1. Manuals
  2. Brands
  3. ZyXEL Communications Manuals
  4. Gateway
  5. Network Device P-2302
  6. User manual

ZyXEL Communications Network Device P-2302 User Manual

802.11g wireless voip station gateway with built-in dect base station
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
P-2302HWUDL-P1 Series
802.11g Wireless VoIP Station Gateway
with Built-in DECT Base Station
User's Guide
Version 3.60
10/2006
Edition 1
www.zyxel.com

Advertisement

Table of Contents
loading

Related Manuals for ZyXEL Communications Network Device P-2302

Summary of Contents for ZyXEL Communications Network Device P-2302

  • Page 1 P-2302HWUDL-P1 Series 802.11g Wireless VoIP Station Gateway with Built-in DECT Base Station User’s Guide Version 3.60 10/2006 Edition 1 www.zyxel.com...

  • Page 3: About This User's Guide

    Help us help you. Send all User Guide-related comments, questions or suggestions for improvement to the following address, or use e-mail instead. Thank you! The Technical Writing Team, ZyXEL Communications Corp., 6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 300, Taiwan.

  • Page 4: Document Conventions

    Document Conventions Document Conventions Warnings and Notes These are how warnings and notes are shown in this User’s Guide. Warnings tell you about things that could harm you or your device. Notes tell you other important information (for example, other things you may need to configure or helpful tips) or recommendations.
  • Page 5 Icons Used in Figures Figures in this User’s Guide may use the following generic icons. The ZyXEL Device icon is not an exact representation of your device. ZyXEL Device Server Telephone P-2302HWUDL-P1 Series User’s Guide Computer Notebook computer DSLAM Firewall Switch Router Document Conventions...

  • Page 6: Safety Warnings

    Safety Warnings For your safety, be sure to read and follow all warning notices and instructions. • Do NOT use this product near water, for example, in a wet basement or near a swimming pool. • Do NOT expose your device to dampness, dust or corrosive liquids. •...
  • Page 7 Safety Warnings This product is recyclable. Dispose of it properly. P-2302HWUDL-P1 Series User’s Guide...
  • Page 8 Safety Warnings P-2302HWUDL-P1 Series User’s Guide...

  • Page 9: Table Of Contents

    Introduction, Wizards and Status ... 31 Introducing the ZyXEL Device ... 33 Introducing the Web Configurator ... 39 Wizard Setup ... 47 Status Screens ... 67 Network ... 77 Wireless LAN ... 79 WAN ... 95 LAN ... 105 NAT ...117 VoIP ...
  • Page 10 Contents Overview Appendices and Index ... 285 P-2302HWUDL-P1 Series User’s Guide...

  • Page 11: Table Of Contents

    About This User's Guide ... 3 Document Conventions... 4 Safety Warnings... 6 Contents Overview ... 9 Table of Contents... 11 List of Figures ... 21 List of Tables... 27 Part I: Introduction, Wizards and Status... 31 Chapter 1 Introducing the ZyXEL Device ... 33 1.1 Overview ...
  • Page 12 Table of Contents Chapter 3 Wizard Setup ... 47 3.1 Main Wizard Screen ... 47 3.2 Connection Wizard ... 48 3.2.1 Welcome ... 49 3.2.2 System Information ... 49 3.2.3 ISP Parameters ... 50 3.2.4 Your IP Address ... 52 3.2.5 WAN IP Address Assignment ...
  • Page 13 5.3 Additional Wireless Terms ... 82 5.4 General WLAN Screen ... 82 5.4.1 No Security ... 83 5.4.2 WEP Encryption Screen ... 84 5.4.3 WPA(2)-PSK ... 85 5.4.4 WPA(2) Authentication Screen ... 87 5.5 OTIST Screen ... 88 5.5.1 Notes on OTIST ... 90 5.6 MAC Filter ...
  • Page 14 Table of Contents Chapter 8 NAT... 117 8.1 NAT Overview ...117 8.1.1 Port Forwarding: Services and Port Numbers ...117 8.1.2 Trigger Port Forwarding ...118 8.1.3 SIP ALG ...119 8.2 NAT Screens ...119 8.2.1 NAT General Screen ...119 8.2.2 NAT Port Forwarding Screen ... 120 8.2.3 NAT Port Forwarding Edit Screen ...
  • Page 15 10.2 Phone Screens ... 144 10.2.1 Analog Phone Screen ... 144 10.2.2 Advanced Analog Phone Setup Screen ... 145 10.3 DECT Base Station Overview ... 147 10.3.1 DECT Phone Registration ... 147 10.3.2 Using your DECT Phone ... 149 10.3.3 DECT Phone Screen ... 150 10.3.4 Common Phone Settings Screen ...
  • Page 16 Table of Contents 13.9.3 Configuration Details: Incoming ... 174 13.9.4 Call Progression ... 175 Part IV: Security ... 177 Chapter 14 Firewall... 179 14.1 Firewall Overview ... 179 14.1.1 Stateful Inspection Firewall..179 14.1.2 About the ZyXEL Device Firewall ... 179 14.1.3 Guidelines For Enhancing Security With Your Firewall ...
  • Page 17 17.1.3 Application-based Bandwidth Management ... 198 17.1.4 Subnet-based Bandwidth Management ... 198 17.1.5 Application- and Subnet-based Bandwidth Management ... 198 17.1.6 Scheduler ... 198 17.1.7 Maximize Bandwidth Usage ... 199 17.1.8 Bandwidth Borrowing ... 201 17.1.9 Over Allotment of Bandwidth ... 202 17.2 Bandwidth Management Screens ...
  • Page 18 Table of Contents 20.1 Overview ... 229 20.2 Requirements ... 229 20.3 Configure a TCP/IP Printer Port ... 230 20.4 Print Server Screen ... 234 20.5 Adding a New Printer Example ... 235 20.6 Macintosh OS X Adding Printer Example ... 240 Chapter 21 File Sharing ...
  • Page 19 23.2 Logs Screens ... 262 23.2.1 View Log Screen ... 262 23.2.2 Log Settings Screen ... 263 23.3 Log Message Descriptions ... 265 Chapter 24 Tools... 273 24.1 Tools Overview ... 273 24.1.1 ZyXEL Firmware ... 273 24.2 Tools Screens ... 273 24.2.1 Firmware Screen ...
  • Page 20 Table of Contents Appendix G Services... 339 Appendix H Legal Information ... 343 Appendix I Customer Support ... 347 Index... 351 P-2302HWUDL-P1 Series User’s Guide...

  • Page 21: List Of Figures

    List of Figures List of Figures Figure 1 ZyXEL Device’s VoIP Features ... 33 Figure 2 ZyXEL Device as a VoIP Trunking Gateway ... 34 Figure 3 DECT Base Station Feature ... 34 Figure 4 File Sharing Overview ... 35 Figure 5 ZyXEL Device’s Router Features ...
  • Page 22 List of Figures Figure 39 Wireless: Static WEP Encryption ... 85 Figure 40 Wireless: WPA(2)-PSK ... 86 Figure 41 Wireless: WPA(2) ... 87 Figure 42 Network > Wireless LAN > OTIST ... 88 Figure 43 Example: Wireless Client OTIST Screen ... 89 Figure 44 OTIST: Settings ...
  • Page 23 List of Figures Figure 82 VoIP > Phone > DECT Phone ... 151 Figure 83 VoIP > Phone > Common ... 152 Figure 84 VoIP > Phone > Region ... 152 Figure 85 VoIP > Phone Book > Incoming Call Policy ... 155 Figure 86 VoIP >...
  • Page 24 List of Figures Figure 125 Management > Remote MGMT > Security ... 215 Figure 126 Add/Remove Programs: Windows Setup: Communication ... 218 Figure 127 Add/Remove Programs: Windows Setup: Communication: Components ... 219 Figure 128 Network Connections ... 219 Figure 129 Windows Optional Networking Components Wizard ... 220 Figure 130 Networking Services ...
  • Page 25 List of Figures Figure 168 Printer Model ... 242 Figure 169 Print Server ... 242 Figure 170 File Sharing Overview ... 243 Figure 171 Check the Workgroup Name ... 245 Figure 172 File Sharing Login ... 245 Figure 173 Management > File Sharing ... 246 Figure 174 File Sharing via Windows Explorer ...
  • Page 26 List of Figures Figure 211 Windows XP: Control Panel ...311 Figure 212 Windows XP: Control Panel: Network Connections: Properties ... 312 Figure 213 Windows XP: Local Area Connection Properties ... 312 Figure 214 Windows XP: Internet Protocol (TCP/IP) Properties ... 313 Figure 215 Windows XP: Advanced TCP/IP Properties ...

  • Page 27: List Of Tables

    List of Tables List of Tables Table 1 LED Descriptions ... 37 Table 2 Web Configurator Icons in the Title Bar ... 43 Table 3 Navigation Panel Summary ... 43 Table 4 Main Wizard Screen ... 48 Table 5 Connection Wizard > Welcome ... 49 Table 6 Connection Wizard >...
  • Page 28 List of Tables Table 39 Network > WAN > Internet Connection (Ethernet) ... 98 Table 40 Network > WAN > Internet Connection (Roadrunner) ... 99 Table 41 Network > WAN > Internet Connection (PPPoE) ... 100 Table 42 Network > WAN > Advanced ... 102 Table 43 Network >...
  • Page 29 List of Tables Table 82 Management > Static Route > IP Static Route ... 194 Table 83 Management > Static Route > IP Static Route > Edit ... 195 Table 84 Application and Subnet-based Bandwidth Management Example ... 198 Table 85 Maximize Bandwidth Usage Example ... 199 Table 86 Priority-based Allotment of Unused &...
  • Page 30 List of Tables Table 125 RTP Logs ... 271 Table 126 Lifeline Logs ... 271 Table 127 Maintenance > Tools > Firmware ... 274 Table 128 Maintenance > Tools > Configuration ... 275 Table 129 Device Specifications ... 287 Table 130 Firmware Features ... 288 Table 131 Feature Specifications ...

  • Page 31: Introduction, Wizards And Status

    Introduction, Wizards and Status Introducing the ZyXEL Device (33) Introducing the Web Configurator (39) Wizard Setup (47) Status Screens (67)

  • Page 33: Introducing The Zyxel Device

    H A P T E R Introducing the ZyXEL Device This chapter introduces the main applications and features of the ZyXEL Device. Overview This user’s guide explains how to configure the following ZyXEL devices: • The P-2302HWUD-P1 is a 4-port wireless router with Voice over IP (VoIP) communication capabilities that allow you to use a traditional analog telephone to make Internet calls.

  • Page 34: Voip Trunking Gateway

    Chapter 1 Introducing the ZyXEL Device 1.1.2 VoIP Trunking Gateway VoIP trunking allows you to use your ZyXEL Device as a gateway between VoIP and PSTN networks. Figure 2 ZyXEL Device as a VoIP Trunking Gateway In this example, you use your analog phone (A) to call the ZyXEL Device (B). The ZyXEL Device changes the call into VoIP and sends it via the Internet to another VoIP phone(C).

  • Page 35: Zyxel Device's Usb Support

    1.1.4 ZyXEL Device’s USB Support Use the built-in USB 2.0 ports to share files via a USB memory stick or a USB hard drive (A). You can also add a printer (B) and make it available on your local area network. Figure 4 File Sharing Overview 1.1.5 ZyXEL Device’s Router Features Your ZyXEL Device provides shared Internet access through your existing Internet access...

  • Page 36: Ways To Manage The Zyxel Device

    Chapter 1 Introducing the ZyXEL Device Use content filtering to block access to specific web sites, with URL’s containing keywords that you specify. You can define time periods and days during which content filtering is enabled and include or exclude particular computers on your network from content filtering. For example, you could block access to certain web sites for the kids.

  • Page 37: Figure 6 Leds

    Figure 6 LEDs None of the LEDs are on if the ZyXEL Device is not receiving power. Table 1 LED Descriptions COLOR STATUS POWER Green ETHERNET Green WLAN Green P-2302HWUDL-P1 Series User’s Guide Chapter 1 Introducing the ZyXEL Device DESCRIPTION The ZyXEL Device is receiving power and ready for use.
  • Page 38 Chapter 1 Introducing the ZyXEL Device Table 1 LED Descriptions COLOR STATUS Green INTERNET Green USB 2.0 Green PHONE 1-2 Green Orange DESCRIPTION The ZyXEL Device has an Ethernet connection with the cable/ DSL modem. Blinking The ZyXEL Device is sending/receiving data to /from the cable/ DSL modem.

  • Page 39: Introducing The Web Configurator

    H A P T E R This chapter describes how to access the ZyXEL Device web configurator and provides an overview of its screens. 2.1 Web Configurator Overview The web configurator is an HTML-based management interface that allows easy ZyXEL Device setup and management via Internet browser.

  • Page 40: Figure 7 Login Screen

    Chapter 2 Introducing the Web Configurator Figure 7 Login Screen 4 Type "1234" (default) as the password, and click Login. In some versions, the default password appears automatically - if this is the case, click Login. The Change Password screen appears. Figure 8 Change Password Screen 5 It is highly recommended to change your password.

  • Page 41: Resetting The Zyxel Device

    Figure 9 Select Mode Screen 6 In the Options screen, • Click Go to Wizard setup if you are logging in for the first time or if you want to make basic changes. See • Click Go to Advanced setup if you want to configure features that are not available in the wizards.

  • Page 42: Reset Button And Wlan

    Chapter 2 Introducing the Web Configurator 1 Make sure the POWER LED is on and not blinking. ress and hold the RESET button for ten seconds. Release the RESET button when the POWER LED begins to blink. The default settings have been restored. If the ZyXEL Device restarts automatically, wait for the ZyXEL Device to finish restarting, and log in to the web configurator.

  • Page 43: Title Bar

    2.4.1 Title Bar The title bar provides some icons in the upper right corner. The icons provide the following functions. Table 2 Web Configurator Icons in the Title Bar ICON DESCRIPTION Wizards: Click this icon to open one of the web configurator wizards. See on page 47 Logout: Click this icon to log out of the web configurator.
  • Page 44 Chapter 2 Introducing the Web Configurator Table 3 Navigation Panel Summary LINK General Port Forwarding Trigger Port VoIP SIP Settings Phone Analog Phone DECT Phone Common Region Phone Book Incoming Call Policy Speed Dial PSTN Line General Trunking General Peer Call Call Rule Security Firewall...

  • Page 45: Main Window

    Table 3 Navigation Panel Summary LINK Remote MGMT WWW Telnet SNMP Security Print Server General File Sharing General UPnP General Maintenance System General Dynamic DNS Time Setting Logs View Log Log Settings Tools Firmware Configuration Restart 2.4.3 Main Window The main window shows the screen you select in the navigation panel. It is discussed in more detail in the rest of this document.
  • Page 46 Chapter 2 Introducing the Web Configurator P-2302HWUDL-P1 Series User’s Guide...

