Table of Contents
Advertisement
LX-100EZ EASYTOUCH POOL/SPA CONTROL SYSTEM
INSTALLATION AND OWNERS MANUAL
Attention Installer.
This manual contains important information about the installation, operation and safe use of this
product. This information should be given to the owner/operator of this equipment.
Pentair Pool Products
1620 Hawkins Ave., Sanford, NC 27330 • (919) 774-4151
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400
Rev. F 3-26-04
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Important Notice
1
P/N 520050
Advertisement
Table of Contents
Related Manuals for Pentair EasyTouch Pool/Spa Control System LX-100EZ
Summary of Contents for Pentair EasyTouch Pool/Spa Control System LX-100EZ
-
Page 1: Important Safety Instructions
This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment. Pentair Pool Products 1620 Hawkins Ave., Sanford, NC 27330 • (919) 774-4151 10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400 Rev. -
Page 2: Table Of Contents
IMPORTANT SAFETY INSTRUCTIONS ... 5 SYSTEM INCLUDES ... 5 EQUIPMENT LOCATION ... 5 RECOMMENDED HYDRAULIC SCHEMATIC ... 6 PLUMBING REQUIREMENTS ... 7 LX-100 RF POWER/LOAD CENTER ... 8 HIGH VOLTAGE WIRING ... 8 GENERAL ... 8 SYSTEM POWER ... 8 EQUIPMENT POWER ... - Page 3 IMPORTANT SAFETY INSTRUCTIONS ... 21 INTRODUCTION ... 22 SAFETY FEATURES ... 22 HEATER PROTECTION ... 22 POOL CLEANER PROTECTION ... 22 HAND-HELD REMOTE ... 22 LX-100 RF POWER/LOAD CENTER ... 23 FILTER PUMP and POOL CLEANER Time Clocks ... 23 SPA Service Switch ...
- Page 4 This page is blank. P/N 520050 Rev. F 3-26-04...
-
Page 5: Important Safety Instructions
INSTALLATION MANUAL LX-100EZ EASYTOUCH POOL-SPA CONTROL SYSTEM IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS All wiring must be performed by a qualified electrician. Basic safety precautions and local codes should always be followed when installing and using this electrical equipment. To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. -
Page 6: Recommended Hydraulic Schematic
RECOMMENDED HYDRAULIC SCHEMATIC Refer for “PLUMBING REQUIREMENTS” on page 7. SENSOR WATER REMOTE SPA-SIDE P/N 520050 Rev. F 3-26-04... -
Page 7: Plumbing Requirements
Plumb system in accordance with “RECOMMENDED HYDRAULIC SCHEMATIC” on page 6, local codes and the following guidelines. Bring all lines back to the equipment pad. 1. Spa should be at or above the level of the pool. If spa is attached to pool, provide a dam between the two bodies of water to allow spa overflow into pool. -
Page 8: Lx-100 Rf Power/Load Center
LX-100 RF POWER/LOAD CENTER Select a convenient location to mount the LX-100 RF Power/Load Center. Ensure that the location is greater than 5 feet from the water’s edge and no further than 15 feet from any motorized valves (otherwise Valve Actuator cables will need to be extended). -
Page 9: Low Voltage Cables
Install cable between the low voltage compartment of the LX-100 RF Power/Load Center and the various pieces of equipment. Provide plastic or metallic conduit where cables run underground, through concrete, etc. Never install low voltage and high voltage wires in the same conduit. It is advisable to maintain a minimum distance of 12”... -
Page 10: Receiver Circuit Board
Mounted to the back of the LX-100 RF Power/Load Center is the Receiver Circuit Board. On the circuit board, you will discover the following: 1. A 4-position configuration switch (designated S2), which can be used to configure an automatic countdown cycle for the Spa and/or the Aux1 circuit. (Aux1 is designated as button “A” on Hand-held Remote). -
Page 11: Customizing The Communication Link
