Blocking Channels; Unlocking Programs Temporarily; Locking Video Inputs - Toshiba 32HLX95 Owner's Manual

Blocking channels

With the Channels Block feature, you can block specific
channels. You will not be able to tune blocked channels unless
you clear the setting first.
To block channels:
1. Press MENU and highlight the Locks menu icon.
To exit the Locks menu,
press MENU.
2. Press z to display the
PIN code entering
screen.
3. Enter your four-digit PIN
code and press ENTER
(see page 80 for details).
4. Press z to highlight Channels Block and then press ENTER.
5. Using the yzx • buttons, select the input for which you
want to change the rating limits (ANT1, ANT2, or Cable
Box, if connected) and press ENTER.
A list of the channels available for that input will be displayed
along with the call letters for each channel, if available.
6. Press yz to highlight the
channel you want to
block, then press ENTER,
which puts an "X" in the
box next to that channel.
7. Repeat step 6 for other
channels you want to
block.
8. Highlight Done and
press ENTER.
To unblock individual channels:
In step 6 above, press yz to highlight the channel you want to
unblock, and then press ENTER to remove the "X" from the
box, and highlight Done, and then press ENTER.
To block all channels at once:
Highlight Block All in step 6 above, and then highlight Done,
and press ENTER.
To unblock all locked channels at once:
Highlight Allow All in step 6 above, and then highlight Done,
and press ENTER.
Channels Block
1
2
3
4
5
6
7
8
9
10
Note: Channel blocking may not take effect if you have a cable
box connected and use the cable box controls to change channels.
82
Chapter 9: Using the Locks menu
Locks
Enable Rating Blocking Off
Edit Rating Limits
Channels Block
Input Lock Off
Front Panel Lock Off
Game Timer Off
New PIN Code
Navigate Select CH RTN Back EXIT Exit
Channels Block
1 ANT 1
2 ANT 2
3
Cable Box
4
5
6
7
Allow All
8 Block All
9
Cancel
10 Done
ANT 1
ANT 1
ANT 2
Cable Box
Allow All
Block All
Cancel
Done
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.

Unlocking programs temporarily

If you try to watch a TV program that exceeds the rating limits
you set, the TV enters program lock mode. You can either
unlock the program temporarily or select a non-locked program
to watch.
To temporarily unlock the program:
1. Press MUTE.
2. Enter your four-digit PIN code and press ENTER. If the
correct code is entered,
the program lock mode
is released and the
normal picture appears.
All locking is disabled
until the TV is turned
off, and will be enabled
when the TV is turned on again.

Locking video inputs

ANT 1
You can use the Input Lock feature to lock the video input
sources (VIDEO 1, VIDEO 2, ColorStream HD 1,
ColorStream HD 2, HDMI, PC) and channels 3 and 4. You
will not be able to view the input sources or channels until you
turn off the input lock.
To lock the video inputs:
1. Press MENU and highlight the Locks menu icon.
2. Press z to display the PIN code entering screen.
3. Enter your four-digit PIN code and press ENTER.
4. Press z to highlight Input Lock and press ENTER.
5. Press yz to select the level of video input locking you
prefer, as described below:
Video: Locks, Built-in
DVD, VIDEO 1,
VIDEO 2, ColorStream
HD 1, ColorStream HD
2, HDMI, and PC.
Video +: Locks, Built-in
DVD, VIDEO 1,
VIDEO 2, ColorStream
HD 1, ColorStream HD
2, HDMI, PC and channels 3 and 4. Select Video + if you
use the antenna terminal to play a video tape.
Off: Unlocks all video input sources.
6. Press ENTER.
Note: When a CableCARD™ is inserted, Video + will behave the same
as Video lock.
Locks Active
Enter PIN code to temporaily un-
block.
* * * *
Cancel Done
Locks
Enable Rating Blocking Off
Off
Edit Rating Limits
Video
Channels Block Video +
Input Lock Off
Front Panel Lock Off
Game Timer Off
New PIN Code
Navigate Select CH RTN Back EXIT Exit