  • Page 47: Wizard Setup

    H A P T E R This chapter provides information on the wizards in the web configurator. 3.1 Main Wizard Screen Use this screen to open one of the wizards in the ZyXEL Device. To access this screen, click Go to Wizard setup in the Login Options screen, or click the Wizard icon in the upper right corner of the main screen.

  • Page 48: Connection Wizard

    Chapter 3 Wizard Setup The following table describes the labels in this screen. Table 4 Main Wizard Screen LABEL DESCRIPTION CONNECTION Click this to open the Connection Wizard. See WIZARD VOIP SETUP Click this to open the VoIP Setup Wizard. See BANDWIDTH Click this to open the Bandwidth Management Wizard.

  • Page 49: Welcome

    3.2.1 Welcome Figure 12 Connection Wizard > Welcome The following table describes the labels in this screen. Table 5 Connection Wizard > Welcome LABEL DESCRIPTION < Back Click this to go to the previous screen. Next > Click this to go to the next screen. Exit Click this to close this screen and return to the main screen.

  • Page 50: Isp Parameters

    Chapter 3 Wizard Setup The following table describes the labels in this screen. Table 6 Connection Wizard > System Information LABEL DESCRIPTION System Name Enter your computer's "Computer Name". See information. This is for identification purposes, but some ISPs also check this field. This name can be up to 30 alphanumeric characters long.

  • Page 51: Figure 15 Connection Wizard > Isp Parameters (Pppoe)

    Table 7 Connection Wizard > ISP Parameters (Ethernet) LABEL DESCRIPTION Next > Click this to go to the next screen. Exit Click this to close this screen and return to the main screen. 3.2.3.2 PPPoE Point-to-Point Protocol over Ethernet (PPPoE) functions as a dial-up connection. PPPoE is an IETF (Internet Engineering Task Force) standard specifying how a host personal computer interacts with a broadband modem (for example DSL, cable, wireless, etc.) to achieve access to high-speed data networks.

  • Page 52: Your Ip Address

    Chapter 3 Wizard Setup 3.2.4 Your IP Address Figure 16 Connection Wizard > IP Address The following table describes the labels in this screen. Table 9 Connection Wizard > IP Address LABEL DESCRIPTION Get automatically Select this if your ISP did not assign you a static IP address. from your ISP Use fixed IP Select this if your ISP assigned you a static IP address.

  • Page 53: Figure 17 Connection Wizard > Ip Address (Ethernet)

    3.2.5.1 Ethernet Figure 17 Connection Wizard > IP Address (Ethernet) The following table describes the labels in this screen. Table 10 Connection Wizard > IP Address (Ethernet) LABEL DESCRIPTION My WAN IP Enter the IP address provided by your ISP. Address My WAN IP Enter the subnet mask provided by your ISP.

  • Page 54: Figure 18 Connection Wizard > Ip Address (Pppoe)

    Chapter 3 Wizard Setup Table 10 Connection Wizard > IP Address (Ethernet) LABEL DESCRIPTION < Back Click this to go to the previous screen. Next > Click this to go to the next screen. Exit Click this to close this screen and return to the main screen. 3.2.5.2 PPPoE You cannot use the discovered automatically.

  • Page 55: Mac Address

    The following table describes the labels in this screen. Table 11 Connection Wizard > IP Address (PPPoE) LABEL DESCRIPTION My WAN IP Enter the IP address provided by your ISP. Address First DNS Server Select From ISP if your ISP dynamically assigns DNS server information. (In this case, the ISP assigns the WAN IP address too.

  • Page 56: Finish

    Chapter 3 Wizard Setup The following table describes the labels in this screen. Table 12 Connection Wizard > MAC Address LABEL DESCRIPTION Factory default Select this if you want to use the default MAC address for the ZyXEL Device. Spoof this Select this if you do not want to use the default MAC address for the ZyXEL computer’s MAC Device.

  • Page 57: Voip Setup Wizard

    The following table describes the labels in this screen. Table 13 Connection Wizard > Finish LABEL DESCRIPTION Go to Bandwidth Click this to start the Bandwidth Management Wizard. See Management Wizard (optional) Finish Click this to close this screen and return to the main screen. 3.3 VoIP Setup Wizard Use this wizard to set up your VoIP account(s).

  • Page 58: Registration Complete

    Chapter 3 Wizard Setup The following table describes the labels in this screen. Table 14 VoIP Setup Wizard > SIP Settings LABEL DESCRIPTION SIP1 Settings SIP2 Settings SIP Number Enter your SIP number. In the full SIP URI (like 1234@VoIP-provider.com), this is the part before the @ symbol.

  • Page 59: Figure 23 Voip Setup Wizard > Registration Complete (Success)

    Figure 23 VoIP Setup Wizard > Registration Complete (Success) The following table describes the labels in this screen. Table 15 VoIP Setup Wizard > Registration Complete (Success) LABEL DESCRIPTION Return to Wizard Click this to open the main wizard screen. See Main Page Go to Advanced Click this to close this screen and return to the main screen.

  • Page 60: Bandwidth Management Wizard

    Chapter 3 Wizard Setup Figure 24 VoIP Setup Wizard > Registration Complete (Fail) The following table describes the labels in this screen. Table 16 VoIP Setup Wizard > Registration Complete (Fail) LABEL DESCRIPTION < Back Click this to go to the previous screen. Register Again Click this if you want the ZyXEL Device to try to register your SIP account(s) again.

  • Page 61: Welcome

    3.4.1 Welcome Figure 25 Bandwidth Management Wizard > Welcome The following table describes the labels in this screen. Table 17 Bandwidth Management Wizard > Welcome LABEL DESCRIPTION < Back Click this to go to the previous screen. Next > Click this to go to the next screen. Exit Click this to close this screen and return to the main screen.

  • Page 62: General Information

    Chapter 3 Wizard Setup 3.4.2 General Information Figure 26 Bandwidth Management Wizard > General Information The following table describes the labels in this screen. Table 18 Bandwidth Management Wizard > General Information LABEL DESCRIPTION Active Select this to enable bandwidth management. Bandwidth management applies to all traffic flowing through the router.

  • Page 63: Services Setup

    3.4.3 Services Setup Figure 27 Bandwidth Management Wizard > Services Setup The following table describes the labels in this screen. Table 19 Bandwidth Management Wizard > Services Setup LABEL DESCRIPTION Service Select the service(s) that should have higher priority when bandwidth is allocated. If you do not select a service or if you do not see it in the list, the service can still use bandwidth.

  • Page 64: Priority Setup

    Chapter 3 Wizard Setup 3.4.4 Priority Setup Figure 28 Bandwidth Management Wizard > Priority Setup The following table describes the labels in this screen. Table 20 Bandwidth Management Wizard > Priority Setup LABEL DESCRIPTION Service This column displays each service you selected in the previous screen. Priority Set the priority of each service.

  • Page 65: Finish

    3.4.5 Finish Figure 29 Bandwidth Management Wizard > Finish The following table describes the labels in this screen. Table 21 Bandwidth Management Wizard > Finish LABEL DESCRIPTION Finish Click this to close this screen and return to the main screen. P-2302HWUDL-P1 Series User’s Guide Chapter 3 Wizard Setup...
  • Page 66 Chapter 3 Wizard Setup P-2302HWUDL-P1 Series User’s Guide...

  • Page 67: Status Screens

    H A P T E R Use the Status screens to look at the current status of the device, system resources, interfaces (LAN and WAN), and SIP accounts. You can also register and unregister SIP accounts. The Status screen also provides detailed information from Any IP and DHCP and statistics from VoIP, bandwidth management, and traffic.

  • Page 68: Figure 30 Status Screen

    Chapter 4 Status Screens Figure 30 Status Screen Each field is described in the following table. Table 22 Status Screen LABEL DESCRIPTION Refresh Interval Enter how often you want the ZyXEL Device to update this screen. Refresh Now Click this to update this screen immediately. Device Information System Name...
  • Page 69 Table 22 Status Screen LABEL DESCRIPTION DHCP This field displays what DHCP services the ZyXEL Device is using in the WAN. Choices are: Client - The ZyXEL Device is a DHCP client in the WAN. Its IP address comes from a DHCP server on the WAN. None - The ZyXEL Device is not using any DHCP services in the WAN.
  • Page 70 Chapter 4 Status Screens Table 22 Status Screen LABEL DESCRIPTION Status This field indicates whether or not the ZyXEL Device is using the interface. Up - The ZyXEL Device is using the interface. Down - The ZyXEL Device is not using the interface. Rate If the interface uses Ethernet encapsulation, this column displays the port speed and the Ethernet duplex setting.

  • Page 71: Any Ip Table Window

    4.2 Any IP Table Window To access this screen, open the Status screen (see ...) next to Any IP Table. Figure 31 Any IP Table Window Each field is described in the following table. Table 23 Any IP Table Window LABEL DESCRIPTION This field is a sequential value.

  • Page 72: Voip Statistics Window

    Chapter 4 Status Screens Table 24 DHCP Table Window LABEL DESCRIPTION MAC Address This field displays the MAC address of the computer to which the ZyXEL Device assigned the IP address. Refresh Click this to update this screen. 4.4 VoIP Statistics Window To access this screen, open the Status screen (see ...) next to VoIP Statistics.

  • Page 73: Bw Mgmt Monitor Window

    Table 25 VoIP Statistics Window LABEL DESCRIPTION Protocol This field displays the transport protocol the SIP account is currently using. Message Waiting This field indicates whether or not there are any messages waiting for the SIP account. Last Incoming This field displays the last number that called the SIP account. It displays N/A if no Number number has ever dialed the SIP account.

  • Page 74: Figure 34 Bw Mgmt Monitor Window

    Chapter 4 Status Screens Figure 34 BW MGMT Monitor Window The types of traffic shown in this screen do not depend on your settings in the Management Wizard Table 26 BW MGMT Monitor Window LABEL DESCRIPTION LAN-VoIP (SIP) This field displays how much SIP traffic is going to the LAN each second. The rate is the number of kilobits that went to the LAN one second before the last time the screen updated (refreshed).

  • Page 75: Packet Statistics Window

    Table 26 BW MGMT Monitor Window LABEL DESCRIPTION Poll Interval Enter how often you want the ZyXEL Device to update this screen, and click Set Interval. Set Interval Click this to make the ZyXEL Device update the screen based on the amount of time you specified in Poll Interval.
  • Page 76 Chapter 4 Status Screens Table 27 Packet Statistics Window LABEL DESCRIPTION Rx Pkts This field displays the number of packets the ZyXEL Device has received from the port. Collisions This field displays the number of collisions detected by the port. Tx B/s This field displays how quickly the ZyXEL Device has transmitted packets from the port.

  • Page 77: Network

    Network Wireless LAN (79) WAN (95) LAN (105) NAT (117)

  • Page 79: Wireless Lan

    H A P T E R This chapter discusses how to configure the wireless network settings in your ZyXEL Device. See the appendices for more detailed information about wireless networks. 5.1 Wireless Network Overview The following figure provides an example of a wireless network. Figure 36 Example of a Wireless Network The wireless network is the part in the blue circle.

  • Page 80: Wireless Security Overview

    Chapter 5 Wireless LAN • Every device in the same wireless network must use security compatible with the AP. Security stops unauthorized devices from using the wireless network. It can also protect the information that is sent in the wireless network. 5.2 Wireless Security Overview The following sections introduce different types of wireless security you can set up in the wireless network.

  • Page 81: Encryption

    Unauthorized wireless devices can still see the information that is sent in the wireless network, even if they cannot use the wireless network. Furthermore, there are ways for unauthorized wireless users to get a valid user name and password. Then, they can use that user name and password to use the wireless network.

  • Page 82: One-Touch Intelligent Security Technology (Otist)

    Chapter 5 Wireless LAN 5.2.5 One-Touch Intelligent Security Technology (OTIST) With ZyXEL’s OTIST, you set up the SSID and the encryption (WEP or WPA-PSK) on the ZyXEL Device. Then, the ZyXEL Device transfers them to the devices in the wireless networks.

  • Page 83: No Security

    Figure 37 Wireless LAN: General The following table describes the general wireless LAN labels in this screen. Table 30 Wireless LAN: General LABEL DESCRIPTION Enable Click the check box to activate wireless LAN. Wireless LAN Name(SSID) (Service Set IDentity) The SSID identifies the Service Set with which a wireless station is associated.

  • Page 84: Wep Encryption Screen

    Chapter 5 Wireless LAN If you do not enable any wireless security on your ZyXEL Device, your network is accessible to any wireless networking device that is within range. Figure 38 Wireless: No Security The following table describes the labels in this screen. Table 31 Wireless No Security LABEL DESCRIPTION...

  • Page 85: Wpa(2)-Psk

    Figure 39 Wireless: Static WEP Encryption The following table describes the wireless LAN security labels in this screen. Table 32 Wireless: Static WEP Encryption LABEL DESCRIPTION Security Mode Choose Static WEP from the drop-down list box. Passphrase Enter a Passphrase (up to 32 printable characters) and clicking Generate. The ZyXEL Device automatically generates a WEP key.

  • Page 86: Figure 40 Wireless: Wpa(2)-Psk

    Chapter 5 Wireless LAN Figure 40 Wireless: WPA(2)-PSK The following table describes the wireless LAN security labels in this screen. Table 33 Wireless: WPA(2)-PSK LABEL DESCRIPTION Security Mode Choose WPA-PSK or WPA2-PSK from the drop-down list box. WPA Compatible This field is only available for WPA2-PSK. Select this if you want the ZyXEL Device to support WPA-PSK and WPA2-PSK simultaneously.

  • Page 87: Wpa(2) Authentication Screen

    5.4.4 WPA(2) Authentication Screen In order to configure and enable WPA Authentication; click the Wireless LAN link under Network to display the Wireless screen. Select WPA or WPA2 from the Security list. Figure 41 Wireless: WPA(2) The following table describes the wireless LAN security labels in this screen. Table 34 Wireless: WPA(2) LABEL DESCRIPTION...

  • Page 88: Otist Screen

    Chapter 5 Wireless LAN Table 34 Wireless: WPA(2) LABEL Group Key Update Timer Authentication Server IP Address Port Number Shared Secret Accounting Server (optional) IP Address Port Number Shared Secret 5.5 OTIST Screen Use this screen to set up and start OTIST on the ZyXEL Device in your wireless network.To open this screen, click Network >...

  • Page 89: Figure 43 Example: Wireless Client Otist Screen

    The following table describes the labels in this screen. Table 35 Network > Wireless LAN > OTIST LABEL Setup Key Yes! Start Before you click Start, you should enable OTIST on all the OTIST-enabled devices in the wireless network. For most devices, follow these steps. 1 Start the ZyXEL utility 2 Click the Adapter tab.