CUSTOMIZING THE COMMUNICATION LINK The communication link between the Receiver and Hand-held Remote can be customized to prevent interference to or from other RF systems. To accomplish this, there is a 10-position configuration switch located on the Receiver circuit board and inside the Hand-held Remote. Units are shipped from the factory with all switches in the “ON”... -
Page 12: Valve Actuators
Remove knob, handle and four screws from cap of valve(s) to be motorized, and use the four mounting screws provided to mount Valve Actuator(s) to valve(s). Run cables to low-voltage wiring compartment of LX-100 RF Power/Load Center, and plug into circuit board at the appropriate Valve Socket: Plug intake (suction) valve into INT VLV Socket. -
Page 13: Heater Connections
HEATER CONNECTIONS DUAL THERMOSTAT GAS HEATER/HEAT PUMP Inside the heater, connect three 18 AWG wires in parallel with the heater toggle switch or in accordance with the Heater Manufacturer’s instructions. Do not disconnect or bypass the flow, pressure or high limit switches. Place the heater toggle switch in the “OFF”... -
Page 14: System Options
SYSTEM OPTIONS AUTOMATIC COUNTDOWN CYCLE There is a 4-position configuration switch (designated S2) located on the Receiver circuit board. This switch can be used to set a countdown cycle (time-out feature) for the Spa and/or Aux1 circuit. Once this feature has been enabled, the equipment will automatically turn off after the countdown cycle irrespective of how the circuit was turned on (by Hand-held Remote or optional Indoor Remote, or Spa-side Remote). -
Page 15: Spa-Side Remote Control
SPA-SIDE REMOTE CONTROL The optional Spa-side Remote Control is a double-insulated device which is ETL-listed for installation within 5 feet of the water’s edge. It is typically installed at the tile-line of the spa wall (above water level), or in the deck within arm’s reach of the spa. -
Page 16: Pool Cleaner
POOL CLEANER For systems which incorporate a booster pump pool cleaner, it is possible to add a mechanical time clock for programming the daily cleaning cycles. Install 24-Hour Time Clock (model TMR-LX) into LX-100 RF Power/Load Center faceplate at the POOL CLEANER location, and plug into top of circuit board at CLNR TIMER socket, in accordance with instructions provided. -
Page 17: Water Temperature Sensor
WATER TEMPERATURE SENSOR For use with optional Indoor Control Panel only. Select a convenient location to mount the Temperature Sensor (model TS-5L) in the plumbing system between the filter pump and the heater. Drill a 5/16” diameter hole in the pipe, and insert the Sensor. Use a screwdriver to open the hose clamp (included). -
Page 18: Cp-100 Indoor Controller
CP-100 (OPTIONAL) INDOOR CONTROLLER 2 qty. separate 150 foot spools of 6-conductor 26 AWG communication cable are provided (one black and one silver) to connect to the CP-100 Controller. Cable lubricant must be used when pulling these cables through the conduit. Select a convenient location inside the house or other weather-protected area to mount the CP-100 Controller. -
Page 19: System Start-Up
SYSTEM START-UP Apply power to the system. At the LX-100 RF Power/Load Center, verify that the POWER "ON" status light is illuminated, and make sure that all of the Service Switches are in the “AUTO” position. If the status light is not on, check the 3 amp circuit breaker which is located above the faceplate. If the circuit breaker has tripped (indicated by a white tab), push to reset. - Page 20 CP-100 OPTIONAL INDOOR CONTROL PANEL If the system has an Indoor Controller, verify that there is a TEMPERATURE Display and check that the EQUIPMENT STATUS INDICATORS are functioning when the Push-buttons are activated. If there is no status display, check the connections at each end of the communication cables very carefully. If necessary, crimp new modular connectors to the cables.
