Page 4
Data Points Used in Default Data Graphs ......69 Data Points Available to Include in Custom Data Graphs ....72 CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
CenTraVac™ chiller models CVHE, CVHF, and CVHG. The purpose of this guide is to assist you in using the Tracer AdaptiView display. The guide describes how to access the screens and the types of information that appear on the screens.
Animated color graphics indicate the status of the chiller and its components. AC power The Tracer AdaptiView display receives AC power through its power cable, which is connected to the Tracer UC800 controller. The Tracer UC800 controller must be powered...
Introduction Screen Overview The touch-sensitive areas of the Tracer AdaptiView display screen are described in detail in this section. Figure 1, three areas are identified, which correspond to the following subsections: “Chiller Status Area, ” p. 8 “Main Display Area/Home Screen, ” p. 9 “Main Menu Area, ”...
Figure 1, p. 7) remains visible from every screen on the Tracer AdaptiView display. Basic information about chiller status and control appears on the face of the buttons and touch targets. When touched, the buttons and touch targets open other screens that provide more information and control access.
• Active chilled water setpoint (if chilled water control is available) • Evaporator water flow (animation in graphic indicates if evaporator is running) Touch anywhere within the white rectangular area to view the evaporator component screen. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Page 10
For more information, see “Viewing Unit Information (About This Chiller),” p. Log Sheet Touch the Log Sheet button to view the Log Sheet. Note: For more information, see “Viewing the Log Sheet,” p. Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 11
The screen saver also appears if you touch the animated graphic on the home screen. Alternately, if you touch the screen saver, the home screen appears. Figure 2. Screen saver Better graphic to come CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
(See, for example, the buttons on the evaporator component screen in Figure 3, which show the Active Chilled Water Setpoint and the Evaporator Water Pump Override). Note: For more information about changing settings, see “Equipment Settings, ” p. Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Touch the Settings button to view the Settings screen, which is separated into the following three categories: • “Equipment Settings,” p. 34 • “Display Settings,” p. 47 • “Security Settings,” p. 54 Note: Refer to the page numbers for detailed information about each category. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
To stop the chiller in either of these ways: 1. Touch the Stop button to initiate the chiller shutdown process. A confirmation screen appears (Figure Figure 4. Stop the Chiller confirmation screen Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Touch the Auto button to initiate the chiller restart process. You can observe the mode change to Auto. The chiller will wait until cooling is needed before starting the compressor. When the chiller is running normally, it automatically starts and stops as needed to reach its setpoints. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Alarms You can use the Tracer AdaptiView display to view alarms and to reset them. Alarms are communicated to the display immediately upon detection. Viewing the Alarms Screen Touch the Alarms button in the main menu area (Figure 1, p.
Description: Alarms are sorted alphanumerically by name, followed by the most recent. • Status: Alarms are sorted according to active/historic status (if you are viewing both active and historic alarms), followed by the most recent. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
If an active alarm is present, the alarm indicator button (Table 1, p. 8) appears in the upper left of the screen, as in Figure 6, p. 16. The icon on this button indicates the level of the most severe active alarm. Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Reports You can use the Tracer AdaptiView display to view a variety of reports and to create and edit a custom report. All reports contain live data that refreshes every 2–5 seconds. Viewing the Reports Screen Touch the Reports button in the main menu area (Figure 1, p.
“Appendix B: Reports, ” p. 62. The items included in the Log Sheet are those recommended by Trane. See current Trane service literature for more information. Notes: You can also access the Log Sheet by touching the Log Sheet button at the bottom of the home screen.
Page 21
Note: A page number appears in the lower right corner of the screen. If a screen contains more than one page, up/down arrows also appear for viewing the other pages, as in Figure Figure 9. Custom Report screen CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
• Display Software Build • Unit Sales Order Number • Application Part Number • Display Boot Code • Unit Serial Number • Boot Part Number • Hardware Serial Number • Build Part Number Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Note: You can also access the Chiller Operating Modes screen from the button in the upper left of the screen. In Figure 10, this button indicates that the chiller is running. Figure 10. Chiller Operating Mode screen CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
If less than 6 submodes are active, the submode rows that do not apply are blank. For detailed information about purge operating modes and submodes, see the EarthWise™ Purge System with Tracer AdaptiView™ Control Operation and Maintenance Guide (PRGD-SVX01A-EN). Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Data Graphs You can use the Tracer AdaptiView display to view a variety of default data graphs and to create up to six custom data graphs. The data sample rate is 30 seconds, and the data storage duration is 48 hours. These rates cannot be adjusted.
