Sony XAV-701BT Service Manual page 8

XAV-701BT/741
(E (PAL) model)
Equipment used in illustrations (not supplied)
Front speaker Rear speaker Power amplifier
Subwoofer iPod Rear view camera
Monitor Smartphone
A
FRONT AUDIO
OUT
REAR OUT
Z×Z L / R
SUB OUT REAR AUDIO
OUT
B
AUX AUDIO
IN
Video camera*
AUX IN
( VIDEO )
CAMERA
* not supplied
Cautions Connection diagram
Run all ground (earth) leads to a common ground
To a common ground (earth) point
(earth) point.
First connect the black ground (earth) lead, then connect the yellow
This unit is designed for negative ground (earth) 12 V and red power supply leads.
DC operation only. To the power antenna (aerial) control lead or the
Do not disassemble or modify the unit. power supply lead of the antenna (aerial) booster
Do not install in locations which interfere with airbag Notes
operation. It is not necessary to connect this lead if there is no power antenna
(aerial) or antenna (aerial) booster, or with a manually-operated
Do not get the leads under a screw, or caught in moving
telescopic antenna (aerial).
parts (e.g. seat railing).
If your car has a built-in FM/AM antenna (aerial) in the rear/side
Before making connections, turn the car ignition off to glass, see "Notes on the control and power supply leads."
avoid short circuits. To AMP REMOTE IN of an optional power
Connect the yellow and red power supply leads only amplifier
after all other leads have been connected. This connection is only for amplifiers. Connecting any other system
Be sure to insulate any loose unconnected leads with may damage the unit.
electrical tape for safety. To a car's illumination signal
Do not press on the LCD when installing the unit. Be sure to first connect the black ground (earth) lead to a common
Install the unit with the monitor facing straight forward; ground (earth) point.
do not install it at a slanted angle. To the +12 V power terminal which is energized
when the ignition switch is set to the accessory
Notes on the power supply lead (yellow)
position
When connecting this unit in combination with other
Notes
stereo components, the amperage rating of the car If there is no accessory position, connect to the +12 V power
circuit to which the unit is connected must be higher (battery) terminal which is energized at all times.
than the sum of each component's fuse amperage rating. Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
If no car circuits are rated high enough, connect the unit
If your car has a built-in FM/AM antenna (aerial) in the rear/side
directly to the battery.
glass, see "Notes on the control and power supply leads."
To the +12 V power terminal which is energized
at all times
Connection example
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
To the parking brake switch cord
Notes ( -A)
To an auxiliary device such as a portable media
Be sure to connect the ground (earth) lead before connecting the
amplifier. player, game console, etc. (not supplied)
The alarm will only sound if the built-in amplifier is used.
Tip
You can use an RCA pin cord (not supplied) to connect auxiliary
Note ( -B)
You cannot use multiple auxiliary devices simultaneously, even if they are devices.
connected to different terminals. To the +12 V power terminal of the car's rear lamp
lead (only when connecting the rear view
camera)
Notes on the control and power supply leads
REM OUT lead (blue/white striped) supplies +12 V DC when you turn on
the unit.
If your car has built-in FM/AM antenna (aerial) in the rear/side glass,
connect REM OUT lead (blue/white striped) or the accessory power
supply lead (red) to the power terminal of the existing antenna (aerial)
booster. For details, consult your dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit's speaker leads to each other.
Notes on connection
If "Output connection failure. " appears in the display, make sure the
speaker and amplifier are connected correctly.
To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
XAV-701BT/741
Black Orange/white striped
REM OUT
Blue/white striped Red
Max. supply current: 0.4 A
Yellow
Light green
White
White/black striped
Gray
Gray/black striped
Green
* 4
Green/black striped
Purple
Purple/black striped
AUX2 AUDIO
IN
AUX2 IN
AUX1 IN
XAV-701BT
* 9
EXT
CAMERA
From car antenna (aerial) * 4
REMOTE IN* 8
Fuse (10 A)
XAV-701BT only
3
MIC IN*
REAR OUT
7
Z×Z L / R*
* 2
* 4
REVERSE IN
FRONT
AUDIO OUT
AUX1 AUDIO
IN
* 4
* 4
REAR SUB OUT
AUDIO OUT
* 1 Speaker impedance: 4 – 8 ohms × 4
* 2 The microphone is supplied with
XAV-701BT only. For details on installing
the microphone, see "Installing the
microphone (XAV-701BT only) (
the reverse side.
*
3 The microphone input cord is available
on XAV-701BT only. Whether in use or
not, route the microphone input cord
such that it does not interfere with
driving. Secure the cord with a clamp,
etc., if it is installed around your feet.
* 4 RCA pin cord (not supplied)
ILLUMINATION
Foot brake type
Parking brake switch cord
* 5
PARKING BRAKE
XAV-701BT only
A 1 2
Left
a
b
Right
* 1
Clips (not supplied)
Left
Face the hook inwards.
