Related Manuals for NARGESA MX700
Summary of Contents for NARGESA MX700
- Page 1 IRONWORKER MACHINE MX700 INSTRUCTIONS BOOK PRADA NARGESA, S.L Ctra. de Garrigàs a Sant Miquel s/n · 17476 Palau de Santa Eulàlia (Girona) SPAIN Tel. +34 972568085 · nargesa@nargesa.com · www.nargesa.com...
- Page 2 Thank you for choosing our machines www.nargesa.com...
-
Page 3: Table Of Contents
4.3. Admissible outer conditions ..................4.4. Connection to power supply ..................5. OPERATION MANUAL ......................5.1. Introduction ......................... 5.2. Feeding up of MX700 ....................5.3. Activation of the machine .................... 5.4. Working at manual mode .................... 5.5. Working at automatic mode .................. -
Page 4: Features Of The Machine
1.2. Description of the machine The MX700, has been especially designed for punching metal parts with different shapes depending on the type of punch. It may have other utilities by incorporating various accessories. It may be used for other purposes but always following the manufacturer's guidelines, which provide all dockable accessories to the machine. -
Page 5: Identification Of The Machne
Operational keypad Extractor Support base for diez Emergency stop Pedal Clamping point General switch Bench for dies Ventilation grill Box door Electric engine Electro-distributor Safety valve Hydraulic circuit container Emptying cap Oil filling cap INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700... -
Page 6: General Characteristics
- Dimensions: 1150x1390x2080 mm 1.5. Description of safety devices Protection devices of the MX700 are the extractor at the front of the machine to hold the material and avoid putting your hands between the punch and the workpiece. It also has a screen to prevent fragments projections, this display has a security system to prevent the punch from descending if the screen is raised, only if the key to cancel safety is turned, then it coul be possible to work with with the hazard light. -
Page 7: Transport And Storage
* Temperature -25 to 55 ° C or 75 ° C for periods not exceeding 24 hours (remember that these temperatures are in storage) * It is advisable not to stack heavy objects or machines. * Do not disassemble for storage. INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700... -
Page 8: Maintenance
- If the use is daily and continuous, grease them every day. - If the use is sporadic during the day then oil each week. - If the use is sporadic, grease once a month. Picture 6 1- Stop the machine INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700... -
Page 9: Installment And Starting Up
Picture 8 4.3. Admissible outer conditions - Temperature betwee +5ºC and +40ºC without exceeding an average temperature of +35ºC during 24h - Humidity between 30% and 90% with no water condensation. INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700... -
Page 10: Connection To Power Supply
IMPORTANT: This machine must be connected to a single outlet with earthing The MX700 is equipped with a three phased engine 230V / 400V with 5,5Kw connected on a star shape to connect into a power supply of 400V. It should be connected to an only power supply with the indicated requirements. -
Page 11: Operation Manual
Key for changing on to automatic mode Key for turning on to manual mode Key for deleting the counter of punching operations Wing for setting the OFF key to stop the lower and upper limits machine stop the punchn. INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700... -
Page 12: Introduction
5.1. Introduction This manual is intended to be useful to the user of the MX700, as it contains important information about the use and features of the machine. It is for this reason that it is recommended to follow step by step the points in this manual in order to understand the correct operation of the machine. -
Page 13: Working At Manual Mode
Press the pedal to punch. By proceeding as described here, see how the counter on the machine shown in the LCD display will be incremented by one. AUTOMATIC CNT: 2 Picture 15. Information of the Automatic Punching INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700... -
Page 14: Meter Deletion
5.6. Meter deletion The MX700 has a counter as you know, if you have carefully read the foregoing sections. This can be very favorable in case you need to count the punching operations, this requires a certain part, or the ones a third user has made with your machine a third part with your machine. -
Page 15: Desactivation Of The Machine
Activating the Emergency Stop button EMERGENCY STOP Picture 19. Information about Emergency Stop Error situations: Error on the Upper Displacement of the machine. ERROR ON UPPER DISPLACEMENT Picture 20. Information about Error on the upper Displacement INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700... - Page 16 Picture 21. Information of Error on Lower displacement Thus, the result of the situations mentioned above, the MX700 goes into such a state that aborts any operation being performed at that time, indicating on screen the anomalous situation that has occurred message.
