Table of Contents
Advertisement
EN
2.2.7 Options
Function designed for loads with hard to dry item s such as saucepans,
non-stick pans and plastic containers. Increases the hot rinse tempera-
ture and can be used in programmes featuring a final drying phase (see
programmes table).
PROGRAM DELAY
EN
(available for all programs except soak)
The "Program delay" function delays the beginning of the washing pro-
gram up to 24 hours from the moment in which programming takes place.
2
2 .
8 .
This makes it possible to use the dishwasher at a certain time of day.
Before programming a delay, open the door of the dishwasher, select the
A
t t
e h
n e
required washing program (see para 2.2 "Setting the washing program
cator lights of the fourth and fi fth program (ref. pr. 4, pr. 5 fi g. 2-04) fl ash.
and switching on and off"). Select the day by pressing the Program delay
Turn off the appliance by opening the door and pressing the on/off button (ref.
button (ref. 11 fig. 2-02); each time you press the button, the display in-
1 fi g. 2-02).
creases the delay before the appliance starts by 1 hour.
SPREAD HALF LOAD
Suitable when there are not many dishes to be washed, it saves energy
and reduces the program duration. Place dishes in both baskets then load
the detergent dispenser than less than the normal amount for a full load.
symbols programs according to the models
4
2.2.9
˜˜ ˜
12
USER INSTRUCTIONS
USER INSTRUCTIONS
S
i w
c t
h
n i
g
o
f f
d
o
t f
e h
p
o r
g
a r
m
t ,
ENERSAVE OPTION
This option further reduces energy consumption by opening the
door at the end of the cycle for more effective drying. At the end
of the wash an automatic device releases the door, which slowly
If it is necessary to open the door during the washing cycle, the
opens by a few centimetres. This allows optimal drying even with
program will be interrupted, the relative indicator light will continue to
low rinsing temperatures, for significant energy saving.
fl ash and a beep will indicate that the cycle has not terminated. Wait
The dishwasher remains in an idle state between the rinse stage
for about 1 minute before closing the door and continuing with the
and the end of the cycle to allow proper drying (the display
program. When the door closes, the program will start from where it
shows the time left until the end of the cycle). Opening the door
was interrupted. This operation should be performed only if neces-
at this stage causes the cycle to stop and ends the program.
sary as it could cause irregular program performance.
The program end is signalled by a short beep and the flashing
of the indicator lights for programs 4 and 5.
Enersave is activated automatically if the selected program is
R
E
M
O
V
N I
G
compatible with the option. It can be deactivated before the pro-
gram is started.
When the function is activated, opening of the door must not
A
t t
e h
n e
d
o
t f
e h
w
be impeded in any way; do not leave anything in the necessary
removing the dishes in order to allow them to cool. To prevent any
space in front of the door to allow it to open. Do not force the
water droplets on the upper rack from falling onto the dishes in the
door lock before the end of the cycle is signalled, as this would
lower rack, empty the lower rack fi rst and then the upper one.
damage the mechanism.
e h
i d
h s
w
a
h s
r e
e
m
T
H
E
D
S I
H
E
S
s a
i h
g n
p
o r
g
a r
m
,
w
s t i
a
s
o h
t r
e b
p e
n a
FIG. 2-04
t i a
a
l t
a e
t s
20 minute before
indi-
d
t
e h
Advertisement
Table of Contents
Troubleshooting
