Sony XAV-701BT Service Manual page 9

(Sauth African model)
* For details on installing the microphone, see "Installing the microphone (
1
reverse side.
*
2 If your car antenna (aerial) is an ISO (International Organization for Standardization)
type, use the supplied adaptor to connect it. First connect the car antenna (aerial) to
the supplied adaptor, then connect the adaptor to the antenna (aerial) jack of the
unit.
*
3 Whether in use or not, route the microphone input cord such that it does not interfere
with driving. Secure the cord with a clamp, etc., if it is installed around your feet.
* 4
RCA pin cord (not supplied)
* 5
For details on connecting to the parking brake switch cord, see "Connecting the parking
brake lead ( )" on the reverse side.
* 6
Speaker impedance: 4 – 8 ohms × 4
* 7
The sound is output from this terminal only when ZONE x ZONE is activated. This terminal
outputs a fixed level regardless of the volume control of the unit.
* 8
A separate adaptor may be required.
* 9
Not supplied
* 10
USB connection cable RC-202IPV (not supplied). To connect an iPod via RC-202IPV, make
sure to connect the video output plug to AUX1 IN.
Max. supply current: 0.3 A AMP REM
PARKING BRAKE
* 5
* 4
EXT
* 2
From car antenna (aerial)
REMOTE IN*
MIC IN*
* 1
* 4
Equipment used in illustrations (not supplied)
Front speaker Rear speaker
Subwoofer iPod
Monitor Smartphone
A
FRONT AUDIO
OUT
REAR OUT
Z×Z L / R
SUB OUT REAR AUDIO
OUT
B
AUX AUDIO
IN
AUX IN
( VIDEO )
CAMERA
* not supplied
)" on the
Blue/white striped
Light green
AUX2 AUDIO
AUX2 IN
IN
AUX1 IN
CAMERA
8
Fuse (10 A)
3
REAR OUT
7
Z×Z L / R*
* 4
REVERSE IN
FRONT
AUDIO OUT
AUX1 AUDIO
IN
* 4
REAR SUB OUT
AUDIO OUT
Cautions
Run all ground (earth) leads to a common ground
(earth) point.
Power amplifier
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
Rear view camera
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the power supply connection cable to the
unit and speakers before connecting it to the auxiliary
power connector.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Install the unit with the monitor facing straight forward;
do not install it at a slanted angle.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
If no car circuits are rated high enough, connect the unit
directly to the battery.
Connection example
Notes ( -A)
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
Note ( -B)
You cannot use multiple auxiliary devices simultaneously, even if they are
connected to different terminals.
Video camera*
For details, see "Power connection diagram" on the reverse side.
From the car's power connector
* 6
From the car's speaker connector
* 9
* 10
* 10
* 4
* 4
Connection diagram
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
To the parking brake switch cord
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
Tip
You can use an RCA pin cord (not supplied) to connect auxiliary
devices.
To the +12 V power terminal of the car's rear lamp
lead (only when connecting the rear view
camera)
Warning
If you have a power antenna (aerial) without a relay box,
connecting this unit with the supplied power supply
connection cable may damage the antenna (aerial).
Notes on the control and power supply leads
The power antenna (aerial) control lead (blue) supplies +12 V DC when
you turn on the tuner, or when you activate the AF (Alternative
Frequency) or TA (Traffic Announcement) function.
If your car has a built-in FM/MW/LW antenna (aerial) in the rear/side
glass, connect the power antenna (aerial) control lead (blue) or the
accessory power supply lead (red) to the power terminal of the antenna
(aerial) booster. For details, consult your car dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit's speaker leads to each other.
Notes on connection
If "Output connection failure. " appears in the display, make sure the
speaker and amplifier are connected correctly.
To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
XAV-701BT/741
4 Yellow Continuous power supply
5 Blue Power antenna (aerial) control
6 Orange/white Switched illumination power supply
7 Red Switched power supply
8 Black Ground (earth)
Positions 1, 2, and 3 do not have pins.
1 + Speaker, rear, right
Purple
2 – Speaker, rear, right
3 + Speaker, front, right
Gray
4 – Speaker, front, right
5 + Speaker, front, left
White
6 – Speaker, front, left
7 + Speaker, rear, left
Green
8 – Speaker, rear, left
Negative polarity positions 2, 4, 6, and 8 have striped leads.
9