mode, you will notice a signiﬁcant loss in power and engine performance.
Page 229: Right Rear Turn Lamp Out
REMOTE START ON If your vehicle has the remote start feature, this message displays when a remote start is initiated. See “Remote Vehicle Start” under Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. RIGHT FRONT TURN LAMP OUT This message displays when the right front turn signal bulb needs to be replaced.
Page 230: Service Abs System
SERVICE ABS SYSTEM This message displays when the vehicle’s Antilock Brake System (ABS) is not functioning properly. Have the ABS serviced by your dealer/retailer as soon as possible. The ABS warning light also appears on the instrument panel cluster when this message appears on the DIC.
Page 231: Service Brake System
SERVICE BRAKE SYSTEM This message displays when a problem with the brake system has been detected. Have your vehicle serviced by your dealer/retailer as soon as possible. The brake system warning light also appears on the instrument panel cluster when this message appears on the DIC.
Page 232: Service Tire Monitor System
SERVICE STABILITY SYSTEM ® If your vehicle has StabiliTrak , this message displays if there has been a problem detected with StabiliTrak ® See StabiliTrak System on page 4-7. If this message turns on while you are driving, pull off the road as soon as possible and stop carefully.
Page 233: Service Traction System
SERVICE TRACTION SYSTEM If your vehicle has the Traction Control System (TCS), this message displays when the system is not functioning properly. A warning light also appears on the instrument panel cluster. See Traction Control System (TCS) Warning Light on page 3-42. See Traction Control System (TCS) on page 4-6 for more information.
Page 234: Stability Control Off
STABILITY CONTROL OFF ® If your vehicle has StabiliTrak , this message displays any time the system turns off. When this message has ® been displayed, StabiliTrak is no longer available to assist you with directional control of the vehicle. Adjust your driving accordingly.
Page 235: Turn Signal On
Any of the following conditions may cause the TCS to turn off: • The TCS is turned off by pressing the traction control button located on the center of the instrument panel. See Traction Control System (TCS) on page 4-6. •...
Page 236: Dic Vehicle Personalization (Uplevel Only)
DIC Vehicle Personalization (Uplevel Only) Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. The customization features include the following: •...
Page 237 Entering the Personal Program Menu 1. Turn the ignition on and place the vehicle in PARK (P). To avoid excessive drain on the battery, it is recommended that the headlamps are turned off. 2. Press the menu button until PERSONAL PROGRAM displays.
Page 238 ALL KEYS RESET This screen will only display if YES was selected on the FACTORY DEFAULTS screen. Press the set/reset button to scroll through the following choices: CANCEL (default): The features will not be set to their factory default settings and the DIC will return to the FACTORY DEFAULTS screen.
Page 239 DELAYED LOCKING This feature allows the locking of the vehicle to be delayed until all of the doors have been closed for about ﬁve seconds. When the delayed locking feature is enabled, it may be activated when the key is out of the ignition by doing one of the following: •...
Page 240 CONTENT THEFT If your vehicle has the content theft-deterrent system, once this feature is turned on, the system will activate if someone tries to enter the vehicle without using the RKE transmitter or the correct key. It will also activate when an incorrect key is used in the ignition. Press the menu button until CONTENT THEFT appears on the DIC display.
Page 241 REMOTE START If your vehicle has remote start, this feature allows the remote start to be turned OFF or ON. The remote start feature allows you to start the engine from outside of the vehicle using the RKE transmitter. See Remote Vehicle Start on page 2-8 for more information.
Page 242 Personalization Menu Items The following are personalization features that allow you to program setting for up to two drivers: PERSONALIZE KEY If you are using a key that has already been personalized to be recognized as key 1 or 2, this screen will not display.
Page 243 AUTO DOOR UNLOCK This feature allows automatic door unlocking to be turned off, used for the driver’s door only, or for all of the doors. Press the menu button until AUTO DOOR UNLOCK appears on the DIC display. Press the set/reset button to scroll through the following choices: OFF: None of the doors will unlock when the vehicle is shifted into PARK (P) or the key is taken out of the...
Page 244: Audio System(S)
FOB UNLOCK ON 1ST PRESS This feature allows the selection of which doors will unlock on the ﬁrst press of the unlock button on the RKE transmitter. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information. Press the menu button until FOB UNLOCK ON 1ST PRESS appears on the DIC display.
Page 245: Setting The Time
Keeping your mind on the drive is important for safe driving. See Defensive Driving on page 4-2. Here are some ways in which you can help avoid distraction while driving. While your vehicle is parked: • Familiarize yourself with all of its controls. •...
Page 246: Radio(S) (Mp3)
Radio(s) (MP3) Radio with CD shown, Radio with Six-Disc CD similar Your vehicle has one of these radios as its audio system. 3-86 Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information.
Page 247: Playing The Radio
Playing the Radio Top Knob (Power/Volume): Press to turn the system on and off. Turn clockwise or counterclockwise to increase or to decrease the volume. (Information): For RDS, press to change what displays while using RDS. The display options are station name, RDS station frequency, PTY (program type), and the name of the program (if available).
Page 248: Setting Preset Stations
Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped)), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, AM, or XM1 or XM2 (if equipped).
Page 249: Rds And Xm
Adjusting the Speakers (Balance/Fade) (Balance/Fade): To adjust the balance between the right and the left speakers, press until BALANCE displays. Turn to move the sound toward the right or the left speakers. To adjust the fade between the front and the rear speakers, press until FADE displays.
Page 250: Rds Messages
SCAN: Scan the stations within a category by performing the following: 1. Press the CAT button. The last selected category displays. 2. Turn the knob to select the category. 3. Once the desired category is displayed, press and hold either SCAN arrow until a beep sounds and SCAN CATEGORY displays.
Page 251: Radio Messages
If TA displays, press the TRAF button to turn off the traffic announcements. This function does not apply to XM™ Satellite Radio Service. Radio Messages CAL ERR (Calibration Error): The audio system has been calibrated for your vehicle from the factory. If CAL ERR displays, it means that the radio has not been conﬁgured properly for your vehicle and must be returned to your dealer/retailer for service.