  • Page 90: Notes On Otist

    Chapter 5 Wireless LAN You must click Start in the ZyXEL Device and in the wireless device(s) within three minutes of each other. You can start OTIST in the wireless devices and the ZyXEL Device in any order. After you click Start in the ZyXEL Device, the following screen appears (in the ZyXEL Device).

  • Page 91: Mac Filter

    Figure 46 Start OTIST? 2 If an OTIST-enabled wireless device loses its wireless connection for more than ten seconds, it will search for an OTIST-enabled AP for up to one minute. (If you manually have the wireless device search for an OTIST-enabled AP, there is no timeout; click Cancel in the OTIST progress screen to stop the search.) 3 After the wireless device finds an OTIST-enabled AP, you must click Start in the ZyXEL Device’s Network >...

  • Page 92: Figure 47 Mac Address Filter

    Chapter 5 Wireless LAN Figure 47 MAC Address Filter The following table describes the labels in this menu. Table 36 MAC Address Filter LABEL DESCRIPTION Active Select the check box to enable MAC address filtering. Define the filter action for the list of MAC addresses in the MAC Address table. Filter Action Select Deny to block access to the ZyXEL Device, MAC addresses not listed will be allowed to access the ZyXEL Device...

  • Page 93: Wireless Lan Advanced Setup

    5.7 Wireless LAN Advanced Setup To configure advanced wireless settings, click the Advanced Setup button in the General screen. The screen appears as shown. Figure 48 Wireless LAN: Advanced The following table describes the labels in this screen. Table 37 Wireless LAN: Advanced LABEL DESCRIPTION Wireless Advanced Setup...
  • Page 94 Chapter 5 Wireless LAN P-2302HWUDL-P1 Series User’s Guide...

  • Page 95: Wan

    H A P T E R Use these screens to set up the ZyXEL Device on the WAN. You can configure the Internet connection, DNS servers, and how the ZyXEL Device sends routing information using RIP. In addition, you can set up a backup gateway in case the default gateway is not available. 6.1 WAN Overview 6.1.1 PPPoE Encapsulation The ZyXEL Device supports PPPoE (Point-to-Point Protocol over Ethernet).

  • Page 96: Mac Address

    Chapter 6 WAN You can obtain your IP address from the IANA, from an ISP or have it assigned by a private network. If you belong to a small organization and your Internet access is through an ISP, the ISP can provide you with the Internet addresses for your local networks. On the other hand, if you are part of a much larger organization, you should consult your network administrator for the appropriate IP addresses.

  • Page 97: Wan Screens

    2 If the ISP did not give you DNS server information, leave the DNS Server fields in the SYSTEM General screen set to 0.0.0.0 for the ISP to dynamically assign the DNS server IP addresses. 6.2 WAN Screens 6.2.1 WAN Internet Connection Screen (Ethernet) Use this screen to set up your Internet connection.

  • Page 98: Wan Internet Connection Screen (Roadrunner)

    Chapter 6 WAN Each field is described in the following table. Table 39 Network > WAN > Internet Connection (Ethernet) LABEL DESCRIPTION ISP Parameters for Internet Access Encapsulation Select Ethernet. Ethernet encapsulation with Service Type set to Standard is typically used if you are extending your existing network. Service Type Select Standard.

  • Page 99: Wan Internet Connection Screen (Pppoe)

    Figure 50 Network > WAN > Internet Connection (Roadrunner) Each field is described in the following table. Table 40 Network > WAN > Internet Connection (Roadrunner) LABEL DESCRIPTION ISP Parameters for Internet Access Encapsulation Select Ethernet. Service Type Select the Roadrunner service provided by your ISP. User Name Enter the user name provided by your ISP.

  • Page 100: Figure 51 Network > Wan > Internet Connection (Pppoe)

    Chapter 6 WAN Figure 51 Network > WAN > Internet Connection (PPPoE) Each field is described in the following table. Table 41 Network > WAN > Internet Connection (PPPoE) LABEL ISP Parameters for Internet Access Encapsulation Service Name User Name Password Retype to Confirm Retype your password to make sure you entered it correctly.

  • Page 101: Wan Advanced Screen

    Table 41 Network > WAN > Internet Connection (PPPoE) LABEL DESCRIPTION Get automatically Select this if your ISP did not assign you a static IP address. from ISP Use Fixed IP Select this if your ISP assigned you a static IP address. Address My WAN IP Enter the IP address provided by your ISP.

  • Page 102: Figure 52 Network > Wan > Advanced

    Chapter 6 WAN Figure 52 Network > WAN > Advanced Each field is described in the following table. Table 42 Network > WAN > Advanced LABEL DNS Servers First DNS Server Second DNS Server Third DNS Server RIP & Multicast Setup RIP Direction RIP Version...

  • Page 103: Wan Traffic Redirect Screen

    Table 42 Network > WAN > Advanced LABEL DESCRIPTION Multicast Select which version of IGMP the ZyXEL Device uses to support multicasting on the WAN. Multicasting sends packets to some computers on the WAN and is an alternative to unicasting (sending packets to one computer) and broadcasting (sending packets to every computer).

  • Page 104: Table 43 Network > Wan > Traffic Redirect

    Chapter 6 WAN Each field is described in the following table. Table 43 Network > WAN > Traffic Redirect LABEL Active Backup Gateway IP Address Check WAN IP Address Fail Tolerance Period (sec) Timeout (sec) Apply Cancel DESCRIPTION Select this to set up a backup gateway in case the default gateway is not available.

  • Page 105: Lan

    H A P T E R Use these screens to set up the ZyXEL Device on the LAN. You can configure its IP address and subnet mask, DHCP services, and other subnets. You can also control how the ZyXEL Device sends routing information using RIP, and you can enable and disable Any IP. 7.1 LAN Overview A Local Area Network (LAN) is a shared communication system to which many computers are attached.

  • Page 106: Dhcp Setup

    Chapter 7 LAN 7.1.2 DHCP Setup DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a server. You can configure the ZyXEL Device as a DHCP server or disable it. When configured as a server, the ZyXEL Device provides the TCP/IP configuration for the clients.

  • Page 107: Rip Setup

    Please note that DNS proxy works only when the ISP uses the IPCP DNS server extensions. It does not mean you can leave the DNS servers out of the DHCP setup under all circumstances. If your ISP gives you explicit DNS servers, make sure that you enter their IP addresses in the LAN Setup screen.

  • Page 108: Any Ip

    Chapter 7 LAN The ZyXEL Device supports both IGMP version 1 (IGMP-v1) and IGMP version 2 (IGMP- v2). At start up, the ZyXEL Device queries all directly connected networks to gather group membership. After that, the ZyXEL Device periodically updates this information. IP multicasting can be enabled/disabled on the ZyXEL Device LAN and/or WAN interfaces in the web configurator (LAN;...

  • Page 109: Lan Screens

    You must enable NAT to use the Any IP feature on the ZyXEL Device. Address Resolution Protocol (ARP) is a protocol for mapping an Internet Protocol address (IP address) to a physical machine address, also known as a Media Access Control or MAC address, on the local area network.

  • Page 110: Lan Dhcp Setup Screen

    Chapter 7 LAN Each field is described in the following table. Table 44 Network > LAN > IP LABEL IP Address IP Subnet Mask Apply Cancel 7.2.2 LAN DHCP Setup Screen Use this screen to enable, disable, and configure the DHCP server in the ZyXEL Device. To access this screen, click Network >...

  • Page 111: Lan Static Dhcp Screen

    Table 45 Network > LAN > DHCP Setup LABEL DESCRIPTION Pool Size Enter the number of IP addresses to allocate. This number must be at least one and is limited by a subnet mask of 255.255.255.0 (regardless of the subnet the ZyXEL Device is in).

  • Page 112: Lan Client List Screen

    Chapter 7 LAN Each field is described in the following table. Table 46 Network > LAN > Static DHCP LABEL MAC Address IP Address Apply Cancel 7.2.4 LAN Client List Screen This screen is empty if the DHCP server is not enabled. You can enable it in Network >...

  • Page 113: Lan Ip Alias Screen

    7.2.5 LAN IP Alias Screen Use this screen to add subnets on the LAN port. You can also control what routing information is sent and received by each subnet. To access this screen, click Network > LAN > IP Alias. Figure 59 Network >...

  • Page 114: Lan Advanced Screen

    Chapter 7 LAN Table 48 Network > LAN > IP Alias LABEL RIP Direction RIP Version Apply Cancel 7.2.6 LAN Advanced Screen Use this screen to add subnets on the LAN port. You can also control what routing information is sent and received by each subnet. To access this screen, click Network > LAN > Advanced.

  • Page 115: Table 49 Network > Lan > Advanced

    Each field is described in the following table. Table 49 Network > LAN > Advanced LABEL DESCRIPTION RIP & Multicast Setup RIP Direction Use this field to control how much routing information the ZyXEL Device sends and receives on the subnet. None - The ZyXEL Device does not send or receive routing information on the subnet.
  • Page 116 Chapter 7 LAN P-2302HWUDL-P1 Series User’s Guide...

  • Page 117: Nat

    H A P T E R Use these screens to configure port forwarding and trigger ports for the ZyXEL Device. You can also enable and disable SIP, FTP, and H.323 ALG. 8.1 NAT Overview 8.1.1 Port Forwarding: Services and Port Numbers A NAT server set is a list of inside (behind NAT on the LAN) servers, for example, web or FTP, that you can make accessible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world.

  • Page 118: Trigger Port Forwarding

    Chapter 8 NAT Figure 61 Multiple Servers Behind NAT Example 8.1.2 Trigger Port Forwarding Some services use a dedicated range of ports on the client side and a dedicated range of ports on the server side. With regular port forwarding you set a forwarding port in NAT to forward a service (coming in from the server on the WAN) to the IP address of a computer on the client side (LAN).

  • Page 119: Sip Alg

    2 Port 7070 is a “trigger” port and causes the ZyXEL Device to record Jane’s computer IP address. The ZyXEL Device associates Jane's computer IP address with the "incoming" port range of 6970-7170. 3 The Real Audio server responds using a port number ranging between 6970-7170. 4 The ZyXEL Device forwards the traffic to Jane’s computer IP address.

  • Page 120: Nat Port Forwarding Screen

    Chapter 8 NAT Each field is described in the following table. Table 50 Network > NAT > General LABEL NAT Setup Enable Network Address Translation Max NAT/Firewall Session Per User Apply Cancel 8.2.2 NAT Port Forwarding Screen Use this screen to look at the current port-forwarding rules in the ZyXEL Device, and to enable, disable, activate, and deactivate each one.

  • Page 121: Nat Port Forwarding Edit Screen

    Each field is described in the following table. Table 51 Network > NAT > Port Forwarding LABEL DESCRIPTION Default Server Setup Default Server Enter the IP address of the server to which the ZyXEL Device should forward packets for ports that are not specified in the Port Forwarding section below or in the Management >...

  • Page 122: Nat Trigger Port Screen

    Chapter 8 NAT Each field is described in the following table. Table 52 Network > NAT > Port Forwarding > Edit LABEL Active Service Name Start Port End Port Server IP Address Enter the IP address of the server to which to forward packets for the selected port Apply Cancel 8.2.4 NAT Trigger Port Screen...

  • Page 123: Nat Alg Screen

    Each field is described in the following table. Table 53 Network > NAT > Trigger Port LABEL DESCRIPTION Name Enter a name to identify this rule. You can use 1 - 15 printable ASCII characters, or you can leave this field blank. It does not have to be a unique name. Incoming Start Port Enter the incoming port number or range of port numbers you want to forward to...
  • Page 124 Chapter 8 NAT Table 54 Network > NAT > ALG LABEL Enable H.323 Apply Cancel DESCRIPTION Select this to make sure H.323 (audio-visual programs, such as NetMeeting) works correctly with port-forwarding and port-triggering rules. Click this to save your changes and to apply them to the ZyXEL Device. Click this to discard your most recent changes.

  • Page 125: Voip

    VoIP SIP (127) Phone (141) Phone Book (155) PSTN Line (159) VoIP Trunking (161)

  • Page 127: Sip

    H A P T E R Use these screens to set up your SIP accounts and to configure QoS settings. 9.1 SIP Overview 9.1.1 Introduction to VoIP VoIP (Voice over IP) is the sending of voice signals over the Internet Protocol. This allows you to make phone calls and send faxes over the Internet at a fraction of the cost of using the traditional circuit-switched telephone network.

  • Page 128: Sip Call Progression

    Chapter 9 SIP 9.1.3.2 SIP Service Domain The SIP service domain of the VoIP service provider (the company that lets you make phone calls over the Internet) is the domain name in a SIP URI. For example, if the SIP address is 1122334455@VoIP-provider.com, then “VoIP-provider.com”...

  • Page 129: Figure 68 Sip User Agent

    Figure 68 SIP User Agent 9.1.5.2 SIP Proxy Server A SIP proxy server receives requests from clients and forwards them to another server. In the following example, you want to use client device A to call someone who is using client device C.

  • Page 130: Rtp

    Chapter 9 SIP Figure 70 SIP Redirect Server 9.1.5.4 SIP Register Server A SIP register server maintains a database of SIP identity-to-IP address (or domain name) mapping. The register server checks your user name and password when you register. 9.1.6 RTP When you make a VoIP call using SIP, the RTP (Real time Transport Protocol) is used to handle voice data transfer.

  • Page 131: Voice Coding

    9.1.7.2 Use NAT If you know the NAT router’s public IP address and SIP port number, you can use the Use NAT feature to manually configure the ZyXEL Device to use a them in the SIP messages. This eliminates the need for STUN or a SIP ALG. You must also configure the NAT router to forward traffic with this port number to the ZyXEL Device.

  • Page 132: Pstn Call Setup Signaling

    Chapter 9 SIP • G.729 is an Analysis-by-Synthesis (AbS) hybrid waveform codec that uses a filter based on information about how the human vocal tract produces sounds. G.729 provides good sound quality and reduces the required bandwidth to 8kbps. 9.1.9 PSTN Call Setup Signaling PSTNs (Public Switched Telephone Networks) use DTMF or pulse dialing to set up telephone calls.

  • Page 133: Quality Of Service (Qos)

    9.2.0.2 Listening to Custom Tones Do the following to listen to a custom tone: 1 Pick up the phone and press “****” on your phone’s keypad and wait for the message that says you are in the configuration menu. 2 Press a number from 1201~1208 followed by the “#” key to listen to the tone. 3 You can continue to add, listen to, or delete tones, or you can hang up the receiver when you are done.