-
Page 21: Important Safety Instructions
OWNER’S MANUAL LX-100EZ EASYTOUCH POOL-SPA CONTROL SYSTEM IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS. CAUTION When operating or servicing this electrical equipment, basic safety precautions should always be observed including the following: WARNING To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. CAUTION The Hand-held Remote is not waterproof. -
Page 22: Introduction
The LX-100EZ is an electronic control system which is designed to coordinate and operate all of the equipment associated with your swimming pool and spa. The system is comprised of three principle components: 1. Hand-held Remote. 2. Power Center. 3. Motorized Valves (2 qty). The Remote provides Push-button control of the equipment from the convenience of your fingertips;... -
Page 23: Lx-100 Rf Power/Load Center
LX-100 RF POWER/LOAD CENTER Located in close proximity to your pool equipment, the LX-100 RF Power/Load Center houses mechanical time clocks for your filter pump and pool cleaner (if applicable), and manual switches for your Pool Serviceperson. FILTER PUMP and POOL CLEANER Time Clocks Check with your Pool Builder or Service Company as to the amount of time required to provide efficient filtration and cleaning of your pool. -
Page 24: Spa Service Switch
SPA Service Switch For normal system operation, keep this Switch in the “AUTO” position. The “FILL” and “DRAIN” positions are used when cleaning the spa. FILTER Service Switch For normal system operation keep this Switch in the “AUTO” position. The “OFF” and “ON” positions allow your Pool Serviceperson to override the FILTER PUMP Time Clock without altering the program. -
Page 25: Motorized Valves
MOTORIZED VALVES Your control system is designed to activate two motorized valves, which automatically rotate between pool and spa circulation whenever Push-button #1 (SPA) is activated by the Hand-held Remote. These valves are also activated from the “FILL” and “DRAIN” positions of the SPA Service Switch at the LX-100 RF Power/Load Center. An additional motorized valve may have been installed for a custom hydraulic application, such as a fountain or waterfall, or (in lieu of a booster pump) to activate your pool cleaner. -
Page 26: System Options
SYSTEM OPTIONS SPA-SIDE REMOTE CONTROL A 4-button waterproof Remote Control may have been installed into the wall of your spa. This will enable you to control the equipment while sitting in your spa. Your Pool Builder should have custom-labeled each button for your specific application. The RED Button duplicates Push-button SPA by the Hand-held Remote (activates the spa circulation). -
Page 27: Indoor Controller
INDOOR CONTROLLER Installed in a convenient location inside your house, the Controller gives you fingertip control of all the equipment associated with your swimming pool and spa. Equipment PUSH-BUTTONS #S, #1, #2 and #3 Four Push-buttons are provided for activating the various pieces of equipment. Your Pool Builder has custom-labeled each Push-button for your specific application. -
Page 28: Maintenance
CLEANING THE SPA For cleaning or maintenance purposes, it is possible to use the Control System to automatically empty your spa and then to refill with clean water from the Pool. At the Power Center: 1. Set the SPA Service Switch to “DRAIN” position. 2. -
Page 29: Trouble-Shooting
Your Control System is designed to provide years of trouble-free pool and spa enjoyment. However, if at any time your System should behave erratically, consult the following Check List, which should help to alleviate any problems caused by operator error. If you are still unable to solve your particular symptom, refer the situation to a qualified Pool Service Company. -
Page 30: Rf Trouble-Shooting Table
Symptom POWER LED does not light. COM LINK LED does not light or blink. In normal operation LED will blink at least every 2 seconds. COMMAND LED does not light when Hand-held Remote button(s) is pressed - unit fails to operate. Unit functions, but some circuits do not work, or operate the incorrect circuit. -
Page 31: Warranty
For questions, repairs, replacement parts, or information on possible Authorized Service Centers within your vicinity call: Pentair Pool Products ~ 800-831-7133 Or visit us on the Internet at www.pentairpool.com Rev. F 3-26-04 P/N 520050... - Page 32 SAVE THESE INSTRUCTIONS. Pentair Pool Products 1620 Hawkins Ave., Sanford, NC 27330 • (919) 774-4151 10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400 P/N 520050 Rev. F 3-26-04...