Page 252: Playing A Cd (Single Cd Player)
Playing a CD (Single CD Player) Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing. If the ignition or radio is turned off with a CD in the player, it stays in the player.
Page 253 Care of Your CDs If playing a CD-R, the sound quality can be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. Handle them carefully. Store CD-R(s) in their original cases or other protective cases and away from direct sunlight and dust.
Page 254 To eject multiple CDs, do the following: 1. Press and hold eject for two seconds. A beep sounds and EJECT ALL DISCS displays. 2. When REMOVE DISC displays, the CD ejects and can be removed. To stop ejecting the CDs, press the load or the eject button.
Page 255 SCAN : To scan one CD, press and hold either arrow for more than two seconds until SCAN displays and a beep sounds. The radio goes to the next track, plays for 10 seconds, then goes to the next track. Press either arrow again, to stop scanning.
Page 256 SONGLIST FULL displays if more than 20 selections are saved. To play the song list, press the tracks begins to play in the order they were saved. Seek through the song list by using the SEEK arrows. Seeking past the last saved track returns to the ﬁrst saved track.
Page 257 CD Messages CHECK CD: If this message displays and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smoother, the CD should play.
Page 258: Mp3 Format
Using an MP3 MP3 CD-R Disc MP3 Format If you burn your own MP3 disc on a personal computer: • Make sure the MP3 ﬁles are recorded on a CD-R disc. • Do not mix standard audio and MP3 ﬁles on one disc.
Page 259 Empty Directory or Folder If a root directory or a folder exists somewhere in the ﬁle structure that contains only folders/subfolders and no compressed ﬁles directly beneath them, the player advances to the next folder in the ﬁle structure that contains compressed audio ﬁles.
Page 260 File System and Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the ﬁle name without the extension (such as .mp3) as the track name. Track names longer than 32 characters or four pages are shortened.
Page 261: Xm Radio Messages
Press and release the RPT button until REPEAT OFF displays, to turn off repeated play. (Information): Press to display the artist name and album contained in the ID3 tag. XM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696).
Page 262: Parental Control
Navigation/Radio System Your vehicle may have a navigation radio system. The navigation system has built-in features intended to minimize driver distraction. Technology alone, no matter how advanced, can never replace your own judgment. See the Navigation System manual for some tips to help you reduce distractions while driving. Rear Seat Entertainment (RSE) System Vehicles with a Rear Seat Entertainment (RSE) system...
Page 263 Wireless Headphones The RSE system may include two sets of wireless headphones (batteries may be included with the headphone sets). The wireless headphones have an ON/OFF switch, a channel select switch, and a volume control. To use the headphones, turn the ON/OFF switch to ON. An indicator light on the headphones come on.
Page 264: Stereo Rca Jacks
Wired Headphones There is a right and left wired headphone jack. To adjust the volume, do the following: 1. Plug the headphone into the corresponding jack, located behind the video screen, next to the auxiliary jacks. 2. Press the headphone volume control button until Wired Headset Volume displays and the Left wired headphone is highlighted for selection.
Page 265 To use the auxiliary audio and video inputs, connect an external auxiliary device such as a camcorder to the RCA jacks and turn on both the auxiliary device power and the power on the front of the RSE player. If a disc is present when the RSE power is turned on, the player automatically begins playing the disc.
Page 266: Dvd Player
Video Screen The video screen is located in the overhead console. To use the video screen, do the following: 1. Push the release button located on the overhead console. 2. Move the screen to the desired position. When the video screen is not in use, push it up into its locked position.
Page 267 DVD Player Buttons RSE Faceplate with Rear Seat Climate Controls shown, RSE Faceplate without Rear Seat Climate Controls similar (Stop/Eject): Press and release this button to stop playing, rewinding, or fast forwarding. Press this button twice to eject a disc. If the player is already stopped, then only press this button once.
Page 268: Ejecting A Disc
MENU (Disc): Press this button to view the main DVD menu. The menu is different on every disc. Use the up, down, right, and left arrow buttons to move the cursor around the menu. After making a selection, press the enter button.
Page 269: Remote Control
Remote Control The RSE system includes a remote control (batteries may be included with the remote control). To use the remote control, aim it at the transmitter window next to the RSE faceplate and press the desired button. Direct sunlight or very bright light can affect the ability of the transmitter to receive signals from the remote control.
Page 270 (Menu Navigation Arrows): Press the navigation arrows to move through DVD menus. The up and down arrows move through MP3 folders. (Enter): Press this button to select the choice that is highlighted in any menu. (Display Control Button): Press this button to open the RSE On-Screen Display (OSD) menus to adjust the color, tint, brightness, contrast, and display modes.
Page 271 (Subtitles): Press this button to display the current subtitles. Each press of this button moves the DVD to the next available subtitle option (English, Spanish, French, etc., if available). The format and content of this function vary for each disc. AUX (Auxiliary): Press this button to switch the system between the DVD player and an auxiliary source.
Page 272 To use the RSE OSD menu when using a CD or an MP3, do the following: Make sure that a CD or an MP3 is loaded in the RSE system and that the system is not in auxiliary, then press button on the remote control, or faceplate if there is no rear seat climate control.
Page 273 Tips and Troubleshooting Chart (cont’d) Problem Recommended Action No sound — Wireless Turn the headphones on. Headphones Make sure the correct channel is selected on the wireless headphones. Check the batteries. The volume on the headphones could be too low, adjust the volume. No sound —...
Page 274 Tips and Troubleshooting Chart (cont’d) Problem Recommended Action The remote control does Point the remote control not work. directly at the face of the DVD unit. The batteries could be weak or put in wrong. The parental control button might have been pressed, the power indicator lights ﬂash.
Page 275 Tips and Troubleshooting Chart (cont’d) Problem Recommended Action DVD System inoperable. In severe or extreme temperatures the DVD system might not be operable. Temperatures below −4°F (−20°C) or above 140°F (60°C) could damage the DVD system. Operate the DVD system under normal or comfortable cabin temperature ranges.