12-minute graph with 3 minutes between time labels • 40-minute graph with 10 minutes between time labels • 60-minute graph with 15 minutes between time labels • 4-hour graph with 1 hour between time labels Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 29
Figure 13. Set Axis Range screen 2. Touch the Manually set values button under either the Left Y-Axis or Right Y-Axis heading. Enter number buttons appear to the right of the minimum and maximum values. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
1. Touch the Create Custom button at the top left of any default data graph screen (see Figure 12, p. 28, for example). The Data Graph Points screen appears (Figure 14). Figure 14. Data Graph Points screen Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 31
Touch Remove to move the selected item to the left box. • To remove all of the items in the right box to the left box, touch Remove All. A confirmation screen appears, asking you to verify your request. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
27). The Add/Remove screen appears (see Figure 15, p. 31), but with no data on the screen. 2. Continue by following steps 3 through 5 of “Creating a custom data graph from a default data graph, ” p. Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
3. Touch Save. The screen you were previously viewing appears with your changes reflected in the table. Figure 17. Edit Data Point screen Deleting a Custom Data Graph Touch the Delete button at the top of a custom graph screen to delete the custom graph. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Equipment Settings You can use the Tracer AdaptiView display to monitor and change a variety of equipment settings. Viewing the Settings Screen Touch the Settings button in the main menu area (see “Main Menu Area, ” p. 13) to view the Settings screen.
Note: A page number appears in the lower right corner of the screen. If a screen contains more than one page, up/down arrows also appear for viewing the other pages, as Figure Figure 19. Example equipment settings screen (Chiller Settings shown) CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Page 36
20), touch the button that represents the setting you want. The button becomes shaded, and a Save button appears at the bottom of the screen. Figure 20. Example equipment settings screen with buttons for changing setting Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 37
“Manual Control Settings, ” p. 44. Touching Apply is the same as touching Save, except that you remain at the current screen after the change is communicated to the Tracer UC800 controller (Figure 24, p. 45). CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Valid numerical range appears on screen. Current Limit Control Softload Time Valid numerical range appears on screen. Current Limit Control Softload Start Point Valid numerical range appears on screen. Local Atmospheric Pressure Valid numerical range appears on screen. Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
• Set at the front panel (FP)—Refers to inputs that are entered by an operator using the Tracer AdaptiView display or by a technician using the Tracer TU service tool. Setpoint Source Arbitration The Tracer UC800 uses a process referred to as setpoint source arbitration to prioritize the selection of the setpoint source.
1. Touch the Settings button in the main menu area (Figure 1, p. 7). The Settings screen appears. 2. From the Settings screen, touch the Chiller Settings button. The Chiller Settings screen appears. Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 41
5. Touch the button the appropriate source button on the Setpoint Source screen. 6. Touch Save to complete the change. Note: The change applies to all arbitrated setpoints. Figure 23. Changing the setpoint source from an arbitrated setpoint screen CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Valid numerical range appears on screen. Outdoor Reset Ratio Valid numerical range appears on screen. Outdoor Start Reset Valid numerical range appears on screen. Outdoor Maximum Reset Valid numerical range appears on screen. Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Clear Restart Inhibit Timer XX:XX min:sec Clear Purge Exhaust Circuit Test Off/On • Auto Purge Rfgt Cprsr Suction Temp • On Purge Liquid Temp Purge Regen Cycle Off/On • Auto Carbon Tank Temp • On Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 45
Also, a Manual Override button appears in the upper left corner of the screen (see Figure 25, p. 46). • Touch Save. The change is communicated to the Tracer UC800 controller. The screen you were previously viewing appears. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Display Settings You can use the Tracer AdaptiView display to change the format of the information that appears on the display, and to clean the touch screen. Viewing the Settings Screen Touch the Settings button in the main menu area (see “Main Menu Area, ”...
(current value). Touch any of these buttons to view a screen where you can change the format (see Figure 28, p. 49 for an example). The button representing the format currently used is shaded (see the “MMDDYYYY” button in Figure 28). Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 49
2. Touch Save to confirm your selection and to return to the Display Preferences screen. Date Format You can use the Date Format screen to choose from the following date formats: • MMDDYYYY • YYYYMMDD • DDMMYYYY CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Figure 29, p. 51): • Arabic (Gulf Regions) • Chinese—China • Chinese—Taiwan • Czech • Dutch • English • French • German • Greek • Hebrew • Hungarian • Italian • Japanese • Korean Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 51
Figure 29 as an example). To change the language: 1. Touch the button that shows that language you prefer. 2. Touch Save to confirm your selection and to return to the Settings screen. CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Above the center line, the following date and time attributes appear: • Month • • Year • Hour • Minute • AM/PM To change the date or time: 1. Touch the square presenting the attribute you want to change. The square becomes highlighted. Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
3. Touch Save to confirm your selection and return to the Settings screen. Cleaning the Display On the Settings screen, touch Clean Display to disable the Tracer AdaptiView display screen for 15 seconds so that you can clean the screen without it responding to touch.
Security Settings If security if enabled, the Tracer AdaptiView display requires that you log in with a four- digit security PIN to make certain setting changes. This prevents unauthorized personnel from doing so. Note: The default security PIN is 7123. A technician must use the Tracer TU service tool to define a different PIN, or to recall it if forgotten.