  • Page 134: Sip Screens

    Chapter 9 SIP DSCP is backward compatible with the three precedence bits in the ToS octet so that non- DiffServ compliant, ToS-enabled network device will not conflict with the DSCP mapping. The DSCP value determines the forwarding behavior, the PHB (Per-Hop Behavior), that each packet gets across the DiffServ network.

  • Page 135: Advanced Sip Setup Screen

    Each field is described in the following table. Table 57 VoIP > SIP > SIP Settings LABEL DESCRIPTION SIP Account Select the SIP account you want to see in this screen. If you change this field, the screen automatically refreshes. SIP Settings Active SIP Select this if you want the ZyXEL Device to use this account.

  • Page 136: Figure 74 Voip > Sip > Sip Settings > Advanced

    Chapter 9 SIP Figure 74 VoIP > SIP > SIP Settings > Advanced P-2302HWUDL-P1 Series User’s Guide...

  • Page 137: Table 58 Voip > Sip > Sip Settings > Advanced

    Each field is described in the following table. Table 58 VoIP > SIP > SIP Settings > Advanced LABEL DESCRIPTION SIP Account This field displays the SIP account you see in this screen. SIP Server Settings URL Type Select whether or not to include the SIP service domain name when the ZyXEL Device sends the SIP number.
  • Page 138 Chapter 9 SIP Table 58 VoIP > SIP > SIP Settings > Advanced LABEL DTMF Mode STUN Active Server Address Server Port Use NAT Active Server Address Server Port Outbound Proxy Active Server Address Server Port NAT Keep Alive Active Keep Alive with SIP Proxy Keep Alive with...

  • Page 139: Sip Qos Screen

    Table 58 VoIP > SIP > SIP Settings > Advanced LABEL DESCRIPTION Enable Select this if you want to hear a waiting (beeping) dial tone on your phone when you have at least one voice message. Your VoIP service provider must support this feature.

  • Page 140: Figure 75 Voip > Sip > Qos

    Chapter 9 SIP Figure 75 VoIP > SIP > QoS Each field is described in the following table. Table 59 VoIP > SIP > QoS LABEL SIP TOS Priority Setting RTP TOS Priority Setting Voice VLAN ID Apply Cancel DESCRIPTION Enter the priority for SIP voice transmissions.

  • Page 141: Phone

    H A P T E R The following sections describe how to configure the ZyXEL Device to work with analog phones and how to configure the ZyXEL Device’s built in DECT base station to work with DECT phones. 10.1 Analog Phone Overview You can configure the volume, echo cancellation and VAD settings for each individual phone port on the ZyXEL Device.

  • Page 142: Table 60 European Type Flash Key Commands

    Chapter 10 Phone To take full advantage of the supplementary phone services available though the ZyXEL Device's phone ports, you may need to subscribe to the services from your VoIP service provider. 10.1.3.1 The Flash Key Flashing means to press the hook for a short period of time (a few hundred milliseconds) before releasing it.

  • Page 143: Table 61 Usa Type Flash Key Commands

    10.1.3.2.2 European Call Waiting This allows you to place a call on hold while you answer another incoming call on the same telephone (directory) number. If there is a second call to a telephone number, you will hear a call waiting tone. Take one of the following actions.

  • Page 144: Phone Screens

    Chapter 10 Phone 10.1.3.3.1 USA Call Hold Call hold allows you to put a call (A) on hold by pressing the flash key. If you have another call, press the flash key to switch back and forth between caller A and B by putting either one on hold.

  • Page 145: Advanced Analog Phone Setup Screen

    Figure 76 VoIP > Phone > Analog Phone Each field is described in the following table. Table 62 VoIP > Phone > Analog Phone LABEL DESCRIPTION Phone Port Select the phone port you want to see in this screen. If you change this field, the Settings screen automatically refreshes.

  • Page 146: Figure 77 Voip > Phone > Analog Phone > Advanced

    Chapter 10 Phone Figure 77 VoIP > Phone > Analog Phone > Advanced Each field is described in the following table. Table 63 VoIP > Phone > Analog Phone > Advanced LABEL Analog Phone Voice Volume Control Speaking Volume Listening Volume Echo Cancellation G.168 Active Dialing Interval...

  • Page 147: Dect Base Station Overview

    10.3 DECT Base Station Overview Your ZyXEL Device has a built in Digital Enhanced Cordless Telecommunications (DECT) base station. DECT is an ETSI (European Telecommunications Standards Institute) standard for digital cordless phones which specifies how they transmit, receive and process data and voice communication.

  • Page 148: Figure 79 Dect Base Station Button - Top Of The Zyxel Device

    Chapter 10 Phone Figure 79 DECT Base Station Button - Top of the ZyXEL Device 2 Put your DECT phone in registration mode. Refer to your DECT phone documentation. When the ZyXEL Device is in registration mode, it scans its surrounding area for DECT phones in registration mode.

  • Page 149: Using Your Dect Phone

    10.3.1.1 DECT Base Station Reset Resetting the DECT base station erases all the details of the DECT phones registered with the ZyXEL Device. You can do this to clear the DECT base station memory of the DECT phones no longer used with the ZyXEL Device, for example if one of your DECT phones is lost. When you reset the DECT base station, you will need to re-register all the phones that you want to use with the ZyXEL Device.

  • Page 150: Dect Phone Screen

    Chapter 10 Phone Table 64 DECT Phone Calls Summary TYPE OF CALL DESCRIPTION 3 Way A call between two DECT phones Conference registered with the ZyXEL Device base station and an external connection. The ZyXEL Device allows up to four DECT phones to be active at one time. The ZyXEL Device does not control how your DECT phone distinguishes between internal and external calls.

  • Page 151: Figure 82 Voip > Phone > Dect Phone

    Figure 82 VoIP > Phone > DECT Phone Each field is described in the following table. Table 65 VoIP > Phone > DECT Phone LABEL DESCRIPTION Outgoing Call Use If you select both SIP accounts, the ZyXEL Device tries to use the most recently registered SIP account first.

  • Page 152: Common Phone Settings Screen

    Chapter 10 Phone Table 65 VoIP > Phone > DECT Phone LABEL Retype to Confirm Apply Cancel 10.3.4 Common Phone Settings Screen Use this screen to activate and deactivate immediate dialing. To access this screen, click VoIP > Phone > Common. Figure 83 VoIP >...

  • Page 153: Table 67 Voip > Phone > Region

    Each field is described in the following table. Table 67 VoIP > Phone > Region LABEL DESCRIPTION Region Settings Select the place in which the ZyXEL Device is located. Do not select Default. Call Service Mode Select the mode for supplementary phone services (call hold, call waiting, call transfer and three-way conference calls) that your VoIP service provider supports.
  • Page 154 Chapter 10 Phone P-2302HWUDL-P1 Series User’s Guide...

  • Page 155: Phone Book

    H A P T E R Use these screens to maintain call-forwarding rules and speed-dial settings. 11.1 Phone Book Screens 11.1.1 Incoming Call Policy Screen Use this screen to maintain rules for handling incoming calls. You can block, redirect, or accept them.

  • Page 156: Table 68 Voip > Phone Book > Incoming Call Policy

    Chapter 11 Phone Book You can create two sets of call-forwarding rules. Each one is stored in a call-forwarding table. Each field is described in the following table. Table 68 VoIP > Phone Book > Incoming Call Policy LABEL Table Number Forward to Number Setup Unconditional...

  • Page 157: Speed Dial Screen

    11.1.2 Speed Dial Screen Speed dial provides shortcuts for dialing frequently used (VoIP) phone numbers. You also have to create speed-dial entries if you want to make peer-to-peer calls or call SIP numbers that use letters. Use this screen to add, edit, or remove speed-dial entries. To access this screen, click VoIP >...
  • Page 158 Chapter 11 Phone Book Table 69 VoIP > Phone Book > Speed Dial LABEL Type Speed Dial Phone Book Speed Dial Number Name Destination Modify Clear Cancel DESCRIPTION Select Use Proxy if you want to use one of your SIP accounts to call this phone number.

  • Page 159: Pstn Line

    H A P T E R This chapter applies to “L” models only. Use this screen to set up the PSTN line used to make regular phone calls. These phone calls do not use the Internet. 12.1 PSTN Line Overview With the Public Switched Telephone Network (PSTN) line, you can make and receive regular phone calls.

  • Page 160: Figure 86 Voip > Pstn Line > General

    Chapter 12 PSTN Line Figure 86 VoIP > PSTN Line > General Each field is described in the following table. Table 70 VoIP > PSTN Line > General LABEL PSTN Line Pre-fix Number Relay to PSTN Line Apply Cancel DESCRIPTION Enter 1 - 7 telephone keys (0 - 9, #, *) you dial before you dial the phone number, if you want to make a regular phone call while one of your SIP accounts is registered.

  • Page 161: Voip Trunking

    H A P T E R Use these screens to configure VoIP trunking on your ZyXEL Device. 13.1 VoIP Trunking Overview VoIP trunking connects an IP network (like the Internet) and the Public Switched Telephone Network (PSTN). PSTN includes the world’s circuit-switched telephone network which is composed of fixed and mobile telephones.

  • Page 162: Peer Call Authentication

    Chapter 13 VoIP Trunking Other settings controlled by the auto attendant include a time limit to decide whether you want to forward a call from the ZyXEL Device or call the phone directly connected to the ZyXEL Device. When you call into your ZyXEL Device you can request to forward a call to another phone number simply by dialing that number.

  • Page 163: Call Rules

    13.3 Call Rules Call rules automate the forwarding of calls, first to a remote peer device and then to PSTN phones. This is used when you make frequent calls to several PSTN numbers in the same geographic area that start with the same numbers (for example an area code). If there is a remote peer device in that area, you can set up a VoIP link to it and have it forward the calls to PSTN phones.

  • Page 164: Pstn Phone To Pstn Phone Via Voip

    Chapter 13 VoIP Trunking Figure 89 PSTN Phone To VoIP Phone 13.4.3 PSTN Phone To PSTN Phone via VoIP A PSTN phone A makes a call to the ZyXEL Device B. B connects to a peer device C and C forwards the call to a PSTN phone D.

  • Page 165: Trunking Peer Call Screen

    Each field is described in the following table. Table 73 VoIP > Trunking > General LABEL DESCRIPTION Enable Trunking Select this to turn on VoIP trunking on your ZyXEL Device. Auto Attendant This is the setting which determines how long the ZyXEL Device waits for a caller Timeout(sec) to enter a phone number when it receives the call.

  • Page 166: Figure 92 Voip > Trunking > Peer Call

    Chapter 13 VoIP Trunking Figure 92 VoIP > Trunking > Peer Call Each field is described in the following table. Table 74 VoIP > Trunking > Peer Call LABEL Outgoing Authentication Name Username DESCRIPTION You need to set up accounts for the peer devices you use in VoIP trunking. This is the IP address of the remote peer device, as well as the username and password needed to authenticate with the remote peer device.

  • Page 167: Trunking Call Rule Screen

    Table 74 VoIP > Trunking > Peer Call LABEL DESCRIPTION Password Enter the corresponding password for the username you entered. The remote peer device must have the same password in an incoming authentication entry in order to authenticate your connection. Enter up to 32 alphanumeric characters. Peer IP Enter the IP address of the remote peer device which you want to connect to.

  • Page 168: Figure 93 Voip > Trunking > Call Rule

    Chapter 13 VoIP Trunking Figure 93 VoIP > Trunking > Call Rule Each field is described in the following table. Table 75 VoIP > Trunking > Call Rule LABEL Pattern Account Apply Cancel DESCRIPTION This is a read-only index number of the call rules. A Pattern is used when you call your ZyXEL Device from a PSTN phone and want to use it to create a VoIP link to a remote peer device which will forward the call to a PSTN phone.

  • Page 169: Voip Trunking Example: Voip To Pstn

    13.8 VoIP Trunking Example: VoIP to PSTN This example shows how to configure VoIP to PSTN trunking to save on long distance calls. 13.8.1 Background Information A company has its headquarters in city A and a branch office in city B. The headquarters often needs to call salespeople employed at the branch office.

  • Page 170: Configuration Details: Incoming

    Chapter 13 VoIP Trunking Figure 95 VoIP to PSTN Example - Speed Dial Screen 2 An outgoing authentication account needs to be configured. This account consists of the IP address and port number of the branch office ZyXEL Device as well as the username and password for authentication.

  • Page 171: Call Progression

    Figure 97 VoIP to PSTN Example - Incoming Authentication 13.8.4 Call Progression The advantage of this kind of VoIP trunking is that once all the configuration is completed, the caller just has to dial a speed dial entry from a phone connected to their ZyXEL Device and the peer devices take care of the rest.

  • Page 172: Background Information

    Chapter 13 VoIP Trunking 13.9.1 Background Information A company has its headquarters in two different cities. The sales manager (A) from headquarters often needs to call salespeople (D) employed at the branch office. The sales manager often works away from the headquarters office and the sales employees often work away from the branch office.

  • Page 173: Figure 99 Pstn To Pstn Example: General Configuration

    Figure 99 PSTN to PSTN Example: General Configuration 2 An outgoing authentication account needs to be configured. This account consists of the IP address and port number of the branch office ZyXEL Device as well as the username and password for authentication. This username and password must match the incoming authentication account username and password on the branch office ZyXEL Device.

  • Page 174: Configuration Details: Incoming

    Chapter 13 VoIP Trunking Figure 101 PSTN to PSTN Example - Call Rule 13.9.3 Configuration Details: Incoming The branch office ZyXEL Device needs to have an incoming authentication account configured. This consists of a username and password. This account must match the username and password of the outgoing authentication account of the headquarters’...

  • Page 175: Call Progression

    13.9.4 Call Progression The call is initiated by the manager dialing into the headquarter’s ZyXEL Device via PSTN. In this scenario a VoIP link is established between headquarters and the branch office and then the call is forwarded to Sales1 using PSTN. Table 77 PSTN to PSTN: VoIP Trunking Call Progression MANAGER HEADQUARTERS...
  • Page 176 Chapter 13 VoIP Trunking P-2302HWUDL-P1 Series User’s Guide...

  • Page 177: Security

    Security Firewall (179) Content Filter (187)

  • Page 179: Firewall

    H A P T E R Use these screens to enable, configure and disable the firewall that protects your ZyXEL Device and your LAN from unwanted or malicious traffic. 14.1 Firewall Overview Originally, the term firewall referred to a construction technique designed to prevent the spread of fire from one room to another.

  • Page 180: Guidelines For Enhancing Security With Your Firewall

    Chapter 14 Firewall The ZyXEL Device has one Ethernet WAN port and four Ethernet LAN ports, which are used to physically separate the network into two areas.The WAN (Wide Area Network) port attaches to the broadband (cable or DSL) modem to the Internet. The LAN (Local Area Network) port attaches to a network of computers, which needs security from the outside world.