Page 276: Dvd Distortion
DVD Display Error Messages The following errors could display on the video screen. Disc Format Error: This message displays if a disc is inserted upside down, if the disc is not readable, or if the disc format is not compatible. Disc Play Error: This message displays if the mechanism cannot play the disc.
Page 277: Rear Seat Audio (Rsa)
Rear Seat Audio (RSA) Vehicles with a rear seat audio (RSA) system allows rear seat passengers to listen to and control any of the following audio sources: AM/FM tuner, front CD player, and XM™ Satellite Radio Service (if equipped). However, the rear seat passengers can only control the sources that the front seat passengers are not listening to.
Page 278: Theft-Deterrent Feature
Left Arrow – Press the left arrow while in AM/FM tuner, or XM™ Satellite Radio Service to seek down. Press the left arrow while sourcing the single CD player, or the six-disc CD player to go to the previous track. Right Arrow –...
Page 279: Audio Steering Wheel Controls
Audio Steering Wheel Controls If your vehicle has this feature, some audio controls can be adjusted at the steering wheel. They include the following: wt u x (Seek/Scan): Press the seek arrows to go to the previous or the next station and stay there. To scan stations, press and hold either scan arrow for two seconds until FREQUENCY SCAN displays.
Page 280: Radio Reception
Radio Reception Frequency interference and static during normal radio reception can occur if items such as cellphone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Page 281: Fixed Mast Antenna
Fixed Mast Antenna The ﬁxed mast antenna can withstand most car washes without being damaged. If the mast should ever become slightly bent, straighten it out by hand. If the mast is badly bent, replace it. Check occasionally to make sure the mast is still tightened to the antenna base.
Page 282 NOTES 3-122...
Page 283: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-3 Control of a Vehicle ...4-4 Braking ...4-4 Antilock Brake System (ABS) ...4-5 Braking in Emergencies ...4-6 Traction Control System (TCS) ...4-6 ® StabiliTrak System ...4-7 Steering ...4-9 Off-Road Recovery ...4-11 Passing ...4-12...
Page 284: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving Defensive driving means “always expect the unexpected.” The ﬁrst step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 1-23. CAUTION: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
Page 285: Drunk Driving
Drunk Driving CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking.
Page 286: Control Of A Vehicle
Control of a Vehicle The following three systems help to control your vehicle while driving — brakes, steering, and accelerator. At times, as when driving on snow or ice, it is easy to ask more of those control systems than the tires and road can provide.
Page 287: Antilock Brake System (Abs)
Antilock Brake System (ABS) Your vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that will help prevent a braking skid. When you start the engine and begin to drive away, ABS will check itself. You might hear a momentary motor or clicking noise while this test is going on, and you might even notice that the brake pedal moves or pulses a little.
Page 288: Braking In Emergencies
Braking in Emergencies With ABS, you can steer and brake at the same time. In many emergencies, steering can help you more than even the very best braking. Traction Control System (TCS) Your vehicle may have a traction control system that limits wheel spin.
Page 289: Stabilitrak ® System
To turn the system off, press the traction control button located on the center of the instrument panel. If the system is limiting wheel spin when you press the button, the TRACTION CONTROL ACTIVE message will go off, but the system will not turn off until there is no longer a current need to limit wheel spin.
Page 290: Traction Control Operation
The STABILITY CONTROL ACTIVE message will appear on the DIC only when the system is both on and activated. It means that an advanced computer-controlled system has come on to help your vehicle continue to go in the direction in which you ®...
Page 291: Steering
The traction control system may activate on dry or rough roads or under conditions such as heavy acceleration while turning or abrupt upshifts/downshifts of the transaxle. When this happens you may notice a reduction in acceleration, or may hear a noise or vibration.
Page 292: Steering In Emergencies
What should you do if this ever happens? Ease up on the brake or accelerator pedal, steer the vehicle the way you want it to go, and slow down. Speed limit signs near curves warn that you should adjust your speed. Of course, the posted speeds are based on good weather and road conditions.
Page 293: Off-Road Recovery
An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Page 294: Passing
Passing Passing another vehicle on a two-lane road can be dangerous. To reduce the risk of danger while passing, we suggest the following tips: • Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait.
Page 295: Driving At Night
Of course, traction is reduced when water, snow, ice, gravel, or other material is on the road. For safety, you will want to slow down and adjust your driving to these conditions. It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited.
Page 296: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or ﬂowing water. CAUTION: Wet brakes can cause accidents.
Page 297: Before Leaving On A Long Trip
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? •...
Page 298: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: • Keep your vehicle serviced and in good shape. • Check all ﬂuid levels and brakes, tires, cooling system, and transmission.
Page 299: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You might want to put winter emergency supplies in your vehicle. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning triangles.
Page 300: If You Are Caught In A Blizzard
If your vehicle has a traction system, it will improve your ability to accelerate when driving on a slippery road. But you can turn the traction system off if you ever need to. You should turn the traction system off if your vehicle ever gets stuck in sand, mud, ice, or snow.
Page 301 You can run the engine to keep warm, but be careful. CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 302: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 303: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. See Traction Control System (TCS) on page 4-6 and StabiliTrak page 4-7.
Page 304 Tire and Loading Information Label Example Label A vehicle speciﬁc Tire and Loading Information label is attached to the center pillar (B-pillar) of your vehicle. With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms...
Page 305 Steps for Determining Correct Load Limit Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 306 Example 2 Item Description Vehicle Capacity Weight for Example 2 = Subtract Occupant Weight 150 lbs (68 kg) × 5 = Available Cargo Weight = 4-24 Total Item 1,000 lbs (453 kg) 750 lbs (340 kg) 250 lbs (113 kg) Example 3 Description Vehicle Capacity...
Page 307 Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight. Certiﬁcation/Tire Label A vehicle speciﬁc Certiﬁcation/Tire label is attached to the rear edge of the driver’s door.
Page 308 Never exceed the GVWR for your vehicle or the GAWR for either the front or rear axle. CAUTION: Do not load your vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR).
