Advertisement
Available languages
Available languages
the button on the buckle and move them to the sides
(diag. 1 4)
8. Make sure your child is seated comfortably on the
child car seat, adjust the harness straps around the
childs body without pulling them too tight, join the
two harness straps (diag. 15A) and click them into the
buckle (diag. 15B).
9. Use the adjuster knob A fitted at the top of the
backrest to adjust the height of the child car seat's
headrest, it must be fitted so as to allow the harness
straps to come out at the height of the child's shoul-
ders (diag. 16)
10. To tighten the restraint harnesses of the child car seat,
pull the adjustment strap I until it is correctly fitted to
the child's body.
11. Check that the child car seat is fitted correctly as seen
in the diagram (diag. 18).
To remove the child from the child car seat, press the
button on the buckle and release the restraint harness
(diag. 1 9)
FITTING THE CHILD CAR SEAT INTO THE CAR AND
SEATING A GR. 2 or 3 CHILD (15-36 KG)
To change the configuration of the child car seat from Gr. 1
to Gr. 2-3, it is necessary first of all to remove the restraint
harness following the instructions below:
1. Release the child car seat harnesses from the buckle
(diag. 14)
2. Rotate and release the two belt routing plates R
found under the seat (diag. 20A) sliding them out of
the two slots in the fabric cover (diag. 20B).
3. Remove the two harness straps from the locking pla-
te Q (diag. 21)
4. Rotate and release the two belt routing plates N from
the backrest (diag. 22)
5. From the front of the seat, slide out the two sections
of the harness through the two red diagonal belt rou-
ting slots C (diag. 23).
6. Store these two harness straps in a safe place for
future use.
7. Now slide the buckle and the fabric crotch strap
through the slot in the centre of the seat, so that it
all fits inside the housing on the child seat (diag. 24A,
24B and 24C).
The child car seat is now ready to be installed for Group
2 and 3 children.
8. Place the child car seat onto the chosen forward fa-
cing car seat (diag. 25)
9. Thread the diagonal car safety belt down behind the
headrest and through the relative red diagonal belt
routing slot C below the headrest. Place your child
carefully into the car seat, and check that the child
is sitting with his back correctly placed against the
backrest of the child car seat (diag. 26)
10. Click the car safety belt into the buckle so that both
the abdominal and the diagonal straps pass under the
armrest (diag. 27).
11. Check the height of the head rest and, if it is not
correct, adjust it accordingly: see paragraph "ADJU-
STING THE HEIGHT OF THE HEAD REST"
12. Pull the diagonal car safety belt strap towards the re-
tractor, to ensure the belt is tight and fitting properly
over the child's legs and chest (diag. 28).
13. Check that the child car seat is fitted correctly as seen
in the diagram (diag. 29).
WARNING!
• Always check that the seat belt is positioned correctly
and no parts are twisted.
• Check that the diagonal safety belt fits correctly
across the child's shoulder and does not press on he
childs neck; adjust the headrest accordingly.
• Check that the car safety belt retractor is behind the
backrest of the car seat (or at least aligned to it).
To remove a child from a Group 2 and 3 child car seat:
1. Release the car safety belt from its buckle.
2. Remove the car safety belt from the child's body.
3. Carefully remove the child from the car seat.
WARNING! If you do not intend to remove the child car
seat from the vehicle, slot the car safety belts back into
the buckle, so that the child car seat remains fastened sa-
fely inside the vehicle even when not used; this will avoid
danger during an accident or sudden braking of the car.
ADJUSTING THE HEIGHT OF THE HEAD REST
The height of the headrest can be adjusted to a range of
positions to adapt the child car seat to the height of the
child. When it is correctly adjusted, it ensures:
• That the child's head is always held in place and well
protected (Gr. 1-2-3).
• That the child car seat restraint harnesses are always
at the right height, that is the shoulder straps (Gr. 1).
• That the diagonal car safety belts are always at the
right height as the straps are slotted through the he-
adrest C (Gr. 2-3).
To adjust the height of the headrest, turn the knob A fit-
ted at the top of the backrest until you reach the required
height (diag. 16).
REFITTING THE HARNESS FOR SEATING A GR. 1
CHILD (9-18 KG)
To refit the restraint harness to the child car seat, proceed
as follows:
1. Join the two ends of the harness straps, insert them
and connect them to the buckle (diag. 30)
2. Insert the two locking plates R, sliding them out
through the slots in the fabric cover and pulling them
out from under the seat (diag. 31).
3. Insert the two shoulder strap and the belt sequence N
locking plates through the two red diagonal belt slots
C and then through the backrest (diag. 32).
4. Connect the two harness straps to the locking plate
Q (diag. 33).
CLEANING AND MAINTENANCE
HOW TO CLEAN THE FABRIC COVER
The child car seat's fabric cover can be removed and clea-
ned by hand or in a washing machine at 30°C. Please re-
9
Advertisement