  • Page 181: Triangle Route

    Blocked LAN-to-WAN packets are considered alerts. Alerts are “higher priority logs” that include system errors, attacks and attempted access to blocked web sites. Alerts appear in red in the View Log screen. You may choose to have alerts e-mailed immediately in the Log Settings screen.

  • Page 182: Solving The "Triangle Route" Problem

    Chapter 14 Firewall 2 The ZyXEL Device reroutes the SYN packet through Gateway A on the LAN to the WAN. 3 The reply from the WAN goes directly to the computer on the LAN without going through the ZyXEL Device. As a result, the ZyXEL Device resets the connection, as the connection has not been acknowledged.

  • Page 183: Firewall Screens

    Figure 106 IP Alias 14.3 Firewall Screens 14.3.1 General Firewall Screen Use this screen to configure the basic settings for your firewall. To access this screen, click Security > Firewall > General. Figure 107 Security > Firewall > General Each field is described in the following table. Table 78 Security >...

  • Page 184: Firewall Services Screen

    Chapter 14 Firewall Table 78 Security > Firewall > General LABEL Packet Direction Apply Cancel 14.3.2 Firewall Services Screen Use this screen to enable service blocking, to set up the date and time service blocking is effective, and to maintain the list of services you want to block. To access this screen, click Security >...
  • Page 185 Table 79 Security > Firewall > Services LABEL DESCRIPTION Available This is a list of pre-defined services (destination ports) you may prohibit your LAN Services computers from using. Select the port you want to block, and click Add to add the port to the Blocked Services field.
  • Page 186 Chapter 14 Firewall P-2302HWUDL-P1 Series User’s Guide...

  • Page 187: Content Filter

    H A P T E R Use these screens to create and enforce policies that restrict access to the Internet based on content. 15.1 Content Filtering Overview Internet content filtering allows you to create and enforce Internet access policies tailored to their needs.

  • Page 188: Figure 109 Security > Content Filter > Filter

    Chapter 15 Content Filter Figure 109 Security > Content Filter > Filter Each field is described in the following table. Table 80 Security > Content Filter > Filter LABEL Trusted IP Setup Trusted Computer IP Address Restrict Web Features Keyword Blocking Enable URL Keyword Blocking Keyword...

  • Page 189: Content Filter Schedule Screen

    Table 80 Security > Content Filter > Filter LABEL DESCRIPTION Keyword List This field displays the keywords that are blocked when Enable URL Keyword Blocking is selected. To delete a keyword, select it, click Delete, and click Apply. Delete Click Delete to remove the selected keyword in the Keyword List. The keyword disappears after you click Apply.
  • Page 190 Chapter 15 Content Filter P-2302HWUDL-P1 Series User’s Guide...

  • Page 191: Management

    Management Static Route (193) Bandwidth MGMT (197) Remote MGMT (209) UPnP (217) Sharing a USB Printer (229) File Sharing (243)

  • Page 193: Static Route

    H A P T E R Use these screens to configure static routes in the ZyXEL Device. 16.1 Static Route Overview Each remote node specifies only the network to which the gateway is directly connected, and the ZyXEL Device has no knowledge of the networks beyond. For instance, the ZyXEL Device knows about network N2 in the following figure through remote node Router 1.

  • Page 194: Ip Static Route Edit Screen

    Chapter 16 Static Route The first static route is the default route and cannot be modified or deleted. Figure 112 Management > Static Route > IP Static Route Each field is described in the following table. Table 82 Management > Static Route > IP Static Route LABEL Name Active...

  • Page 195: Figure 113 Management > Static Route > Ip Static Route > Edit

    Figure 113 Management > Static Route > IP Static Route > Edit Each field is described in the following table. Table 83 Management > Static Route > IP Static Route > Edit LABEL DESCRIPTION Route Name Enter the name of the static route. Active Select this if you want the static route to be used.
  • Page 196 Chapter 16 Static Route P-2302HWUDL-P1 Series User’s Guide...

  • Page 197: Bandwidth Mgmt

    H A P T E R Use these screens to manage the amount of traffic the ZyXEL Device routes through each interface. 17.1 Bandwidth Management Overview Bandwidth management allows you to allocate an interface’s outgoing capacity to specific types of traffic. It can also help you make sure that the ZyXEL Device forwards certain types of traffic (especially real-time applications) with minimum delay.

  • Page 198: Proportional Bandwidth Allocation

    Chapter 17 Bandwidth MGMT 17.1.2 Proportional Bandwidth Allocation Bandwidth management allows you to define how much bandwidth each class gets; however, the actual bandwidth allotted to each class decreases or increases in proportion to actual available bandwidth. 17.1.3 Application-based Bandwidth Management You can create bandwidth classes based on individual applications (like VoIP, Web, FTP, E- mail and Video for example).

  • Page 199: Maximize Bandwidth Usage

    With the priority-based scheduler, the ZyXEL Device forwards traffic from bandwidth classes according to the priorities that you assign to the bandwidth classes. The larger a bandwidth class’s priority number is, the higher the priority. Assign real-time applications (like those using audio or video) a higher priority number to provide smoother operation.

  • Page 200: Table 86 Priority-Based Allotment Of Unused & Unbudgeted Bandwidth Example

    Chapter 17 Bandwidth MGMT The ZyXEL Device divides up the unbudgeted 2048 kbps among the classes that require more bandwidth. If the administration department only uses 1024 kbps of the budgeted 2048 kbps, the ZyXEL Device also divides the remaining 1024 kbps among the classes that require more bandwidth.

  • Page 201: Bandwidth Borrowing

    17.1.8 Bandwidth Borrowing Bandwidth borrowing allows a sub-class to borrow unused bandwidth from its parent class, whereas maximize bandwidth usage allows any bandwidth class to borrow any unused or unbudgeted bandwidth on the whole interface. Enable bandwidth borrowing on a sub-class to allow the sub-class to use the parent class’s unused bandwidth.

  • Page 202: Over Allotment Of Bandwidth

    Chapter 17 Bandwidth MGMT 17.1.9 Over Allotment of Bandwidth You can set the bandwidth management speed for an interface higher than the interface’s actual transmission speed. Higher priority traffic gets to use up to its allocated bandwidth, even if it takes up all of the interface’s available bandwidth. This could stop lower priority traffic from being sent.

  • Page 203: Figure 115 Management > Bandwidth Mgmt > Summary

    Figure 115 Management > Bandwidth MGMT > Summary Each field is described in the following table. Table 90 Management > Bandwidth MGMT > Summary LABEL DESCRIPTION Active Select this to enable bandwidth management on the LAN. Bandwidth management applies to all traffic flowing out of the router through the LAN, regardless of the traffic’s source.
  • Page 204 Chapter 17 Bandwidth MGMT Table 90 Management > Bandwidth MGMT > Summary LABEL Active Speed Scheduler Maximize Bandwidth Usage WLAN Active Speed Scheduler Maximize Bandwidth Usage Apply Reset DESCRIPTION Select this to enable bandwidth management on the WAN. Bandwidth management applies to all traffic flowing out of the router through the WAN, regardless of the traffic’s source.

  • Page 205: Bandwidth Class Setup Screen

    17.2.2 Bandwidth Class Setup Screen Use this screen to look at the configured bandwidth classes by individual interface. Each interface has a permanent root class. The bandwidth budget of the root class is equal to the speed you configured on the interface (see for all the bandwidth in the Root Class that is not allocated to bandwidth classes.

  • Page 206: Bandwidth Class Edit Screen

    Chapter 17 Bandwidth MGMT 17.2.3 Bandwidth Class Edit Screen Use this screen to configure a bandwidth management class. For each interface, you must enable bandwidth management before you can configure classes. To access this screen, click Add Sub-Class in Management > Bandwidth MGMT > Class Setup.

  • Page 207: Bandwidth Monitor Screen

    Table 92 Management > Bandwidth MGMT > Class Setup > Edit LABEL DESCRIPTION Borrow bandwidth Select this option to allow a sub-class to borrow bandwidth from its parent class if from parent class the parent class is not using up its bandwidth budget. Bandwidth borrowing is governed by the priority of the sub-classes.

  • Page 208: Figure 118 Management > Bandwidth Mgmt > Monitor

    Chapter 17 Bandwidth MGMT Figure 118 Management > Bandwidth MGMT > Monitor Each field is described in the following table. Table 93 Management > Bandwidth MGMT > Monitor LABEL Interface Class Name Budget (kbps) Current Usage (kbps) Refresh DESCRIPTION Select the interface at which you want to look in this screen. This field displays the name of each bandwidth class in the selected interface.

  • Page 209: Remote Mgmt

    H A P T E R Use these screens to control which computers can use which services to access the ZyXEL Device on each interface. 18.1 Remote Management Overview Remote management allows you to determine which services/protocols can access which ZyXEL Device interface (if any) from which computers.

  • Page 210: System Timeout

    Chapter 18 Remote MGMT • Use the ZyXEL Device’s LAN IP address when configuring from the LAN. 18.1.3 System Timeout There is a default system management idle timeout of five minutes (three hundred seconds). The ZyXEL Device automatically logs you out if the management session remains idle for longer than this timeout period.

  • Page 211: Ftp Screen

    Figure 120 Management > Remote MGMT > Telnet Each field is described in the following table. Table 96 Management > Remote MGMT > Telnet LABEL DESCRIPTION Server Port Enter the port number this service can use to access the ZyXEL Device. The computer must use the same port number.

  • Page 212: Snmp

    Chapter 18 Remote MGMT Table 97 Management > Remote MGMT > FTP LABEL Secured Client IP Address Apply Cancel 18.3 SNMP Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite.

  • Page 213: Supported Mibs

    The managed devices contain object variables/managed objects that define each piece of information to be collected about a device. Examples of variables include such as number of packets received, node port status etc. A Management Information Base (MIB) is a collection of managed objects.

  • Page 214: Dns Screen

    Chapter 18 Remote MGMT Figure 123 Management > Remote MGMT > SNMP The following table describes the labels in this screen. Table 99 Remote Management: SNMP LABEL SNMP Configuration Get Community Set Community Trap Community Trap Destination SNMP Service Port Service Access Secured Client IP Address...

  • Page 215: Security Screen

    Figure 124 Management > Remote MGMT > DNS Each field is described in the following table. Table 100 Management > Remote MGMT > DNS LABEL DESCRIPTION Server Port This field is read-only. This field displays the port number this service uses to access the ZyXEL Device.

  • Page 216: Table 101 Management > Remote Mgmt > Security

    Chapter 18 Remote MGMT Each field is described in the following table. Table 101 Management > Remote MGMT > Security LABEL Respond to Ping Do not respond to requests for unauthorized services Apply Cancel DESCRIPTION Select the interface(s) on which the ZyXEL Device should respond to incoming ping requests.

  • Page 217: Upnp

    H A P T E R Use this screen to set up UPnP. 19.1 Introducing Universal Plug and Play Universal Plug and Play (UPnP) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. A UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network.

  • Page 218: Upnp And Zyxel

    Chapter 19 UPnP All UPnP-enabled devices may communicate freely with each other without additional configuration. Disable UPnP if this is not your intention. 19.1.4 UPnP and ZyXEL ZyXEL has achieved UPnP certification from the Universal Plug and Play Forum UPnP™ Implementors Corp.

  • Page 219: Figure 127 Add/Remove Programs: Windows Setup: Communication: Components

    Figure 127 Add/Remove Programs: Windows Setup: Communication: Components 4 Click OK to go back to the Add/Remove Programs Properties window and click Next. 5 Restart the computer when prompted. 19.2.1.2 Installing UPnP in Windows XP Follow the steps below to install the UPnP in Windows XP. 1 Click Start and Control Panel.

  • Page 220: Figure 129 Windows Optional Networking Components Wizard

    Chapter 19 UPnP Figure 129 Windows Optional Networking Components Wizard 5 In the Networking Services window, select the Universal Plug and Play check box. Figure 130 Networking Services 6 Click OK to go back to the Windows Optional Networking Component Wizard window and click Next.

  • Page 221: Using Upnp In Windows Xp Example

    19.2.2 Using UPnP in Windows XP Example This section shows you how to use the UPnP feature in Windows XP. You must already have UPnP installed in Windows XP and UPnP activated on the ZyXEL Device. Make sure the computer is connected to a LAN port of the ZyXEL Device. Turn on your computer and the ZyXEL Device.

  • Page 222: Figure 132 Internet Connection Properties

    Chapter 19 UPnP Figure 132 Internet Connection Properties 4 You may edit or delete the port mappings or click Add to manually add port mappings. P-2302HWUDL-P1 Series User’s Guide...

  • Page 223: Figure 133 Internet Connection Properties: Advanced Settings

    Figure 133 Internet Connection Properties: Advanced Settings Figure 134 Internet Connection Properties: Advanced Settings: Add 5 When the UPnP-enabled device is disconnected from your computer, all port mappings will be deleted automatically. 6 Select Show icon in notification area when connected option and click OK. An icon displays in the system tray.

  • Page 224: Figure 135 System Tray Icon

    Chapter 19 UPnP Figure 135 System Tray Icon 7 Double-click on the icon to display your current Internet connection status. Figure 136 Internet Connection Status 19.2.2.2 Web Configurator Easy Access With UPnP, you can access the web-based configurator on the ZyXEL Device without finding out the IP address of the ZyXEL Device first.

  • Page 225: Figure 137 Network Connections

    Figure 137 Network Connections 4 An icon with the description for each UPnP-enabled device displays under Local Network. 5 Right-click on the icon for your ZyXEL Device and select Invoke. The web configurator login screen displays. P-2302HWUDL-P1 Series User’s Guide Chapter 19 UPnP...

  • Page 226: Figure 138 Network Connections: My Network Places

    Chapter 19 UPnP Figure 138 Network Connections: My Network Places 6 Right-click on the icon for your ZyXEL Device and select Properties. A properties window displays with basic information about the ZyXEL Device. Figure 139 Network Connections: My Network Places: Properties: Example P-2302HWUDL-P1 Series User’s Guide...

  • Page 227: Upnp Screen

    19.3 UPnP Screen Use this screen to set up UPnP in your ZyXEL Device. To access this screen, click Management > UPnP. Figure 140 Management > UPnP Each field is described in the following table. Table 102 Management > UPnP LABEL DESCRIPTION Device Name...
  • Page 228 Chapter 19 UPnP P-2302HWUDL-P1 Series User’s Guide...

  • Page 229: Sharing A Usb Printer

    H A P T E R Sharing a USB Printer This chapter describes how you can share a USB printer via your ZyXEL Device. 20.1 Overview The ZyXEL Device allows you to share a USB printer on your LAN. You can do this by connecting a USB printer to one of the USB ports on the ZyXEL Device and then configuring a TCP/IP port on the computers connected to your network.