Page 309: Towing
Towing Towing Your Vehicle Consult your dealer/retailer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-6. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing”...
Page 310: Level Control
Level Control On vehicles equipped with automatic level control, the rear of the vehicle is automatically kept level as you load or unload your vehicle. However, you should still not exceed the GVWR or the GAWR. See Loading Your Vehicle on page 4-21. You may hear the compressor operating when you load or unload your vehicle, and periodically as the system self-adjusts.
Page 311: If You Do Decide To Pull A Trailer
Your vehicle can tow a trailer. To identify the trailering capacity of vehicle, you should read the information in “Weight of the Trailer” that appears later in this section. Trailering is different than just driving your vehicle by itself. Trailering means changes in handling, acceleration, braking, durability, and fuel economy.
Page 312: Weight Of The Trailer
Weight of the Trailer How heavy can a trailer safely be? It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature, and how much your vehicle is used to pull a trailer are all important. It can also depend on any special equipment that you have on your vehicle, and the amount of tongue weight the vehicle can carry.
Page 313: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 314 Consider the following example: A vehicle model base weight is 5,500 lbs (2 495 kg); 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs (1 225 kg) at the rear axle. It has a GVWR of 7,200 lbs (3 266 kg), a RGAWR of 4,000 lbs (1 814 kg) and a GCWR (Gross Combination Weight Rating) of 14,000 lbs (6 350 kg).
Page 315: Safety Chains
It is important that you make sure your vehicle does not exceed any of its ratings — GCWR, GVWR, RGAWR, Maximum Trailer Rating or Tongue Weight. The only way to be sure you are not exceeding any of these ratings is to weigh your vehicle and trailer. Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires.
Page 316: Driving With A Trailer
Driving with a Trailer CAUTION: If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You cannot see or smell CO. It can cause unconsciousness or death. See Engine Exhaust on page 2-41.
Page 317: Making Turns
Towing a trailer requires a certain amount of experience. Before setting out for the open road, you will want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself.
Page 318: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer When you tow a trailer, your vehicle has to have extra wiring. The arrows on your instrument panel will ﬂash whenever you signal a turn or lane change. Properly hooked up, the trailer lamps will also ﬂash, telling other drivers you are about to turn, change lanes, or stop.
Page 319: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you do the following: • Start your engine. • Shift into a gear. • Release the parking brake. 2.
Page 320 NOTES 4-38...
Page 321: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-3 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of Your Vehicle ...5-4 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-5 California Fuel ...5-5 Additives ...5-6 Fuel E85 (85% Ethanol) ...5-6...
Page 322 Section 5 Tire Inspection and Rotation ...5-62 When It Is Time for New Tires ...5-64 Buying New Tires ...5-65 Different Size Tires and Wheels ...5-66 Uniform Tire Quality Grading ...5-67 Wheel Alignment and Tire Balance ...5-68 Wheel Replacement ...5-68 Tire Chains ...5-70 Accessory Inﬂator ...5-70 If a Tire Goes Flat ...5-72 Changing a Flat Tire ...5-73...
Page 323: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to your vehicle they can affect your vehicle’s performance and safety, including such things as, airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like...
Page 324: California Perchlorate Materials Requirements
California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless entry transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/perchlorate. Doing Your Own Service Work CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a...
Page 325: Fuel
Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. The 8th digit of the Vehicle Identiﬁcation Number (VIN) shows the code letter or number that identiﬁes your vehicle’s engine.
Page 326: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S.
Page 327: Fuels In Foreign Countries
Many service stations will not have an 85% ethanol fuel (E85) pump available. The U. S. Department of Energy has an alternative fuels website (www.eere.energy.gov/afdc/infrastructure/locator.html) that can help you ﬁnd E85 fuel. Those stations that do have E85 should have a label indicating ethanol content.
Page 328: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 329 CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Page 330: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 331: Hood Release
Hood Release To open the hood, do the following: 1. Pull the hood release handle with this symbol on it. It is located under the instrument panel on the driver’s side. 2. Go to the front of the vehicle and push the underhood release to the right.
Page 332: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.9L V6 engine, here is what you will see: 5-12...
Page 333: Engine Oil
A. Underhood Fuse Block. See Underhood Fuse Block on page 5-102. B. Remote Positive (+) Terminal. See Jump Starting on page 5-37. C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-32. D. Radiator Pressure Cap. See Radiator Pressure Cap on page 5-24.
Page 334: When To Add Engine Oil
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-105.
Page 335: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for three things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. Look for and use only an oil that meets GM Standard GM6094M. • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle.
Page 336: Engine Oil Life System
If you are in an area of extreme cold, where the temperature falls below −20°F (−29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil. Both provide easier cold starting and better protection for the engine at extremely low temperatures.
Page 337: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change the oil prior to a CHANGE OIL SOON message being turned on, reset the system.
Page 338: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-12 for the location of the engine air cleaner/ﬁlter. 5-18 When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after each 50,000 mile (85 000 km) interval.
Page 339 To inspect or replace the air cleaner/ﬁlter, do the following: 1. Remove the two clamps on the duct. 2. Remove the duct. 3. Unlatch the two hooks on top of the engine air cleaner/ﬁlter housing. 4. Inspect or replace the engine air cleaner/ﬁlter. 5.
Page 340: Automatic Transmission Fluid
Automatic Transmission Fluid When to Check and Change Automatic Transmission Fluid A good time to check your automatic transmission ﬂuid level is when the engine oil is changed. Change the ﬂuid and ﬁlter at the intervals listed in Additional Required Services on page 6-6, and be sure to use the transmission ﬂuid listed in Recommended Fluids and Lubricants on page 6-11.
Page 341: How To Add Automatic Transmission Fluid
Checking the Fluid Level Prepare your vehicle as follows: 1. Park your vehicle on a level place. Keep the engine running. 2. With the parking brake applied, place the shift lever in PARK (P). 3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range.
Page 342: Engine Coolant
Engine Coolant The cooling system in your vehicle is ﬁlled with ® DEX-COOL engine coolant. This coolant is designed to remain in your vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst, if you add only ®...
