Connecting An Hdmi ™ Or Dvi Device To The Hdmi; Input - Toshiba Regza 42XV545U Owner's Manual

52XV545U_EN.book Page 16 Monday, August 4, 2008 10:54 AM
Connecting an HDMI
to the HDMI input
The HDMI input on your TV receives digital audio and
uncompressed digital video from an HDMI source
device, or uncompressed digital video from a DVI
(Digital Visual Interface) source device.
This input is designed to accept HDCP (High-
Bandwidth Digital-Content Protection) program
material in digital form from EIA/CEA-861-D–
[1]
compliant consumer electronic devices (such as a set-
top box or DVD player with HDMI or DVI output).
The HDMI input can accept and display VGA, SVGA,
XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p
(60Hz), 1080i (60Hz), and 1080p (24Hz/60Hz) signal
formats. For detailed signal specifications, see page 73.
Supported Audio format: Linear PCM, sampling rate
32/44.1/48 kHz
Note:
• To connect a PC to the HDMI input, see page 19.
• Some legacy HDMI sources may not work properly with your
HDMI TV, due to the adoption of new standards. Please try
setting the following three options (Lip-Sync Latency, Deep
Color, x.v.Color) to Off. Your legacy HDMI source should
operate properly with your TV. See page 73.
To connect an HDMI device, you will need:
one HDMI cable (type A connector) per HDMI device
•
– For proper operation, it is recommended that you use an
HDMI cable with the HDMI Logo (
– To display an 1080p/60Hz signal format, you will need a
High Speed HDMI cable. Conventional HDMI/DVI cable
may not work properly.
– HDMI cable transfers both video and audio. Separate
analog audio cables are not required (see illustration).
– See "Setting the HDMI ™
TV upper back panel
HDMI device
VIDEO AUDIO
L R
IN IN
OUT
L R
To view the HDMI device video:
Select the HDMI 1, HDMI 2, HDMI 3, or HDMI 4 video
input source on the TV.*
* To select the video input source, press INPUT on the remote control
(- page 42). To program the TV remote control to operate other
devices, see Chapter 3.
16
Chapter 2: Connecting your TV
™ or DVI device
).
audio mode" (- page 39).
TV right side panel
HDMI OUT
To connect a DVI device, you will need:
one HDMI-to-DVI adapter cable (HDMI type A
•
connector)
– For proper operation, the length of an HDMI-to-DVI
adapter cable should not exceed 9.8 ft (3m). The
recommended length is 6.6 ft (2m).
one 3.5mm Stereo to RCA Y-Cable
•
– An HDMI-to-DVI adapter cable transfers video only.
Separate analog audio cables are required (see
illustration).
™
– See "Setting the HDMI audio mode" (- page 39).
TV upper back panel
DVI device
VIDEO AUDIO
L R
IN IN
OUT
L R
Note: To ensure that the HDMI or DVI device is reset properly,
it is recommended that you follow these procedures:
• When turning on your electronic components, turn on the
TV first and then the HDMI or DVI device.
• When turning off your electronic components, turn off the
HDMI or DVI device first and then the TV.
[1]EIA/CEA-861-D compliance covers the transmission of
uncompressed digital video with high-bandwidth digital content
protection, which is being standardized for reception of high-
definition video signals. Because this is an evolving technology, it
is possible that some devices may not operate properly with the TV.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
DVI/HDCP
OUT
XV545U (E/F) Web 177.8:228.6