  • Page 230: Configure A Tcp/Ip Printer Port

    Chapter 20 Sharing a USB Printer • Your operating system must support TCP/IP ports for printing and be compatible with the Line Printer Remote (LPR) protocol. • A USB printer with the driver already installed on your computer. 20.3 Configure a TCP/IP Printer Port This example shows screens from a Windows 2000 Professional operating system.

  • Page 231: Figure 143 Open Printer Properties

    Figure 143 Open Printer Properties 4 Select the Ports tab and click Add Port... Figure 144 Printer Properties Window 5 A Printer Ports window appears. Select Standard TCP/IP Port and click New Port... Figure 145 Add a Port Window P-2302HWUDL-P1 Series User’s Guide Chapter 20 Sharing a USB Printer...

  • Page 232: Figure 146 Add A Port Wizard

    Chapter 20 Sharing a USB Printer 6 Add Standard TCP/IP Printer Port Wizard window opens up. Click Next to start configuring the printer port. Figure 146 Add a Port Wizard 7 Enter the IP address of the ZyXEL Device to which the printer is connected in the Printer Name or IP Address: field.

  • Page 233: Figure 148 Custom Port Settings

    Figure 148 Custom Port Settings 9 Confirm the IP address of the ZyXEL Device in the IP Address field. 10 Select LPR under Protocol. 11 Type the LPR queue name of your printer model in the Queue Name field and click OK.

  • Page 234: Print Server Screen

    Chapter 20 Sharing a USB Printer Figure 150 Finish Adding the TCP/IP Port 13 Repeat steps 1 to 12 to add this printer to other computers on your network. 20.4 Print Server Screen The print server screen is used to confirm that the ZyXEL Device and the USB printer are able to communicate successfully.

  • Page 235: Adding A New Printer Example

    Table 103 Configuring Print Server LABEL Print Port Status Apply Cancel 20.5 Adding a New Printer Example 1 Open your Printers folder and double click Add Printer. Figure 152 Printers Folder 2 The Add Printer Wizard screen displays. Click Next. P-2302HWUDL-P1 Series User’s Guide DESCRIPTION This field displays the print server status on the ZyXEL Device.

  • Page 236: Figure 153 Add Printer Wizard: Welcome

    Chapter 20 Sharing a USB Printer Figure 153 Add Printer Wizard: Welcome 3 Select Local printer and click Next. Figure 154 Add Printer Wizard: Local or Network Printer 4 Select an LPT (Line Printing Terminal) port (a parallel port) as the computer interface for the USB printer.

  • Page 237: Figure 155 Add Printer Wizard: Select The Printer Port

    Figure 155 Add Printer Wizard: Select the Printer Port 5 Select the make of the printer that you want to connect to the print server in the Manufacturers list of printers. 6 Select the printer model from the list of Printers. 7 If your printer is not displayed in the list of Printers, you can insert the printer driver installation CD/disk or download the driver file to your computer, click Have Disk…...

  • Page 238: Figure 157 Add Printer Wizard: Use Existing Driver

    Chapter 20 Sharing a USB Printer Figure 157 Add Printer Wizard: Use Existing Driver 10 Type a name to identify the printer and then click Next to continue. Figure 158 Add Printer Wizard: Name Your Printer 11 The ZyXEL Device is a print server itself and you do not need to have your computer act as a print server by sharing the printer with other users in the same network;...

  • Page 239: Figure 159 Add Printer Wizard: Printer Sharing

    Figure 159 Add Printer Wizard: Printer Sharing 12 Select Yes and then click the Next button if you want to print a test page. A pop-up screen displays to ask if the test page printed correctly. Otherwise select No and then click Next to continue.

  • Page 240: Macintosh Os X Adding Printer Example

    Chapter 20 Sharing a USB Printer Figure 161 Add Printer Wizard Complete 20.6 Macintosh OS X Adding Printer Example Use the following steps to set up a print server driver on your Macintosh computer. 1 Click the Print Center icon of icons/shortcuts at the bottom of the desktop).

  • Page 241: Figure 164 Applications Folder

    Figure 164 Applications Folder 5 Double-click the Print Center icon. Figure 165 Utilities Folder 6 Click the Add icon at the top of the screen. Figure 166 Printer List Folder 7 Set up your printer in the Printer List configuration screen. Select IP Printing from the drop-down list box.

  • Page 242: Figure 167 Printer Configuration

    Chapter 20 Sharing a USB Printer Figure 167 Printer Configuration 12 Click Add to select a printer model, save and close the Printer List configuration screen. Figure 168 Printer Model 13 The Name LP1 on 192.168.1.1 displays in the Printer List field. The default printer Name displays in bold type.

  • Page 243: File Sharing

    H A P T E R Use these screens to set up file sharing through your ZyXEL Device. 21.1 File Sharing Implementation Overview Your ZyXEL Device allows you to connect USB 2.0 (or lower) file storage devices so that they can be accessed by users connected to your network. A file storage device can be a USB memory stick or a hard drive with a USB connector.

  • Page 244: Sharing Files Via The Zyxel Device

    Chapter 21 File Sharing partition), each device (or partition) is given its own folder. These folders are called “shares”. 3 Configure a user account. Anyone who wants to access your shared files must enter a user name and password. See 21.2 Sharing Files via the ZyXEL Device The ZyXEL Device uses Common Internet File System (CIFS) protocol for its file sharing functions.

  • Page 245: User Accounts

    Figure 171 Check the Workgroup Name 21.3 User Accounts The ZyXEL Device requires that a user enter a user name and password in order to access files on the USB storage device. When you browse to the ZyXEL Device you are prompted for a user name and password before you can access files on the USB storage device.

  • Page 246: Figure 173 Management > File Sharing

    Chapter 21 File Sharing Figure 173 Management > File Sharing Each field is described in the following table. Table 104 Management > File Sharing LABEL Enable File Sharing Services Workgroup Name System Code Page Active User Name Password Retype to Confirm Retype the password. DESCRIPTION Select this to enable file sharing through the ZyXEL Device.

  • Page 247: Accessing Files Via The Zyxel Device

    Table 104 Management > File Sharing LABEL DESCRIPTION Default Share These fields identify the default shares on the ZyXEL Device. Directory List This is a read-only index number of the default share on the ZyXEL Device. When more than one USB disk (or a USB hard drive with multiple shares) is connected to the ZyXEL Device this index number identifies the different disks.

  • Page 248: Using The Run Utility To Share Files

    Chapter 21 File Sharing Figure 174 File Sharing via Windows Explorer 21.5.2 Using the Run Utility to Share Files On your Windows 2000 computer, click Start, Run and type a double backslash “\\” followed by the IP address of the ZyXEL Device and click OK. Figure 175 Run Utility to Browse Files The Run utility automatically opens Windows Explorer and displays the contents of the USB storage device connected to your ZyXEL Device.

  • Page 249: Figure 176 Browse To A File Share Via Workgroup Name

    Chapter 21 File Sharing Once the ZyXEL Device is a member of your workgroup, use Windows Explorer to browse to the file “share” by locating the workgroup in your file system. It is located under My Network Places. In our example the workgroup name is the default “Workgroup”. Figure 176 Browse to a File Share via Workgroup Name P-2302HWUDL-P1 Series User’s Guide...
  • Page 250 Chapter 21 File Sharing P-2302HWUDL-P1 Series User’s Guide...

  • Page 251: Maintanence And Troubleshooting

    Maintanence and Troubleshooting System (253) Logs (261) Tools (273) Troubleshooting (279)

  • Page 253: System

    H A P T E R Use this screen to set up general system settings, change the system mode, change the password, configure the DDNS server settings, and set the current date and time. 22.1 System Overview 22.1.1 System Name System Name is for identification purposes.

  • Page 254: Dynamic Dns Overview

    Chapter 22 System Figure 177 Maintenance > System > General Each field is described in the following table. Table 105 Maintenance > System > General LABEL System Setup System Name Domain Name Administrator Inactivity Timer Password Setup Old Password New Password Retype to Confirm Type the new password again.

  • Page 255: Dns Server Address Assignment

    22.2.1 DNS Server Address Assignment Use DNS (Domain Name System) to map a domain name to its corresponding IP address and vice versa, for instance, the IP address of www.zyxel.com is 204.217.0.2. The DNS server is extremely important because without it, you must know the IP address of a computer before you can access it.

  • Page 256: Figure 178 Maintenance > System > Dynamic Dns

    Chapter 22 System Figure 178 Maintenance > System > Dynamic DNS Each field is described in the following table. Table 106 Maintenance > System > Dynamic DNS LABEL Dynamic DNS Setup Enable Dynamic Service Provider Dynamic DNS Type Host Name User Name Password Enable Wildcard...

  • Page 257: Time Setting Overview

    Table 106 Maintenance > System > Dynamic DNS LABEL DESCRIPTION Dynamic DNS Select this if you want the DDNS server to update the IP address of the host server auto detect name(s) automatically. Select this option when there are one or more NAT routers IP address between the ZyXEL Device and the DDNS server.

  • Page 258: Resetting The Time

    Chapter 22 System 22.3.2 Resetting the Time The ZyXEL Device resets the time in the following instances: • When the ZyXEL Device starts up. • When you click Apply in the • 24-hour intervals after starting. 22.3.3 Time Settings Screen To access this screen, click Maintenance >...
  • Page 259 Table 108 Maintenance > System > Time Setting LABEL DESCRIPTION Time Protocol Select the time service protocol that your time server uses.Check with your ISP or network administrator, or use trial-and-error to find a protocol that works. Daytime (RFC 867) - This format is day/month/year/time zone. Time (RFC 868) - This format displays a 4-byte integer giving the total number of seconds since 1970/1/1 at 0:0:0.
  • Page 260 Chapter 22 System P-2302HWUDL-P1 Series User’s Guide...

  • Page 261: Logs

    H A P T E R Use these screens to look at log entries and alerts and to configure the ZyXEL Device’s log and alert settings. 23.1 Logs Overview For a list of log messages, see 23.1.1 Alerts An alert is a type of log that warrants more serious attention. Some categories such as System Errors consist of both logs and alerts.

  • Page 262: Logs Screens

    Chapter 23 Logs 23.2 Logs Screens 23.2.1 View Log Screen Use this screen to look at log entries and alerts. Alerts are written in red. To access this screen, click Maintenance > Logs > View Log. Figure 180 Maintenance > Logs > View Log Click a column header to sort log entries in descending (later-to-earlier) order.

  • Page 263: Log Settings Screen

    23.2.2 Log Settings Screen Use this screen to configure where the ZyXEL Device sends logs and alerts, the schedule for sending logs, and which logs and alerts are sent or recorded. To access this screen, click Maintenance > Logs > Log Settings. Figure 181 Maintenance >...
  • Page 264 Chapter 23 Logs Table 111 Maintenance > Logs > Log Settings LABEL Mail Subject Send Log to Send Alerts to Log Schedule Day for Sending Time for Sending Clear log after sending mail Syslog Logging Active Syslog Server IP Address Log Facility Active Log and Alert...

  • Page 265: Log Message Descriptions

    23.3 Log Message Descriptions The following tables provide descriptions of example log messages. Table 112 System Error Logs LOG MESSAGE WAN connection is down. %s exceeds the max. number of session per host! Table 113 System Maintenance Logs LOG MESSAGE Time synchronization is successful Time synchronization failed...

  • Page 266: Table 114 Access Control Logs

    Chapter 23 Logs Table 113 System Maintenance Logs (continued) LOG MESSAGE Too large ICMP packet has been dropped Configuration Change: PC = 0x%x, Task ID = 0x%x Table 114 Access Control Logs LOG MESSAGE Firewall default policy: [ TCP | UDP | IGMP | ESP | GRE | OSPF ] <Packet Direction>...

  • Page 267: Table 116 Packet Filter Logs

    Table 115 TCP Reset Logs (continued) LOG MESSAGE Exceed MAX incomplete, sent TCP RST Access block, sent TCP Table 116 Packet Filter Logs LOG MESSAGE [ TCP | UDP | ICMP | IGMP | Generic ] packet filter matched (set: %d, rule: %d) or type and code details, see Table 117 ICMP Logs LOG MESSAGE...

  • Page 268: Table 119 Upnp Logs

    Chapter 23 Logs Table 118 PPP Logs (continued) LOG MESSAGE ppp:LCP Closing ppp:IPCP Closing Table 119 UPnP Logs LOG MESSAGE UPnP pass through Firewall Table 120 Content Filtering Logs LOG MESSAGE %s: Keyword blocking %s: Not in trusted web list %s: Forbidden Web site The web site is in the forbidden web site list.

  • Page 269: Table 122 Remote Management Logs

    Table 121 Attack Logs (continued) LOG MESSAGE ip spoofing - WAN [ TCP | UDP | IGMP | ESP | GRE | OSPF ] ip spoofing - WAN ICMP (type:%d, code:%d) icmp echo : ICMP (type:%d, code:%d) syn flood TCP ports scan TCP teardrop TCP teardrop UDP...

  • Page 270: Table 123 Icmp Notes

    Chapter 23 Logs Table 122 Remote Management Logs LOG MESSAGE Remote Management: HTTP or UPnP denied Remote Management: WWW denied Remote Management: HTTPS denied Remote Management: SSH denied Remote Management: ICMP Ping response denied Remote Management: DNS denied Table 123 ICMP Notes TYPE CODE DESCRIPTION...

  • Page 271: Table 124 Sip Logs

    Table 123 ICMP Notes (continued) TYPE CODE DESCRIPTION Timestamp Timestamp request message Timestamp Reply Timestamp reply message Information Request Information request message Information Reply Information reply message Table 124 SIP Logs LOG MESSAGE SIP Registration Success by SIP:SIP Phone Number SIP Registration Fail by SIP:SIP Phone Number SIP UnRegistration...
  • Page 272 Chapter 23 Logs P-2302HWUDL-P1 Series User’s Guide...

  • Page 273: Tools

    H A P T E R Use these screens to upload new firmware, back up and restore the configuration, and restart the ZyXEL Device. 24.1 Tools Overview 24.1.1 ZyXEL Firmware Find firmware at www.zyxel.com "*.bin" extension, e.g., "ZyXEL Device.bin". The upload process uses HTTP (Hypertext Transfer Protocol) and may take up to two minutes.

  • Page 274: Firmware Upload Screens

    Chapter 24 Tools Each field is described in the following table. Table 127 Maintenance > Tools > Firmware LABEL File Path Browse... Upload 24.2.2 Firmware Upload Screens Do not turn off the device while firmware upload is in progress! When the ZyXEL Device starts to upload firmware, the Firmware Upload in Process screen appears.