Page 343: Checking Coolant
If you have to add coolant more than four times a year, have your dealer/retailer check your cooling system. Notice: If you use extra inhibitors and/or additives in your vehicle’s cooling system, you could damage your vehicle. Use only the proper mixture of the engine coolant listed in this manual for the cooling system.
Page 344: Radiator Pressure Cap
Occasionally check the coolant level in the radiator. For information on how to add coolant to the radiator, see Cooling System on page 5-26. Radiator Pressure Cap Notice: The radiator cap on your vehicle is a pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating.
Page 345: If No Steam Is Coming From Your Engine
If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: • Climb a long hill on a hot day.
Page 346: Cooling System
Cooling System When you decide it is safe to lift the hood, here is what you will see: A. Radiator C. Engine Coolant Pressure Cap Recovery Tank B. Electric Engine D. Recovery tank Cooling Fans FULL COLD mark 5-26 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
Page 347 CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ﬁre, and you could be burned.
Page 348 How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet, but the coolant level is not at or above the full cold mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL engine coolant at the coolant recovery tank.
Page 349: How To Add Coolant To The Radiator
If the overheat warning continues, there is one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the cooling system is cool before you do it. CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
Page 350 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. 3. Fill the radiator with the proper DEX-COOL coolant mixture, up to the base of the ﬁller neck.
Page 351: Power Steering Fluid
Power Steering Fluid The power steering ﬂuid reservoir is located toward the rear of the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise.
Page 352: Windshield Washer Fluid
Windshield Washer Fluid What Washer Fluid to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing.
Page 353: Brakes
Brakes Brake Fluid The brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear.
Page 354 What to Add When you need brake ﬂuid, use only DOT-3 brake ﬂuid. Use new brake ﬂuid from a sealed container only. See Recommended Fluids and Lubricants on page 6-11. Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Page 355: Brake Wear
Brake Wear Your vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.
Page 356: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality brake parts. When you replace parts of the braking system —...
Page 357: Jump Starting
Jump Starting If your vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. On vehicles equipped with the optional power sliding door, a low-voltage battery or replacing a battery may cause the system to become inoperative.
Page 358 Notice: If you leave your radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty. Always turn off your radio and other accessories when jump starting your vehicle. 3.
Page 359 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 360 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery.
Page 361: Headlamp Aiming
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3.
Page 362: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-46. For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 363 To replace one of these bulbs: 1. Open the hood. See Hood Release on page 5-11 for more information. 2. Remove the headlamp retainer pin (A) by turning it towards the headlamp assembly and pulling it straight out. 3. Remove the screw (B) from the top of the headlamp assembly.
Page 364: Front Turn Signal, Parking And Daytime Running Lamps (Drl)
Front Turn Signal, Parking and Daytime Running Lamps (DRL) To replace one of these bulbs (A): 1. Follow the Steps 1 through 4 to remove the headlamp assembly. See Headlamps and Sidemarker Lamps on page 5-42 for more information. 2. Turn the bulb socket counterclockwise to remove from the assembly.
Page 365 A. Stoplamp/Taillamp B. Turn Signal Lamp C. Back-up Lamp Bulb 5. Turn the bulb socket counterclockwise to remove. 6. Replace the bulb by pulling the old bulb out of the socket and gently pushing in a new bulb. 7. Replace the bulb socket by inserting and turning clockwise to secure.
Page 366: License Plate Lamp
License Plate Lamp To replace one of these bulbs: 1. Remove the two screws holding each of the license plate lamps to the fascia. 2. Turn and pull the license plate lamp forward through the fascia opening. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Page 367: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Normal Maintenance Replacement Parts on page 6-13.
Page 368: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. CAUTION: • Poorly maintained and improperly used tires are dangerous.
Page 369: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 370 (F) Uniform Tire Quality Grading (UTQG) Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 5-67. (G) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load.
Page 371 (F) Tire Size A combination of letters and numbers deﬁne a tire’s width, height, aspect ratio, construction type, and service description. The letter T as the ﬁrst character in the tire size means the tire is for temporary use only. (G) TPC Spec (Tire Performance Criteria Speciﬁcation) Original equipment tires designed...
Page 372: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight This means the combined weight of optional accessories.
Page 373 Load Index An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inﬂation Pressure pressure to which a cold tire can be inﬂated. The maximum air pressure is molded onto the sidewall.
Page 374: Inﬂation - Tire Pressure
Treadwear Indicators Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1/16 inch (1.6 mm) of tread remains. See When It Is Time for New Tires on page 5-64. UTQGS (Uniform Tire Quality Grading Standards) A tire information system that provides consumers with ratings for a tire’s...
Page 375 A vehicle speciﬁc Tire and Loading Information label is attached to your vehicle. This label shows your vehicle’s original equipment tires and the correct inﬂation pressures for your tires when they are cold. The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity.
Page 376: High-Speed Operation
High-Speed Operation CAUTION: Driving at high speeds, 100 mph (160 km/h) or higher, puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. You could have a crash and you or others could be killed.
Page 377: Tire Pressure Monitor System
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inﬂated to the inﬂation pressure recommended by the vehicle manufacturer...
Page 378: Tire Pressure Monitor Operation
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Page 379 At the same time a message to check the pressure in a speciﬁc tire appears on the Driver Information Center (DIC) display. The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inﬂated to the correct inﬂation pressure.
Page 380: Tpms Malfunction Light And Message
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light ﬂashes for about one minute and then stays on for the remainder of the ignition cycle.
Page 381: Tpms Sensor Matching Process
TPMS Sensor Matching Process Each TPMS sensor has a unique identiﬁcation code. Any time you rotate your vehicle’s tires or replace one or more of the TPMS sensors, the identiﬁcation codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver...
Page 382: Tire Inspection And Rotation
6. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire’s air pressure for ﬁve seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, conﬁrms that the sensor identiﬁcation code has been matched to this tire and wheel position.
