Ethernet Setup; Proceed To - Crestron Touch the PC v1 Programmer's Manual

Crestron Serial Mouse Control Driver
ETHERNET COMMUNICATION #2 - TILT TOUCHPANEL WITH TPS-XVGA-BV CARD
REF
DEVICE
1
A
2
B
TPS-IMC-BV
3
C
4
D
Control System
4
E
Ethernet / Hub
5
F
PWR. PACK
2
G
TPS-IMC-BV
Standard stranded VGA monitor cable.
1
2 These connections (ref B & G) can be made with the 15-foot Triamese cable supplied with the TPS-IMC-BV. For
further information about the Triamese cable and other cabling options, refer to Appendix 3 on page 25 of this guide.
Standard null modem serial cable.
3
Standard Ethernet cables (ref D & E).
4
Power pack is NOT required if control system is connected to touchpanel via Ethernet AND Cresnet.
5
Ethernet Communication #3 - Lectern Touchpanel with TPS-XVGAL
VGA
PORT
PC
ETHERNET COMMUNICATION #3 - LECTERN TOUCHPANEL WITH TPS-XVGAL CARD
REF
1
A
2
B
3
C
Control System
4
D
Control System
4
E
Ethernet / Hub
A standard stranded VGA monitor cable with DB15F to BNC-5 adapter is required. Both are commercially available.
1
Standard null modem serial cable.
2
3 Cresnet wiring is required for touchpanel operating power only. For Cresnet 4-wire specifications, refer to Appendix
3 on page 25 of this guide.
4 Standard Ethernet cables (ref D &E).

Ethernet Setup

Ethernet devices that are addressed by the control system may have their IP IDs set either in
the SIMPL Windows program or through the Crestron Viewport using a PC. Ultimately, each
IP ID is converted into an actual IP address through an IP table that exists inside the control
system. The IP Table is an internal list of information that contains the IP IDs and associated
IP addresses of all Ethernet devices in the program. The IP Table is accessed by the control
system to identify and locate Ethernet devices, for purposes of communication. Follow this
procedure to add the Serial Control Mouse Driver to the IP table of the touchpanel.
Programmer's Guide - DOC. 5916A
FROM
PORT CONNECTOR
VGA DB-15, male
PC
RGB RJ-45, 10-pin
COM DB-9, female
PC
LAN RJ-45, 8-pin
na RJ-45, 8-pin
na
NET/VIDEO RJ-45, 10-pin
A
RGB CABLE
COMM. CABLE
B
COM
PORT
CREST RON
LAN
PORT
D
ETHERNET
ROUTER/HUB
FROM
DEVICE
PORT CONNECTOR
VGA DB-15, male
PC
COM DB-9, female
PC
NET 4-wire Cresnet
LAN RJ-45, 8-pin
na RJ-45, 8-pin

2. Proceed to

"Ethernet
CABLING REQUIRED
to CONNECTOR
DB-15, male
RJ-45, 10-pin
DB-9, female
RJ-45, 8-pin
RJ-45, 8-pin
na
RJ-45, 10-pin
CONTROL
COM
SYSTEM
PORT
P R OFE SS I ON AL C ONTROL PROC ESSOR MENU
BKLT
2
PRO
NET (OR
CRESNET)
C PORT
ETHERNET
CRESNET WIRING
WIRING
E
CABLING REQUIRED
to CONNECTOR
BNC-5, male
DB-9, female
4-wire Cresnet
RJ-45, 8-pin
RJ-45, 8-pin
Setup" that begins below.
Software
TO
DEVICE PORT
TPS-IMC-BV RGB
Touchpanel RGB
Control System COM
Ethernet / Hub na
Touchpanel LAN
TPS-IMC-BV 24VDC 2A
Touchpanel NET/VIDEO
LECTERN TOUCHPANEL
(OR TPS-TPI) WITH
TPS-XVGAL
RGB
INPUT
TO
PORT
NET
PORT
LAN
PORT
TO
DEVICE PORT
Touchpanel RGB
Control System COM
Touchpanel NET
Ethernet / Hub na
Touchpanel LAN
Serial Mouse Control Driver • 11