  • Page 275: Configuration Screen

    If the upload is not successful, the following screen appears. Figure 185 Firmware Upload Error Click Return to go back to the 24.2.3 Configuration Screen Use this screen to back up or restore the configuration of the ZyXEL Device. You can also use this screen to reset the ZyXEL Device to the factory default settings.

  • Page 276: Restore Configuration Screens

    Chapter 24 Tools Table 128 Maintenance > Tools > Configuration LABEL File Path Browse Upload Back to Factory Defaults Reset 24.2.4 Restore Configuration Screens Do not turn off the device while configuration file upload is in progress. When the ZyXEL Device has finished restoring the selected configuration file, the following screen appears.

  • Page 277: Restart Screen

    If the ZyXEL Device’s IP address is different in the configuration file you selected, you may need to change the IP address of your computer to be in the same subnet as that of the default management IP address (192.168.5.1). See your Quick Start Guide or the appendices for details on how to set up your computer’s IP address.
  • Page 278 Chapter 24 Tools P-2302HWUDL-P1 Series User’s Guide...

  • Page 279: Troubleshooting

    H A P T E R This chapter offers some suggestions to solve problems you might encounter. The potential problems are divided into the following categories. • Power, Hardware Connections, and LEDs • ZyXEL Device Access and Login • Internet Access •...

  • Page 280: Zyxel Device Access And Login

    Chapter 25 Troubleshooting 25.2 ZyXEL Device Access and Login I forgot the IP address for the ZyXEL Device. 1 The default IP address is 192.168.1.1. 2 If you changed the IP address and have forgotten it, you might get the IP address of the ZyXEL Device by looking up the IP address of the default gateway for your computer.

  • Page 281: Internet Access

    5 Reset the device to its factory defaults, and try to access the ZyXEL Device with the default IP address. See 6 If the problem continues, contact the network administrator or vendor, or try one of the advanced suggestions. Advanced Suggestions •...

  • Page 282: Phone Calls And Voip

    Chapter 25 Troubleshooting 4 If the problem continues, contact your ISP. The Internet connection is slow or intermittent. 1 There might be a lot of traffic on the network. Try closing some programs that use the Internet, especially peer-to-peer applications. 2 Check the signal strength.

  • Page 283: Outgoing Calls

    25.5.1 Outgoing Calls The following figure represents the default behavior of your ZyXEL Device when two SIP accounts are configured and you are using two phones. When you place a call from phone 1 or phone 2, the ZyXEL Device will use SIP account 1. Figure 192 Outgoing Calls: Default In the next example, phone port 1 is configured to use SIP account 1 and phone port 2 is configured to use SIP account 2.

  • Page 284: Figure 194 Incoming Calls: Default

    Chapter 25 Troubleshooting Figure 194 Incoming Calls: Default In the next example, phone port 1 is configured to use SIP account 1 and phone port 2 is configured to use SIP account 2 for incoming calls. In this case, every time you receive a call from your SIP account 1, the phone connected to phone port 1 rings.

  • Page 285: Part Vii: Appendices And Index

    Appendices and Index Product Specifications (287) IP Addresses and Subnetting (299) SIP Passthrough (321) Internal SPTGEN (323) Services (339) Legal Information (343) Customer Support (347) Index (351)

  • Page 287: Appendix A Product Specifications

    P P E N D I X Product Specifications See also the introduction chapter for a general overview of the key features. Specification Tables Table 129 Device Specifications Default IP Address Default Management Subnet Mask Default Password Dimensions Weight WAN Port Ethernet Ports Phone Ports Line Port (P-...

  • Page 288: Table 130 Firmware Features

    Appendix A Product Specifications Table 130 Firmware Features FEATURE Device Management Firmware Upgrade VoIP DECT GAP Base Station USB File/Print Server IEEE 802.11g Wireless Wireless Security MAC Address Filter Any IP Configuration Backup & Restoration Network Address Translation (NAT) Port Forwarding DHCP (Dynamic Host Configuration Protocol) Dynamic DNS Support...

  • Page 289: Table 131 Feature Specifications

    Table 130 Firmware Features FEATURE Time and Date Logging and Tracing PPPoE Universal Plug and Play (UPnP) Table 131 Feature Specifications Voice Functions DECT Base Station Wireless Protocol Support P-2302HWUDL-P1 Series User’s Guide DESCRIPTION Get the current time and date from an external server when you turn on your ZyXEL Device.

  • Page 290: Table 132 Zyxel Device Power Adaptor Specifications

    Appendix A Product Specifications Table 131 Feature Specifications (continued) Management Firewall Content Filtering NAT/SUA Static Routes Power Adaptor Specifications Table 132 ZyXEL Device Power Adaptor Specifications NORTH AMERICAN PLUG STANDARDS AC Power Adapter Model Input Power Output Power Power Consumption Safety Standards EUROPEAN PLUG STANDARDS AC Power Adapter Model...
  • Page 291 Table 132 ZyXEL Device Power Adaptor Specifications (continued) Power Consumption Safety Standards AUSTRALIA AND NEW ZEALAND PLUG STANDARDS AC Power Adapter Model Input Power Output Power Power Consumption Safety Standards P-2302HWUDL-P1 Series User’s Guide Appendix A Product Specifications 15 Watt Max. ITS-GS (BS EN 60950-1) AA-161AE AC 240Volts/50Hz/140mA...
  • Page 292 Appendix A Product Specifications P-2302HWUDL-P1 Series User’s Guide...

  • Page 293: Appendix B Pop-Up Windows, Java And Javascript Permissions

    P P E N D I X Pop-Up Windows, Java and JavaScript Permissions This appendix show you how to change your browser settings to ensure that the web configurator works properly 25.6 Pop-up Windows, JavaScripts and Java Permissions In order to use the web configurator you need to allow: •...

  • Page 294: Figure 196 Pop-Up Blocker

    Appendix B Pop-Up Windows, Java and JavaScript Permissions Figure 196 Pop-up Blocker You can also check if pop-up blocking is disabled in the Pop-up Blocker section in the Privacy tab. 1 In Internet Explorer, select Tools, Internet Options, Privacy. 2 Clear the Block pop-ups check box in the Pop-up Blocker section of the screen. This disables any web pop-up blockers you may have enabled.

  • Page 295: Figure 198 Internet Options

    Figure 198 Internet Options 3 Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.1.1. 4 Click Add to move the IP address to the list of Allowed sites. Figure 199 Pop-up Blocker Settings P-2302HWUDL-P1 Series User’s Guide Appendix B Pop-Up Windows, Java and JavaScript Permissions...

  • Page 296: Javascripts

    Appendix B Pop-Up Windows, Java and JavaScript Permissions 5 Click Close to return to the Privacy screen. 6 Click Apply to save this setting. 25.6.2 JavaScripts If pages of the web configurator do not display properly in Internet Explorer, check that JavaScripts are allowed.

  • Page 297: Java Permissions

    Figure 201 Security Settings - Java Scripting 25.6.3 Java Permissions 1 From Internet Explorer, click Tools, Internet Options and then the Security tab. 2 Click the Custom Level... button. 3 Scroll down to Microsoft VM. 4 Under Java permissions make sure that a safety level is selected. 5 Click OK to close the window.

  • Page 298: Figure 203 Java (Sun)

    Appendix B Pop-Up Windows, Java and JavaScript Permissions 25.6.3.1 JAVA (Sun) 1 From Internet Explorer, click Tools, Internet Options and then the Advanced tab. 2 make sure that Use Java 2 for <applet> under Java (Sun) is selected. 3 Click OK to close the window. Figure 203 Java (Sun) P-2302HWUDL-P1 Series User’s Guide...

  • Page 299: Appendix C Ip Addresses And Subnetting

    P P E N D I X IP Addresses and Subnetting This appendix introduces IP addresses and subnet masks. IP addresses identify individual devices on a network. Every networking device (including computers, servers, routers, printers, etc.) needs an IP address to communicate across the network.

  • Page 300: Figure 204 Network Number And Host Id

    Appendix C IP Addresses and Subnetting Figure 204 Network Number and Host ID How much of the IP address is the network number and how much is the host ID varies according to the subnet mask. Subnet Masks A subnet mask is used to determine which bits are part of the network number, and which bits are part of the host ID (using a logical AND operation).

  • Page 301: Table 134 Subnet Masks

    Subnet masks are expressed in dotted decimal notation just like IP addresses. The following examples show the binary and decimal notation for 8-bit, 16-bit, 24-bit and 29-bit subnet masks. Table 134 Subnet Masks BINARY OCTET 8-bit mask 11111111 16-bit mask 11111111 24-bit mask 11111111...

  • Page 302: Figure 205 Subnetting Example: Before Subnetting

    Appendix C IP Addresses and Subnetting Table 136 Alternative Subnet Mask Notation (continued) SUBNET MASK 255.255.255.192 255.255.255.224 255.255.255.240 255.255.255.248 255.255.255.252 Subnetting You can use subnetting to divide one network into multiple sub-networks. In the following example a network administrator creates two sub-networks to isolate a group of servers from the rest of the company network for security reasons.

  • Page 303: Figure 206 Subnetting Example: After Subnetting

    Figure 206 Subnetting Example: After Subnetting In a 25-bit subnet the host ID has 7 bits, so each sub-network has a maximum of 2 possible hosts (a host ID of all zeroes is the subnet’s address itself, all ones is the subnet’s broadcast address).

  • Page 304: Table 138 Subnet 2

    Appendix C IP Addresses and Subnetting Table 138 Subnet 2 IP/SUBNET MASK IP Address IP Address (Binary) Subnet Mask (Binary) Subnet Address: 192.168.1.64 Broadcast Address: 192.168.1.127 Table 139 Subnet 3 IP/SUBNET MASK IP Address IP Address (Binary) Subnet Mask (Binary) Subnet Address: 192.168.1.128 Broadcast Address:...

  • Page 305: Table 142 24-Bit Network Number Subnet Planning

    Table 141 Eight Subnets (continued) SUBNET SUBNET ADDRESS Subnet Planning The following table is a summary for subnet planning on a network with a 24-bit network number. Table 142 24-bit Network Number Subnet Planning NO. “BORROWED” HOST BITS The following table is a summary for subnet planning on a network with a 16-bit network number.

  • Page 306: Private Ip Addresses

    Appendix C IP Addresses and Subnetting Table 143 16-bit Network Number Subnet Planning (continued) NO. “BORROWED” HOST BITS Configuring IP Addresses Where you obtain your network number depends on your particular situation. If the ISP or your network administrator assigns you a block of registered IP addresses, follow their instructions in selecting the IP addresses and the subnet mask.

  • Page 307: Appendix D Setting Up Your Computer's Ip Address

    P P E N D I X Setting up Your Computer’s IP All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Windows 95/98/Me/NT/2000/XP, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/ IP on your computer.

  • Page 308: Figure 207 Windows 95/98/Me: Network: Configuration

    Appendix D Setting up Your Computer’s IP Address Figure 207 WIndows 95/98/Me: Network: Configuration Installing Components The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks. If you need the adapter: 1 In the Network window, click Add.

  • Page 309: Figure 208 Windows 95/98/Me: Tcp/Ip Properties: Ip Address

    Configuring 1 In the Network window Configuration tab, select your network adapter's TCP/IP entry and click Properties 2 Click the IP Address tab. • If your IP address is dynamic, select Obtain an IP address automatically. • If you have a static IP address, select Specify an IP address and type your information into the IP Address and Subnet Mask fields.

  • Page 310: Figure 209 Windows 95/98/Me: Tcp/Ip Properties: Dns Configuration

    Appendix D Setting up Your Computer’s IP Address Figure 209 Windows 95/98/Me: TCP/IP Properties: DNS Configuration 4 Click the Gateway tab. • If you do not know your gateway’s IP address, remove previously installed gateways. • If you have a gateway IP address, type it in the New gateway field and click Add. 5 Click OK to save and close the TCP/IP Properties window.

  • Page 311: Figure 210 Windows Xp: Start Menu

    Figure 210 Windows XP: Start Menu 2 In the Control Panel, double-click Network Connections (Network and Dial-up Connections in Windows 2000/NT). Figure 211 Windows XP: Control Panel 3 Right-click Local Area Connection and then click Properties. P-2302HWUDL-P1 Series User’s Guide Appendix D Setting up Your Computer’s IP Address...

  • Page 312: Figure 212 Windows Xp: Control Panel: Network Connections: Properties

    Appendix D Setting up Your Computer’s IP Address Figure 212 Windows XP: Control Panel: Network Connections: Properties 4 Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and then click Properties. Figure 213 Windows XP: Local Area Connection Properties 5 The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP).

  • Page 313: Figure 214 Windows Xp: Internet Protocol (Tcp/Ip) Properties

    Figure 214 Windows XP: Internet Protocol (TCP/IP) Properties 6 If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK. Do one or more of the following if you want to configure additional IP addresses: •...

  • Page 314: Figure 215 Windows Xp: Advanced Tcp/Ip Properties

    Appendix D Setting up Your Computer’s IP Address Figure 215 Windows XP: Advanced TCP/IP Properties 7 In the Internet Protocol TCP/IP Properties window (the General tab in Windows XP): • Click Obtain DNS server address automatically if you do not know your DNS server IP address(es).

  • Page 315: Figure 216 Windows Xp: Internet Protocol (Tcp/Ip) Properties

    Figure 216 Windows XP: Internet Protocol (TCP/IP) Properties 8 Click OK to close the Internet Protocol (TCP/IP) Properties window. 9 Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window. 10 Close the Network Connections window (Network and Dial-up Connections in Windows 2000/NT).

  • Page 316: Figure 218 Macintosh Os X: Network

    Appendix D Setting up Your Computer’s IP Address 2 Click Network in the icon bar. • Select Automatic from the Location list. • Select Built-in Ethernet from the Show list. • Click the TCP/IP tab. 3 For dynamically assigned settings, select Using DHCP from the Configure list. Figure 218 Macintosh OS X: Network 4 For statically assigned settings, do the following: •...

  • Page 317: Figure 219 Red Hat 9.0: Kde: Network Configuration: Devices

    Linux This section shows you how to configure your computer’s TCP/IP settings in Red Hat Linux 9.0. Procedure, screens and file location may vary depending on your Linux distribution and release version. Make sure you are logged in as the root administrator. Using the K Desktop Environment (KDE) Follow the steps below to configure your computer IP address using the KDE.

  • Page 318: Figure 220 Red Hat 9.0: Kde: Ethernet Device: General

    Appendix D Setting up Your Computer’s IP Address Figure 220 Red Hat 9.0: KDE: Ethernet Device: General • If you have a dynamic IP address, click Automatically obtain IP address settings with and select dhcp from the drop down list. •...