Page 383 When rotating your vehicle’s tires, always use the correct rotation pattern shown here. Do not include the compact spare tire in the tire rotation. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label. See Inﬂation - Tire Pressure on page 5-54 and Loading Your Vehicle on page 4-21.
Page 384: When It Is Time For New Tires
When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions inﬂuence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch...
Page 385: Buying New Tires
Buying New Tires GM has developed and matched speciﬁc tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Speciﬁcation (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
Page 386: Different Size Tires And Wheels
CAUTION: If you use bias-ply tires on your vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle. If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and...
Page 387: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance.
Page 388: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 389: Used Replacement Wheels
If you need to replace any of your wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, wheel nuts, and TPMS sensors for your vehicle.
Page 390: Tire Chains
Tire Chains CAUTION: Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash.
Page 391 There may be an accessory inﬂator kit stored in the rear compartment on the passenger’s side. It includes a 20-foot (6 m) hose with an air pressure gage and nozzle adapters. CAUTION: Inﬂating something too much can make it explode, and you or others could be injured. Be sure to read the inﬂator instructions, and inﬂate any object only to its recommended pressure.
Page 392: If A Tire Goes Flat
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Page 393: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your vehicle’s hazard warning ﬂashers. See Hazard Warning Flashers on page 3-6 for more information. CAUTION: Changing a tire can be dangerous.
Page 394: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The tools needed to remove the spare tire are located in the storage compartment at the rear of the vehicle, on the passenger’s side. 5-74 To remove the tools: 1. Open the liftgate. See Liftgate on page 2-22 for more information.
Page 395 5. Separate the plastic pouch from the jack and remove the jacking tools, including the folding wrench and extension, from the pouch. The tools you will be using include the jack (A), extension (B), and folding wrench (C). The compact spare tire is located under the rear of the vehicle.
Page 396: Removing The Flat Tire And Installing The Spare Tire
3. Tilt the retainer at the end of the cable to remove the compact spare tire, so it can be pulled up through the wheel opening. The hoist is used to store a full-size or a ﬂat road tire under the vehicle. See Storing a Flat or Spare Tire and Tools on page 5-86 for more information.
Page 397 Store the wheel cover securely in the rear of the vehicle until you have the ﬂat tire repaired or replaced. Once the wheel cover has been removed, use the following procedure to remove the ﬂat tire and install the spare tire. 1.
Page 398 A. Front Location B. Rear Location Notice: If your vehicle has wheel locks and an impact wrench is used to remove the wheel nuts, the lock nut or wheel lock key could be damaged. Do not use an impact wrench to remove the wheel nuts if your vehicle has wheel locks.
Page 399 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Page 400 6. Raise the vehicle by turning the folding wrench clockwise in the jack. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to ﬁt under the wheel well. 7. Remove all the wheel nuts and take off the ﬂat tire. 5-80 CAUTION: Rust or dirt on a wheel, or on the parts to...
Page 401 CAUTION: Never use oil or grease on studs or nuts. Because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash. 8. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. 9.
Page 402 10. Lower the vehicle by attaching the folding wheel wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. 5-82 CAUTION: Incorrect or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to a crash. If you have to replace them, be sure to get new original equipment wheel nuts.
Page 403: Secondary Latch System
11. Tighten the wheel nuts ﬁrmly in a crisscross sequence, as shown. Notice: Wheel covers will not ﬁt on your vehicle’s compact spare. If you try to put a wheel cover on the compact spare, the cover or the spare could be damaged.
Page 404 CAUTION: Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely, make sure no one is behind you or on either side of you as you pull the jack out from the under spare.
Page 405 2. Turn the folding wrench clockwise to raise the jack until it lifts the secondary latch device under the wheel plate. 3. Keep raising the jack until the compact spare tire stops moving upward and is held ﬁrmly in place. This lets you know that the secondary latch has released.
Page 406: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. 5-86 Storing the Flat or Spare Tire CAUTION:...
Page 407 To store the spare tire: 1. Lay the tire near the rear of the vehicle with the valve stem down. 2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels.
Page 408 Storing the Tools A. Strap B. Bag and Tools C. Jack 5-88 Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on. To replace the cover, line up the tabs on the right of the cover with the slots in the cover opening.
Page 409: Compact Spare Tire
Compact Spare Tire Although the compact spare tire was fully inﬂated when the vehicle was new, it can lose air after a time. Check the inﬂation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inﬂated.
Page 410: Appearance Care
Appearance Care Interior Cleaning Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery.
Page 411: Fabric/Carpet
• Use only mild, neutral-pH soaps. Avoid laundry detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.
Page 412: Leather
Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry.
Page 413: Care Of Safety Belts And Built-In Child Restraint Harness
Care of Safety Belts and Built-in Child Restraint Harness Keep the safety belts and the built-in child restraint harness clean and dry. CAUTION: Do not bleach or dye safety belts or the built-in child restraint harness. If you do, they may be severely weakened.
Page 414: Cleaning Exterior Lamps/Lenses
High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle. Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses.
Page 415: Windshield, Backglass, And Wiper Blades
Windshield, Backglass, and Wiper Blades Clean the outside of the windshield and backglass with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer ﬂuid or a mild detergent. Wash the windshield thoroughly when you clean the blades.
Page 416: Tires
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Page 417: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Description Interior and exterior Polishing Cloth polishing cloth. Tar and Road Removes tar, road oil, Oil Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel. Removes soil and black White Sidewall marks from whitewalls Tire Cleaner and raised white lettering.
Page 418: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. You can see it if you look through the windshield from outside your vehicle.
Page 419: Electrical System
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to your vehicle unless you check with your dealer/retailer ﬁrst. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 420: Fuses And Circuit Breakers
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of ﬁres caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.
Page 421 Fuses Usage Trunk, Door Locks Electronic Level Control Rear Wiper Radio, DVD Player Interior Lamps ® OnStar Keyless Entry Module Cluster, Heating, Ventilation, Air Conditioning Cruise Switch Steering Wheel Illumination Power Mirror Stoplamp, Turn Lamps Heated Seats Blank Electronic Level Control Heated Mirror Center High-Mounted Stoplamp, Back-up Lamps...