Security Settings Disabling/Enabling Security The Tracer AdaptiView display gives you the ability to disable or enable the security feature that allows a user to log in and log out. To disable security, you must be logged in: 1. From the Settings screen, touch the Security button. The Security screen appears (Figure 33).
If the Log in screen appeared when you tried to change a setting, you return to that setting screen. Note: The PIN is valid until 30 minutes of inactivity pass, or until you log out. Figure 34. Log In Screen Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
1. Touch the Log out button. A confirmation screen appears (Figure 35). 2. Touch Yes to confirm that you want to log out. The Settings screen appears with a Log in button on it. Figure 35. Log out confirmation screen CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Troubleshooting Table 13 contains information to help troubleshoot the Tracer AdaptiView displays. Table 13. Tracer AdaptiView display troubleshooting guide Issue Possible causes/Solutions The screen only partially displays; the Auto and The UC800 configuration is invalid. Stop buttons appear, but there is no text.
Appendix A: Component Screen Data The following list contains all of the settings and status points that are available for viewing on the Tracer AdaptiView display. Chiller configuration determines which ones appear on the display. Component Settings and status points...
Page 60
Starter Current L1 (A) Starter Current L2 (A) Starter Current L3 (A) Starter Voltage AB Starter Voltage BC Starter Voltage CA Motor Winding Temp #1 Motor Winding Temp #2 Motor Winding Temp #3 Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 61
Chiller On—7 Days Pumpout Chiller On—7 days Pumpout Chiller On—7 days Pumpout Chiller Off—7 days Time Until Next Purge Run Purge Rfgt Cprsr Suction Temp Purge Liquid Temp Pumpout—Life Purge Regen Cycle Carbon Tank Temp CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Page 65
XXX.X °F/C° Cond Water Flow Status: Flow/No Flow Cond Differential Wtr Press XXX.X PSID/kPaD Approx Cond Water Flow XXXX gpm/lpm Second Condenser Ent Wtr Temp XXX.X °F/C° Second Condenser Lvg Wtr Temp XXX.X °F/C° CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Page 66
Outboard Bearing Temperature Condenser Condenser Approach Temperature Condenser Entering Water Temperature Condenser Leaving Water Temperature Condenser Refrigerant Pressure Condenser Saturated Refrigerant Temperature Condenser Water Flow Switch Status Condenser Pump Override Time Remaining Condenser Pump Override Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 67
Starter Current L2 Starter Current L3 Starter Current L3 Starter Energy Consumption—Not Resettable Starter Energy Consumption—Resettable Time of Last Reset Starter Load Power Factor Starter Power Consumption Starter Power Demand Starter Voltage Phase AB CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Page 68
Pumpout Chiller Off—7 Days Pumpout Chiller On—7 Days Pumpout—Life Purge Carbon Tank Temp Purge Liquid Temperature Purge Refrigerant Compressor Suction Temp Time at Last Regeneration Time Until Next Purge Run MM:SS Purge Top Level Operating Mode Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Approach Temperature Graph data point Axis Evaporator Approach Temperature Left Y-axis Condenser Approach Temperature Left Y-axis Approximate Evaporator Water Flow Right Y-axis Approximate Condenser Water Flow Right Y-axis Average Line Current Right Y-axis CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Page 70
Graph data point Axis Active Hot Water Setpoint Left Y-axis Condenser Leaving Water Temperature Left Y-axis Condenser Entering Water Temperature Left Y-axis Condenser Saturated Refrigerant Temperature Left Y-axis Approximate Condenser Water Flow Right Y-axis Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 71
Left Y-axis Pumpout Chiller On—7 Days Left Y-axis Pumpout Chiller Off—7 Days Left Y-axis Purge Average Daily Pumpout—7 Days Right Y-axis Purge Refrigerant Compressor Suction Temperature Right Y-axis Purge Liquid Temperature Right Y-axis CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Outdoor Air Temperature Condenser Refrigerant Pressure Condenser Approach Temperature Approximate Condenser Water Flow Second Condenser Leaving Water Temperature Second Condenser Entering Water Temperature Compressor Chiller Control Signal Oil Tank Pressure Oil Pump Discharge Pressure Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 73
Average Phase Voltage Purge Generator Frequency Command Daily Pumpout—24 Hours Pumpout Chiller On—7 Days Pumpout Chiller Off—7 Days Purge Average Daily Pumpout—7 Days Purge Refrigerant Compressor Suction Temperature Purge Liquid Temperature Purge Carbon Tank Temperature CTV-SVU01B-EN • Tracer AdaptiView Display Operations Guide...
Page 74
Appendix C: Data Graph Data Points Tracer AdaptiView Display Operations Guide • CTV-SVU01B-EN...
Page 76
Supersedes CTV-SVU01A-EN January 2008 www.trane.com For more information, contact your local Trane Trane has a policy of continuous product and product data improvement and reserves the right to office or e-mail us at comfort@trane.com change design and specifications without notice.