  • Page 319: Figure 222 Red Hat 9.0: Kde: Network Configuration: Activate

    Figure 222 Red Hat 9.0: KDE: Network Configuration: Activate 7 After the network card restart process is complete, make sure the Status is Active in the Network Configuration screen. Using Configuration Files Follow the steps below to edit the network configuration files and set your computer IP address.

  • Page 320: Figure 225 Red Hat 9.0: Dns Settings In Resolv.conf

    Appendix D Setting up Your Computer’s IP Address Figure 225 Red Hat 9.0: DNS Settings in resolv.conf nameserver 172.23.5.1 nameserver 172.23.5.2 3 After you edit and save the configuration files, you must restart the network card. Enter ./network restart figure shows an example. Figure 226 Red Hat 9.0: Restart Ethernet Card [root@localhost init.d]# network restart Shutting down interface eth0:...

  • Page 321: Appendix E Sip Passthrough

    P P E N D I X Enabling/Disabling the SIP ALG You can turn off the ZyXEL Device SIP ALG to avoid retranslating the IP address of an existing SIP device that is using STUN. If you want to use STUN with a SIP client device (a SIP phone or IP phone for example) behind the ZyXEL Device, use the ip alg disable ALG_SIP command to turn off the SIP ALG.
  • Page 322 Appendix E SIP Passthrough P-2302HWUDL-P1 Series User’s Guide...

  • Page 323: Appendix F Internal Sptgen

    P P E N D I X This appendix introduces Internal SPTGEN. All menus shown in this appendix are example menus meant to show SPTGEN usage. Actual menus for your product may differ. Internal SPTGEN Overview Internal SPTGEN (System Parameter Table Generator) is a configuration text file useful for efficient configuration of multiple ZyXEL Devices.

  • Page 324: Figure 229 Invalid Parameter Entered: Command Line Example

    Appendix F Internal SPTGEN DO NOT alter or delete any field except parameters in the Input column. This appendix introduces Internal SPTGEN. All menus shown in this appendix are example menus meant to show SPTGEN usage. Actual menus for your product may differ. Internal SPTGEN File Modification - Important Points to Remember Each parameter you enter must be preceded by one “=”sign and one space.

  • Page 325: Figure 231 Internal Sptgen Ftp Download Example

    Figure 231 Internal SPTGEN FTP Download Example c:\ftp 192.168.1.1 220 PPP FTP version 1.0 ready at Sat Jan 1 03:22:12 2000 User (192.168.1.1:(none)): 331 Enter PASS command Password: 230 Logged in ftp>bin 200 Type I OK ftp> get rom-t ftp>bye c:\edit rom-t (edit the rom-t text file by a text editor and save it) You can rename your “...

  • Page 326: Table 144 Abbreviations Used In The Example Internal Sptgen Screens Table

    Appendix F Internal SPTGEN Example Internal SPTGEN Menus This section provides example Internal SPTGEN menus. Table 144 Abbreviations Used in the Example Internal SPTGEN Screens Table ABBREVIATION MEANING Field Identification Number Field Name Parameter Values Allowed INPUT An example of what you may enter Applies to the ZyXEL Device.
  • Page 327 Table 146 Menu 3 / Menu 3.2 TCP/IP and DHCP Ethernet Setup 30200001 = DHCP 30200002 = Client IP Pool Starting Address 30200003 = Size of Client IP Pool 30200004 = Primary DNS Server 30200005 = Secondary DNS Server 30200006 = Remote DHCP Server 30200008 = IP Address...
  • Page 328 Appendix F Internal SPTGEN Table 146 Menu 3 30201008 = IP Alias #1 Incoming protocol filters Set 3 30201009 = IP Alias #1 Incoming protocol filters Set 4 30201010 = IP Alias #1 Outgoing protocol filters Set 1 30201011 = IP Alias #1 Outgoing protocol filters Set 2 30201012 =...

  • Page 329: Table 147 Menu 4 Internet Access Setup

    Table 146 Menu 3 30500004 = RTS Threshold 30500005 = FRAG. Threshold 30500006 = 30500007 = Default Key 30500008 = WEP Key1 30500009 = WEP Key2 30500010 = WEP Key3 30500011 = WEP Key4 30500012 = Wlan Active 30500013 = Wlan 4X Mode */ MENU 3.5.1 WLAN MAC ADDRESS FILTER 30501001 =...
  • Page 330 Appendix F Internal SPTGEN Table 147 Menu 4 Internet Access Setup (continued) 40000003 = ISP's Name 40000004 = Encapsulation 40000005 = Multiplexing 40000006 = VPI # 40000007 = VCI # 40000008 = Service Name 40000009 = My Login 40000010 = My Password 40000011 = Single User Account...

  • Page 331: Table 148 Menu 12

    Table 147 Menu 4 Internet Access Setup (continued) 40000032= RIP Version 40000033= Nailed-up Connection Table 148 Menu 12 / Menu 12.1.1 IP Static Route Setup 120101001 = IP Static Route set #1, Name 120101002 = IP Static Route set #1, Active 120101003 = IP Static Route set #1, Destination IP address...
  • Page 332 Appendix F Internal SPTGEN Table 149 Menu 15 SUA Server Setup (continued) 150000007 = SUA Server #3 Active 150000008 = SUA Server #3 Protocol 150000009 = SUA Server #3 Port Start 150000010 = SUA Server #3 Port End 150000011 = SUA Server #3 Local IP address 150000012 = SUA Server #4 Active...

  • Page 333: Table 150 Menu 21.1 Filter Set #1

    Table 149 Menu 15 SUA Server Setup (continued) 150000041 = SUA Server #9 Local IP address 150000042 = SUA Server #10 Active 150000043 = SUA Server #10 Protocol 150000044 = SUA Server #10 Port Start 150000045 = SUA Server #10 Port End 150000046 = SUA Server #10 Local IP address 150000047 =...

  • Page 334: Table 151 Menu 21.1 Filer Set #2

    Appendix F Internal SPTGEN Table 150 Menu 21.1 Filter Set #1 (continued) 210101011 = IP Filter Set 1,Rule 1 Src Port Comp 210101013 = IP Filter Set 1,Rule 1 Act Match 210101014 = IP Filter Set 1,Rule 1 Act Not Match / Menu 21.1.1.2 set #1, rule #2 210102001 = IP Filter Set 1,Rule 2 Type...
  • Page 335 Table 151 Menu 21.1 Filer Set #2 (continued) 210201001 = IP Filter Set 2, Rule 1 Type 210201002 = IP Filter Set 2, Rule 1 Active 210201003 = IP Filter Set 2, Rule 1 Protocol 210201004 = IP Filter Set 2, Rule 1 Dest IP address 210201005 = IP Filter Set 2, Rule 1 Dest...

  • Page 336: Table 152 Menu 23 System Menus

    Appendix F Internal SPTGEN Table 151 Menu 21.1 Filer Set #2 (continued) 210202010 = IP Filter Set 2,Rule 2 Src Port 210202011 = IP Filter Set 2, Rule 2 Src Port Comp 210202013 = IP Filter Set 2, Rule 2 Act Match 210202014 = IP Filter Set 2, Rule 2 Act Not Match...

  • Page 337: Table 153 Menu 24.11 Remote Management Control

    Table 152 Menu 23 System Menus (continued) 230400004 = Authentication Databases 230400005 = Key Management Protocol 230400006 = Dynamic WEP Key Exchange 230400007 = 230400008 = WPA Mixed Mode 230400009 = Data Privacy for Broadcast/ Multicast packets 230400010 = WPA Broadcast/Multicast Key Update Timer Table 153 Menu 24.11 Remote Management Control / Menu 24.11 Remote Management Control...

  • Page 338: Table 154 Command Examples

    Appendix F Internal SPTGEN Command Examples The following are example Internal SPTGEN screens associated with the ZyXEL Device’s command interpreter commands. Table 154 Command Examples /ci command (for annex a): wan adsl opencmd 990000001 = ADSL OPMD /ci command (for annex B): wan adsl opencmd 990000001 = ADSL OPMD INPUT...

  • Page 339: Appendix G Services

    P P E N D I X The following table lists some commonly-used services and their associated protocols and port numbers. • Name: This is a short, descriptive name for the service. You can use this one or create a different one, if you like.
  • Page 340 Appendix G Services Table 155 Examples of Services (continued) NAME H.323 HTTP HTTPS ICMP IGMP (MULTICAST) User-Defined IMAP4 IMAP4S MSN Messenger NetBIOS NEW-ICQ NEWS NNTP PING POP3 POP3S PPTP PROTOCOL PORT(S) DESCRIPTION 1720 NetMeeting uses this protocol. Hyper Text Transfer Protocol - a client/ server protocol for the world wide web.
  • Page 341 Table 155 Examples of Services (continued) NAME PROTOCOL PPTP_TUNNEL User-Defined (GRE) RCMD REAL_AUDIO REXEC RLOGIN ROADRUNNER TCP/UDP RTELNET RTSP TCP/UDP SFTP SMTP SMTPS SNMP TCP/UDP SNMP-TRAPS TCP/UDP SQL-NET SSDP TCP/UDP STRM WORKS SYSLOG TACACS TELNET P-2302HWUDL-P1 Series User’s Guide Appendix G Services PORT(S) DESCRIPTION PPTP (Point-to-Point Tunneling Protocol)
  • Page 342 Appendix G Services Table 155 Examples of Services (continued) NAME TFTP VDOLIVE PROTOCOL PORT(S) DESCRIPTION Trivial File Transfer Protocol is an Internet file transfer protocol similar to FTP, but uses the UDP (User Datagram Protocol) rather than TCP (Transmission Control Protocol).

  • Page 343: Appendix H Legal Information

    ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved.
  • Page 344 Appendix H Legal Information If this device does cause harmful interference to radio/television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1 Reorient or relocate the receiving antenna.

  • Page 345: Zyxel Limited Warranty

    3 Select the certification you wish to view from this page. ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever...
  • Page 346 Appendix H Legal Information P-2302HWUDL-P1 Series User’s Guide...

  • Page 347: Appendix I Customer Support

    José, Costa Rica Czech Republic • E-mail: info@cz.zyxel.com • Telephone: +420-241-091-350 • Fax: +420-241-091-359 • Web Site: www.zyxel.cz • Regular Mail: ZyXEL Communications, Czech s.r.o., Modranská 621, 143 01 Praha 4 - Modrany, Ceská Republika P-2302HWUDL-P1 Series User’s Guide Customer Support...
  • Page 348 • Support E-mail: support@zyxel.fi • Sales E-mail: sales@zyxel.fi • Telephone: +358-9-4780-8411 • Fax: +358-9-4780 8448 • Web Site: www.zyxel.fi • Regular Mail: ZyXEL Communications Oy, Malminkaari 10, 00700 Helsinki, Finland France • E-mail: info@zyxel.fr • Telephone: +33-4-72-52-97-97 • Fax: +33-4-72-52-19-20 •...
  • Page 349 • Sales E-mail: sales@zyxel.com • Telephone: +1-800-255-4101, +1-714-632-0882 • Fax: +1-714-632-0858 • Web Site: www.us.zyxel.com • FTP Site: ftp.us.zyxel.com • Regular Mail: ZyXEL Communications Inc., 1130 N. Miller St., Anaheim, CA 92806- 2001, U.S.A. Norway • Support E-mail: support@zyxel.no • Sales E-mail: sales@zyxel.no •...
  • Page 350 Appendix I Customer Support • Web Site: www.zyxel.es • Regular Mail: ZyXEL Communications, Arte, 21 5ª planta, 28033 Madrid, Spain Sweden • Support E-mail: support@zyxel.se • Sales E-mail: sales@zyxel.se • Telephone: +46-31-744-7700 • Fax: +46-31-744-7701 • Web Site: www.zyxel.se • Regular Mail: ZyXEL Communications A/S, Sjöporten 4, 41764 Göteborg, Sweden Ukraine •...

  • Page 351: Index

    AbS (Analysis-by-Synthesis) Access Point, see AP adding a printer example adding a printer example, Macintosh OS Address Resolution Protocol (ARP) alert settings and SIP ALG (Application Layer Gateway alternative subnet mask notation analog phone Analysis-by-Synthesis (AbS) Any IP note Any IP example Any IP feature and NAT setup...
  • Page 352 Index command interface Common Internet File System (CIFS) computer’s IP address configuration successful upload web configurator contact information content filtering 187, 188, 189 scheduling copyright CoS (Class of Service) cost of transmission and WAN custom tones 132, 139 customer support data screening DECT and flashing...
  • Page 353 factory defaults fairness-based bandwidth management FAT (File Allocation Table) fax passthrough FCC interference statement File Allocation Table, see FAT file sharing 35, 243, 244 and workgroup 244, 248 overview user account web configurator Windows Explorer filtering Internet content, see also content filtering firewall and NAT 120, 180, 183...
  • Page 354 Index Internet Gateway Device (IGD) Internet Group Multicast protocol, see IGMP Internet Service Provider (ISP) Internet Telephony Service Provider (ITSP) IP address and ISP 52, 105 and LAN 105, 110 and WAN private range recommendation IP alias IP network and PSTN connection IP-PBX and IP address and WAN...
  • Page 355 multimedia and SIP MWI (Message Waiting Indication) nailed-up connection 131, 306 and Any IP and firewall 120, 180, 183 and LAN 105, 108 and remote management and UPnP and VoIP 130, 138 overview port forwarding server sets trigger ports web configurator NAT (Network Address Translation) NAT traversal navigating the web configurator...
  • Page 356 Index 133, 289 and VoIP 127, 133, 134, 139 QoS (Quality of Service) Quality of Service, see QoS RADIUS 81, 86 and WLAN 80, 86 Real Time Transport (RTP) recommendations for security recording custom tones redirect server, and SIP register server, and SIP registration product related documentation...
  • Page 357 SNMP (Simple Network Management Protocol) sound quality, and VoIP specification tables speed dial spoofing the MAC address 55, 96 SSID hiding SSID (Service Set IDentity) SSID and security stateful inspection static route default gateway metric overview static WEP 81, 85 status bar status indicators storage humidity...
  • Page 358 Index and VoIP 134, 139 VLAN (Virtual Local Area Network) VLAN group VLAN ID VLAN ID tags Voice Activity Detection, see VAD voice coding voice functions voice mail Voice over IP, see VoIP VoIP advanced settings and codecs and DECT and echo cancellation and frequencies and NAT...
  • Page 359 and WEP 81, 84 and WPA 81, 87 and WPA-PSK 81, 85 channels clients 89, 90 enabling encryption general settings modes overview recommendation security selecting security SSID terms explained web configurator WLAN security and encryption and IEEE 802.1x and SSID MAC address filter 80, 91 OTIST...

This manual is also suitable for:

P-2302hwl dect usbP-2302hwudl-p1 series

Table of Contents