Page 422: Underhood Fuse Block
Underhood Fuse Block The underhood fuse block is located in the engine compartment. For more information on location see Engine Compartment Overview on page 5-12. Notice: Spilling liquid on any electrical components on your vehicle may damage it. Always keep the covers on any electrical component.
Page 423 Fuses Usage Right High-Beam Fuel Pump Diode BLANK Not Used BLANK Not Used Left High-Beam BLANK Not Used BLANK Not Used BLANK Not Used Not Used Air Conditioning Clutch Horn Left Low-Beam Powertrain Control Module, Electronic Throttle Control Not Used Transmission Solenoid Right Low-Beam Fuses...
Page 424 J-Case Fuses Fuse Puller Fan 1 Starter Solenoid Antilock Brake System Motor Blank Fan 2 Front Blower High Battery Main 3 Rear Defogger Battery Main 2 Spare 5-104 Usage Relays RUN RLY LO BEAM FUEL PUMP AC/CLTCH HI BEAM PWR/TRN IGN MAIN BLANK Usage...
Page 425: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric measurements. See Recommended Fluids and Lubricants on page 6-11 for more information. Application Air Conditioning Refrigerant R134a Automatic Transaxle — Pan Removal and Replacement Cooling System 3.9L Engine Front Climate Controls Only 3.9L Engine with Rear Climate Controls Engine Oil with Filter Fuel Capacity...
Page 426 NOTES 5-106...
Page 427 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-11...
Page 428: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer/retailer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 429 This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will ﬁnd these limits on the Tire and Loading Information label. See Loading Your Vehicle on page 4-21. • are driven on reasonable road surfaces within legal driving limits.
Page 430: Scheduled Maintenance
Scheduled Maintenance When the CHANGE OIL SOON message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 431 Change engine oil and ﬁlter. See Engine Oil on page 5-13. Reset oil life system. See Engine Oil Life System on page 5-16. An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage. See footnote (k). Inspect engine air cleaner ﬁlter.
Page 432: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 433: Maintenance Footnotes
Maintenance Footnotes # Lubricate the suspension, steering linkage, and the underbody contact points and linkage. (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc. Inspect disc brake pads for wear and rotors for surface condition.
Page 434: Owner Checks And Services
(h) Change automatic transmission ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 435: At Least Once A Month
Engine Coolant Level Check Check the engine coolant level and add DEX-COOL coolant mixture if necessary. See Engine Coolant on page 5-22. Windshield Washer Fluid Level Check Check the windshield washer ﬂuid level in the windshield washer ﬂuid reservoir and add the proper ﬂuid if necessary.
Page 436 Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
Page 437: Recommended Fluids And Lubricants
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. • To check the parking brake’s holding ability: With the engine running and the transmission in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal.
Page 438 Usage Fluid/Lubricant Windshield ® Optikleen Washer Solvent. Washer GM Power Steering Fluid Power Steering (GM Part No. U.S. 89021184, System in Canada 89021186). ® Automatic DEXRON -VI Automatic Transmission Transmission Fluid. Multi-Purpose Lubricant, Superlube Key Lock (GM Part No. U.S. 12346241, Cylinders in Canada 10953474).
Page 439: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter Engine Oil Filter Spark Plugs Windshield Wiper Blades Driver’s Side — 22.0 inches (55.0 cm) Passenger’s Side — 24.0 inches (60.0 cm) Rear —...
Page 440: Engine Drive Belt Routing
Engine Drive Belt Routing 3.9L V6 Engine and 3.9L V6 Flexible Fuel 6-14...
Page 441: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Page 442 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 443 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 444 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 445: Customer Assistance Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-4 Customer Assistance for Text Telephone (TTY) Users ...7-5 Customer Assistance Offices ...7-5 GM Mobility Reimbursement Program ...7-6 Roadside Assistance Program ...7-6 Scheduling Service Appointments ...7-9 Courtesy Transportation ...7-9 Collision Damage Repair ...7-11 Customer Assistance Information...
Page 446: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 447 Although you may be required to resort to this informal dispute resolution program prior to ﬁling a court action, use of the program is free of charge and your case will generally be heard within 40 days. If you do not agree with the decision given in your case, you may reject it and proceed with any other venue for relief available to you.
Page 448: Online Owner Center
Online Owner Center Online Owner Center (United States only) The Owner Center is a resource for your GM ownership needs. Speciﬁc vehicle information can be found in one place. The Online Owner Center allows you to: • Get e-mail service reminders. •...
Page 449: Customer Assistance For Text Telephone (Tty) Users
(2438). (TTY users in Canada can dial 1-800-263-3830.) Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Chevrolet, the letter should be addressed to: United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 450: Gm Mobility Reimbursement Program
(Text telephone (TTY): 1-888-889-2438). For vehicles purchased in Canada, call 1-800-268-6800. Service is available 24 hours a day, 365 days a year. As the owner of a new Chevrolet vehicle, you are automatically enrolled in the Chevrolet Roadside Assistance program.
Page 451 Services Provided The following services are provided in the U.S. and Canada up to 5 years/100,000 miles (160 000 km), whichever occurs ﬁrst, and, in Canada only, up to a maximum coverage of $100. • Fuel Delivery: Delivery of enough fuel for the vehicle to get to the nearest service station (approximately $5 in Canada).
Page 452 However, any cost for parts and labor for non-warranty repairs are the responsibility of the driver. Chevrolet and General Motors of Canada Limited reserve the right to limit services or reimbursement to an owner or driver when, in their sole discretion, the claims become excessive in frequency or type of occurrence.
Page 453: Scheduling Service Appointments
Roadside Assistance is not part of or included in the coverage provided by the New Vehicle Limited Warranty. Chevrolet and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 454: Transportation Options
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Shuttle service is the preferred means of offering Courtesy Transportation.
Page 455: Collision Damage Repair
Additional Program Information All program options, such as shuttle service, may not be available at every dealer. Please contact your dealer for speciﬁc information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel. General Motors reserves the right to unilaterally modify, change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described...
