Pentair SUNTOUCH Quick Reference Manual

POOL SPA MODE
/
Note: For "SOLAR ONLY" mode setup instructions,
see back page.
1
Press Menu button until Advanced 8/14 displays.
.
2. Press Right button to access Advanced menu.
3. Press Right button until System Mode displays.
4. Press Up/Down button to select Pool/Spa.
5. Press Right or Left button to exit to main screen.
Set Clock (5/14)
Press Menu button until Clock 5/14 is displayed.
1.
2. Press Right button to access Clock menu.
3. Use Right button to select hours/AM,PM and minutes and
Up/Down button adjust time setting.
Press Left button to exit.
4.
Setup Valves (Pool, Spa, AUX) (7/14)
Press Menu button until Valves 7/14 is displayed.
1.
Press Right button to access Valves menu.
2.
Press Up/Down button to select circuit (NONE, SPA, POOL,
3.
AUX 1-3, FEATURE 1-4, SOLAR, HEATER, FREEZE).
4. Press Left button to save and exit.
Circuit Functions/Freeze Protect (10/14)
1. Press Menu button > Right button until Cir. Functions
10/14 is displayed.
2. Press Right button to access Cir. Functions menu.
3. Press Up/Down button to select Freeze Protection
for POOL circuit [Yes/No].
4. Press Right button to select Spa circuit.
5. Press Up/Down button to select Freeze Protection
for SPA Circuit [Yes/No].
6. Press Right button to select AUX 1 Circuit.
7. Press Up/Down button to select function for AUX 1 Circuit
[GENERIC, CLEANER, etc.].
8. Press Right button to select Freeze Protection for AUX 1
Circuit.
9. Press Up/Down button to select Freeze Protection for AUX
1 Circuit [Yes/No].
10. Press Right button and repeat Steps 7-9 for Aux 2 & Aux 3
circuits.
11. Press Left button to exit to main screen.
Pool Circuit Function ON/OFF (1/14)
1. Press Menu > Right button to access Circuit
Off 1/14 menu.
2. Press Up/Down button to turn Pool filter pump ON or OFF.
Pool circuit ON will display Pool temps on screen.
Set Heat Temp/Select Heat Source (2/14)
Press Menu button until Heat 2/14 is displayed.
1.
Press Right button: Displays POOL TEMP, POOL HEAT
2.
(OFF/HEATER), SPA TEMP, SPA HEAT, MANUAL HEAT.
Use Right button to scroll through above options and Up/
3.
Down button to change setting.
4. Press Left button to exit.
Enable Solar/Heat Pump (6/14)
Press Menu button until Solar 6/14 displays.
1.
2. Press Right button to scroll through: Solar Status Enabled
(No/Yes), Heat Start Temp Diff., Heat Stop Diff., Heat
Pump (Yes/No), Cooling (Yes/No), Start Temp, Stop
Temp.
3. Press Up/Down button to change setting.
4. Press Left button to exit.
Air Sensor ON/OFF (8/14)
1. Press Menu button until Advanced 8/14 displays.
2. Press Right button to access Advanced menu.
3. Press Right button to Air Sensor enabled. Press Up/Down
button to disable/enable (NO/YES).
Press Left button to exit to main screen.
4.
SUNTOUCH
Shared Equipment/Single Body
1. Press Menu button until Advanced 8/14 displays.
Press Right button to access Advanced menu.
2.
3. Press Right button to System Type.
4. Press Up/Down button to select Single Body or Shared
Equipment.
Press Left button to exit to main screen.
5.
Schedules (Start/Stop Time) (4/14)
1. Press Menu button > Schedules 4/14 displays.
2. Press Right button to access Schedules menu.
Press Up/Down button to select circuit.
3.
4. Press Right button 3 times to select Program 1/1.
5. Press Right button to set Start Time.
Press Up/Down button to set time (12 hours).
6.
7. Press Right button to set Stop Time.
8. Press Up/Down button to set time (12 hours).
Press Right button to save and exit to main screen.
9.
Edit a Scheduled Program
1. Press Menu button > Schedules 4/14 displays.
Press Right button to access Schedules menu.
2.
3. Press Up/Down button to select circuit to edit.
4. Press Right button to select Program to edit (4/4).
5. Press Up/Down button to select Program (2/4).
Press Right button 2 times to edit Start Time.
6.
7. Press Up/Down button to adjust Start Time.
8. Press Right button to edit Stop Time.
Press Up/Down button to adjust Stop Time.
9.
10. Press Right button to save and exit.
Delete a Scheduled Program
Press Menu button > Schedules 4/14 displays.
1.
2. Press Right button to access Schedules menu.
3. Press Up/Down button to select circuit to delete.
Press Right button to select Program to delete.
4.
5. Press Up/Down button to select program (2/4).
6. Press Right button to delete a program.
Press Up/Down button to select DEL.
7.
8. Press Right button to delete program.
9. Press Left button to exit to main screen.
On/
IntelliChlor
Press Menu button > IntelliChlor 13/14 displays.
1.
Enable IntelliChlor: Press Right button.
2.
Press Up/Down button select YES.
3.
Sanitizer Output Level for Pool and Spa:
Displays the percentage of time chlorine is produced per hour of pump
run time. For example (60%) produces chlorine 60% of the hour; 36
minutes ON, 24 minutes OFF.
4. Press Right button to select POOL Sanitizer Output %.
5. Press Up/Down button adjust Sanitizer Output % for Pool
(0-100%).
6. Press Right button to select SPA Sanitizer Output %.
7. Press Up/Down button adjust Sanitizer Output % for Spa
(0-100%).
Super Chlorination:
Displays the percentage of time chlorine is produced per hour of
pump run time. For example (60%) produces chlorine 60% of the
hour; 36 minutes ON, 24 minutes OFF.
8. Press Right button, select SUPER CHLR.
9. Press Up/Down button, select YES.
10. Press Right button, select RUN HOURS.
11. Press Up/Down button, set hours to run (0-72).
View Super Chlorination Status:
12. Press Right button to view Salt status ppm.
13. Press Left button to exit to main screen.
CONTROL SYSTEM
®
QUICK REFERENCE GUIDE
Electronic Chlorine Generator
®
(13/14)