-
Page 17: Warnings
6. WARNINGS The MX700 is equipped with a safety screen to prevent projected elements from causing any damage to the machine operator. This screen can only be raised for the preparation of tools, dies or punches, the machine can operate whenever the key is in "ON" position, this key is always to be controlled by the person responsible for the section or area in which the machine is located. - Page 18 - do not punch the part if it doesn’t stand on both sides of the extractor. When going backwards When going backward, the punchwill break down the correct extraction is When going backwards When going backward, the punchwill break down the correct extraction is INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
-
Page 19: Accessories
(round, square, rectangular, oblong). There are also other accessories or dies coupled to the piston to cut, bend pipe, blunt, folding, etc. The MX700, has got a wide range of punches and dies which allows to make all kinds of jobs such as folding, punching, cutting, etc. - Page 20 40 mm 64 mm 43,5 mm 25x43mm 50 mm 58 mm 54 mm 25x70mm 75 mm 58 mm 79 mm N100 25x96mm 100 mm 58 mm 104 mm For different sizes, please ask the manufacturer. INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 21 4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19/20mm 46 mm 28,5 mm 21/22/24/26/28mm 60 mm 32 mm 31/33/35mm 78 mm 28,5 mm N100 40/44/48/53mm 100 mm 28,5 mm N125 58/64/70mm 125 mm 28,5 mm For different sizes, please ask the manufacturers. INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 22 Tube from 28,5 to 40mm TAP 40 CAB 60 MAN50 Tube from 40,5 to 50mm TAP 50 CAB 78 MAN60 Tube from 50,5 to 60mm TAP 60 CAB 85 For different sizes, please ask the manufacturers. INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 23 R (radius), W (flat bar width), T (flkat bar thickness) · In models B and C specify hole diameter · The ear shaped legth is always adjustable · Production capacity: 450 to 600 parts per hour. INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 24 Stripping Tooling 90º Adjustable 150x150 MX700 · REF. 140-02-02-00001 Stripping tooling for metal sheet, angle, etc...Adjustable up to 150x150mm to 90º fixed. Units per machine Max. Cutting capacity Weight 150x150x8 38 Kg Folding Tooling 100mm. MX700 · REF. 140-02-02-00033 Tooling for folding metal sheet and flat bar up to 100mm.
- Page 25 Max. Cutting capacity Miter cut Weight 80x80mm 50x50mm 32 Kg Flat bar Cutting Tooling 100 x 12. MX700 · REF. 140-02-02-00037 Tooling for cutting metal sheet or flat bar from 0.8mm up to 12mm thickness. Units per machine Max. Cutting capacity...
- Page 26 Units per machine Max. Pipe Diameter Min. Pipoe Diameter Weight 30x2mm 10x2mm 20 Kg Arrow tooling for Metal Sheet MX700 · REF. 140-02-02-00041 Tooling for punching metal sheet in arrow shapes for fences. Units per machine Sheet Max. Thickness Weight 22 Kg...
- Page 27 Angle and U Profile Punching Machine MX700 · REF. 140-02-01-00031 Base holder for punching angles. The punches and dies of different diameters are exchangeable. Units per machine Max. Hole Diameter Min. Hole Diameter Weight 28mm 7 Kg Flattening Tooling MX700 · REF. 140-02-02-00042 It’s an extractor which acts as the flat bar holder at the...
-
Page 28: Technical Annex
Technical annex Hydraulic punching machine MX700 List of parts Electric maps Hydraulic map... - Page 29 A1. List of parts INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 30 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 31 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 32 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 33 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 34 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 35 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 36 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 37 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 38 A2. Electric maps INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 39 INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 40 A3. Hydraulic map INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700...
- Page 41 3. Complete the form with your details and press Message Sent: confirms your data has been successfully sent to Prada Nargesa SL. Your machine has been registered and has a warranty of three years in total. Your request has been sent correctly. We will contact you right...