Page 456: If A Crash Occurs
Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comparable equipment.
Page 457 • Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identiﬁcation Number (VIN), insurance company and policy number, and a general description of the damage to the other vehicle.
Page 458: Reporting Safety Defects
In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P.O. Box 33170 Detroit, MI 48232-5170 In Canada, call 1-800-263-3777 (English) or...
Page 459: Service Publications Ordering Information
Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins’ give additional technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle.
Page 460: Vehicle Data Recording And Privacy
Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
Page 461: Onstar
GM will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an official request of police or similar government office;...
Page 462 NOTES 7-18...
Page 463 Accessories and Modiﬁcations ... 5-3 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-90 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-99 Air Cleaner/Filter, Engine ... 5-18 Air Conditioning ... 3-24, 3-27 Airbag Passenger Status Indicator ... 3-38 Readiness Light ... 3-37 Airbag System ...
Page 464 Audio System (cont.) Navigation/Radio System, see Navigation Manual ... 3-102 Radio Reception ... 3-120 Rear Seat Audio (RSA) ... 3-117 Setting the Time ... 3-85 Theft-Deterrent Feature ... 3-118 XM™ Satellite Radio Antenna System ... 3-121 Audio System(s) ... 3-86 Automatic Door Lock ...
Page 465 Check Engine Light ... 3-44 Checking Things Under the Hood ... 5-10 Chemical Paint Spotting ... 5-96 Child Restraints Built-In Child Restraint ... 1-68 Child Restraint Systems ... 1-49 Infants and Young Children ... 1-46 Lower Anchors and Tethers for Children ... 1-53 Older Children ...
Page 466 Customer Assistance Information (cont.) Reporting Safety Defects to General Motors ... 7-14 Reporting Safety Defects to the Canadian Government ... 7-14 Reporting Safety Defects to the United States Government ... 7-14 Roadside Assistance Program ... 7-6 Service Publications Ordering Information ... 7-15 Daytime Running Lamps/Automatic Headlamp System ...
Page 467 Engine Air Cleaner/Filter ... 5-18 Check and Service Engine Soon Light ... 3-44 Coolant ... 5-22 Coolant Heater ... 2-34 Coolant Temperature Gage ... 3-43 Drive Belt Routing ... 6-14 Engine Compartment Overview ... 5-12 Exhaust ... 2-41 Oil ... 5-13 Oil Life System ...
Page 468 Gage Engine Coolant Temperature ... 3-43 Fuel ... 3-49 Speedometer ... 3-36 Tachometer ... 3-36 Garage Door Opener ... 2-51 Gasoline Octane ... 5-5 Speciﬁcations ... 5-5 Glove Box ... 2-56 GM Mobility Reimbursement Program ... 7-6 Hazard Warning Flashers ... 3-6 Head Restraints ...
Page 469 Jump Starting ... 5-37 Keyless Entry System ... 2-4 Keys ... 2-3 Labeling, Tire Sidewall ... 5-49 Lamps Cargo ... 3-19 Dome ... 3-18 Front Reading ... 3-19 Rear Reading ... 3-19 Lap-Shoulder Belt ... 1-36 LATCH System Child Restraints ... 1-53 Level Control ...
Page 470 Locks (cont.) Loss of Control ... 4-12 Low Fuel Warning Light ... 3-49 Luggage Carrier ... 2-60 Maintenance Schedule Additional Required Services ... 6-6 At Each Fuel Fill ... 6-8 At Least Once a Month ... 6-9 At Least Once a Year ... 6-9 Introduction ...
Page 471 ® ® OnStar System, see OnStar Manual ... 2-47 Operation, Universal Home Remote System ... 2-51 Other Warning Devices ... 3-6 Outlet Adjustment ... 3-30 Outlets Accessory Power ... 3-22 Outside Convex Mirror ... 2-44 Heated Mirrors ... 2-44 Power Mirrors ... 2-43 Overhead Console ...
Page 472 Radiator Pressure Cap ... 5-24 Radio Frequency Identiﬁcation (RFID), Privacy ... 7-17 Radios ... 3-84 Radio(s) ... 3-86 Radios Navigation/Radio System, see Navigation Manual ... 3-102 Rear Seat Audio ... 3-117 Reception ... 3-120 Setting the Time ... 3-85 Theft-Deterrent ... 3-118 Rear Climate Control System ...
Page 473 Safety Belts (cont.) Safety Belt Use During Pregnancy ... 1-41 Safety Belts Are for Everyone ... 1-23 Safety Warnings and Symbols ... iii Scheduled Maintenance ... 6-4 Seats Bucket Seats, Rear ... 1-6 Captain Chairs ... 1-14 Head Restraints ... 1-6 Heated Seats ...
Page 474 Steering Wheel Controls, Audio ... 3-119 Steering Wheel, Tilt Wheel ... 3-6 Storage Areas ... 2-56 Convenience Center ... 2-62 Convenience Net ... 2-61 Cupholder(s) ... 2-56 Floor Console Storage Area ... 2-59 Folding Tray ... 2-59 Glove Box ... 2-56 Luggage Carrier ...
Page 475 Tires (cont.) Storing a Flat or Spare Tire and Tools ... 5-86 Tire Sidewall Labeling ... 5-49 Tire Terminology and Deﬁnitions ... 5-52 Uniform Tire Quality Grading ... 5-67 Wheel Alignment and Tire Balance ... 5-68 Wheel Replacement ... 5-68 When It Is Time for New Tires ...
Page 476 Warning Lights, Gages and Indicators ... 3-34 Warnings DIC Warnings and Messages ... 3-58 Hazard Warning Flashers ... 3-6 Other Warning Devices ... 3-6 Safety and Symbols ... iii Vehicle Damage ... iv Wheels Alignment and Tire Balance ... 5-68 Different Size ...

Chevrolet 2008 Uplander Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Object Detection Systems

Onstar System

Universal Home Remote System

Storage Areas

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Chevrolet 2008 Uplander

Summary of Contents for Chevrolet 2008 Uplander