Right
* 6
* 9
4
*
* 5 For details on connecting to the parking
brake switch cord, see "Connecting the
parking brake lead ( )" on the reverse
A
side.
1
)" on * 6 not supplied
* 7 The sound is output from this terminal
only when ZONE x ZONE is activated.
This terminal outputs a fixed level
regardless of the volume control of the
unit.
*
8 A separate adaptor may be required.
* 9
USB connection cable RC-202IPV (not
supplied). To connect an iPod via
RC-202IPV, make sure to connect the
video output plug to AUX1 IN.
Larger than 182 mm (7 / in)
1 4
Larger than 111 mm (4
B
Size:
5 × max. 8 mm
7 ( / 32 × max. 5 / 16 in)
8 8
Hand brake type
Parking brake switch cord
B 1 2
c a b
a b
a
b
Clip (not supplied)
2 3
Dashboard
3 / 8 in)
Claws
To the dashboard/center console
Bracket
Parts supplied with your car
Size:
5 × max. 8 mm
( 7 / × max. 5 / in)
32 16
Bracket
Precautions Mounting the unit
Choose the installation location carefully so that the unit
will not interfere with normal driving operations.
-A Mounting the unit with the supplied
Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperature, such as in bracket
direct sunlight or near heater ducts.
1
Position the supplied bracket inside the
Use only the supplied mounting hardware for a safe and
dashboard.
secure installation.
2 Bend the claws outward for a tight fit.
To open/close the front panel smoothly, insert/eject a
disc easily, and especially to drive safely, a certain 3
Mount the unit onto the supplied bracket .
distance between the front panel and the shift lever is
necessary. The necessary distance differs, depending on
-B Mounting the unit in a Japanese car
the shift lever position of your car. Before installing the
unit, choose the installation location carefully so that
You may be able to install this unit in some makes of
you can drive safely.
Japanese cars without the supplied bracket. If you cannot,
consult your Sony dealer.
87 mm (3 1 / in)
2
Shift lever When mounting this unit to the preinstalled brackets of
your car, use the supplied screws in the appropriate
screw holes, based on your car: T for TOYOTA, M for
MITSUBISHI and N for NISSAN.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connecting the parking brake
Notes
lead
To avoid a malfunction, install only with the supplied screws .
Do not apply excessive force to the buttons of the unit.
Do not press on the LCD.
Be sure to connect the parking brake lead (light green) of
Before mounting, make sure there is nothing on the top of the unit.
the power supply connection cable to the parking brake
switch cord. The mounting position of the parking brake
switch cord depends on your car. Consult your car dealer
Warning if your car's ignition
or your nearest Sony dealer for further details.
has no ACC position
Installing the microphone
Be sure to set the Auto Off function. For details, refer to
the supplied "Operating Instructions. "
(XAV-701BT only)
The unit will shut off completely and automatically in the
set time when no source is selected, which prevents
To capture your voice during handsfree calling, you need battery drainage.
to install the microphone . If you do not set the Auto Off function, press and hold
until the display disappears each time
Cautions
you turn the ignition off.
Keep the microphone away from extremely high
temperatures and humidity.
It is extremely dangerous if the cord becomes wound
Reset button
around the steering column or gearstick. Be sure to keep
it and other parts from obstructing your driving.
If airbags or any other shock-absorbing equipment is in When the installation and connections are completed, be
your car, contact the store where you purchased this sure to press the reset button with a ballpoint pen, etc.
unit, or the car dealer, before installation.
-A Installing on the sun visor
1
Install the microphone a on the clip b .
2 Install the clip b on the sun visor.
3
Install clips (not supplied) and adjust the length
and position of the cord so that it does not
obstruct your driving.
-B Installing on the dashboard
1 Install the microphone a on the clip b , then
place the cord along the groove of the clip b .
2
Attach the clip b to the dashboard with the
double-sided tape c .
3
Install a clip (not supplied) and adjust the length
and position of the cord so that it does not
obstruct your driving.
Notes
Before attaching the double-sided tape c , clean the surface of the
dashboard with a dry cloth.
Adjust the microphone angle to the proper position.
The microphone a can be installed without using the clip .
b
In this case, directly attach the microphone to the dashboard with the
double-sided tape c . Keep the unused clip b for future use.
Removing the bracket
Before installing the unit, remove the bracket
from the unit.
1
Insert both release keys together between the
unit and the bracket until they click.
2 Pull down the bracket , then pull up the unit to
separate them.
Adjusting the frames
You can adjust the projecting part of the unit when the
unit is mounted.
Projecting part
Shift lever
1 Remove the screws from both sides of the unit.
2
Choose a screw hole from , or on each
frame .
If you secure the frames with the screw holes (default position),
it will maximize the projecting part of the unit. On the other hand,
screw holes will minimize the projecting part.
3 Reattach the frames with the selected screw
holes with the removed screws .
Notes
Choose the same screw hole position on both frames.
If you intend to secure the frames with screw holes or , make sure
that there is enough space in the dashboard of your car for the unit.