Table of Contents
Advertisement
TECHNICAL GUIDE
SUNLINE PLUS™
AIR-COOLED
AIR CONDITIONERS
D1EG/D1EE036, 048, & 060
3, 4, AND 5 NOMINAL TONS
11 - 11.5 SEER
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
®
FLEXIBLE EASY TO INSTALL SINGLE
PACKAGE UNITS.
GENERAL
YORK Model DEE/DEG units are single package air condi-
tioners designed for outdoor installation on a rooftop or a
slab. These units can be equipped with field installed elec-
tric heaters for cooling/heating applications or factory
installed gas heat. The units are completely assembled on
rigid, permanently attached base rails. All piping, refriger-
ant charge, and electrical wiring is factory installed and
tested. The units require only electric power and duct con-
nections at the point of installation.
FEATURING
•
COMMON FOOTPRINT / COMMON CABINET
•
HIGH EFFICIENCY
•
CONVERTIBLE AIRFLOW DESIGN
•
OPTIONAL MOTORIZED AIR DAMPER
•
OPTIONAL MANUAL OUTDOOR DAMPER
•
FLEXIBLE INDOOR AIRFLOWS
•
FULL PERIMETER BASE RAILS
•
INSTALLER FRIENDLY CONTROL CIRCUIT
•
EASY UTILITY CONNECTIONS
•
1" OR 2" FILTERS WITH NO MODIFICATIONS
•
DIRECT DRIVE
•
OPTIONAL BELT DRIVE
•
1 YEAR LIMITED WARRANTY
•
COMPRESSORS 5 YEAR WARRANTY
•
10 YEAR LIMITED WARRANTY ON GAS-FIRED
HEAT EXCHANGERS
036-21411-002-A-0204
Advertisement
Table of Contents
Related Manuals for York SUNLINE PLUS D1EE036
Summary of Contents for York SUNLINE PLUS D1EE036
- Page 1 FLEXIBLE EASY TO INSTALL SINGLE PACKAGE UNITS. GENERAL YORK Model DEE/DEG units are single package air condi- tioners designed for outdoor installation on a rooftop or a slab. These units can be equipped with field installed elec- tric heaters for cooling/heating applications or factory installed gas heat.
-
Page 2: Table Of Contents
DESCRIPTION ......3 FEATURES ....... . 3 FACTORY-INSTALLED OPTIONS . -
Page 3: Description
036-21411-002-A-0204 DESCRIPTION YORK Sunline Plus™ units are high efficiency, convertible, single package air conditioners with a common cabinet and a common roof curb for the 3, 4 and 5 ton sizes. The units were designed for light commercial and commercial applications. -
Page 4: Factory-Installed Options
voltage terminal strip. An additional set of pin connectors is also provided to simplify the field interface of external con- trols. Mate--n--lock plug connectors are used where line and low voltage wires pass through internal bulkheads. This allows for easier troubleshooting and component replace- ment. - Page 5 036-21411-002-A-0204 PROPANE CONVERSION KIT - Converts a gas-fired heater from natural gas to propane. It contains main burner orifices, a pilot orifice and a regulator spring. LOW NOx KIT (natural gas furnaces only) - Contains five stainless steel expanded metal sheets for mounting into the heat exchanger tubes to meet the California low nitrous oxide emission requirements.
-
Page 6: Capacity Ratings - Cooling / Electric
TABLE 1: CAPACITY RATINGS - COOLING / ELECTRIC HEATING COOLING CAPACITY 80 / 67-95°F MODEL DEE036 42.5 DEE048 49.5 DEE060 58.5 Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240. Heaters are available as accessories - all with single point power supply Rated in accordance with ARI Standard 270. -
Page 7: Physical Data - Basic Unit
036-21411-002-A-0204 TABLE 4: PHYSICAL DATA - BASIC UNIT MODELS Centrifugal Blower (Dia. x Wd. in.) EVAPORATOR Fan Motor HP (Direct - Drive) BLOWER Fan Motor HP (Belt - Drive) Rows Deep EVAPORATOR Fins Per Inch COIL Face Area (Sq. Ft.) Propeller Dia. -
Page 8: Cooling Capacities - 3 Ton (Dee / Deg036)
TABLE 5: COOLING CAPACITIES - 3 TON (DEE / DEG036) AIR ON EVAPORATOR COIL TOTAL POWER CAP. INPUT °F 1500 1350 1200 1050 AIR ON EVAPORATOR COIL TOTAL POWER INPUT °F 1500 1350 1200 1050 These capacities are gross ratings. For net capacity, determine the kW of the supply air blower motor from Table 8 or 11, multiply this value by 3.425 MBH/kW to determine the motor heat, and deduct this heat from the gross capacity of the unit. -
Page 9: Cooling Capacities - 4 Ton (Dee / Deg048)
036-21411-002-A-0204 TABLE 6: COOLING CAPACITIES - 4 TON (DEE / DEG048) AIR ON EVAPORATOR COIL TOTAL POWER CAP. INPUT °F 2000 1800 1600 1400 1200 AIR ON EVAPORATOR COIL TOTAL POWER INPUT °F 2000 1800 1600 1400 1200 These capacities are gross ratings. For net capacity, determine the kW of the supply air blower motor from Table 9 or 11, multiply this value by 3.425 MBH/kW to determine the motor heat, and deduct this heat from the gross capacity of the unit. -
Page 10: Cooling Capacities - 5 Ton (Dee / Deg060)
TABLE 7: COOLING CAPACITIES - 5 TON (DEE / DEG060) AIR ON EVAPORATOR COIL TOTAL POWER CAP. INPUT °F 2500 2250 2000 1750 1500 AIR ON EVAPORATOR COIL TOTAL POWER INPUT °F 2500 2250 2000 1750 1500 These capacities are gross ratings. For net capacity, determine the kW of the supply air blower motor from Table 10 or 11, multiply this value by 3.425 MBH/kW to determine the motor heat, and deduct this heat from the gross capacity of the unit. -
Page 11: Supply Air Blower Performance -Dee
036-21411-002-A-0204 TABLE 8: SUPPLY AIR BLOWER PERFORMANCE -DEE/DEG036 W/ BELT DRIVE & SIDE DUCT MODEL FLOW 0.20 DEE/DEG WATTS 2000 1900 1800 1700 1600 1500 1400 1300 1200 MODEL FLOW 0.90 DEE/DEG WATTS 2000 1103 1270 1900 1085 1210 1800 1064 1145 1102... -
Page 12: Supply Air Blower Performance -Dee
TABLE 9: SUPPLY AIR BLOWER PERFORMANCE -DEE/DEG048 W/ BELT DRIVE & SIDE DUCT MODEL FLOW 0.20 DEE/DEG WATTS 2000 1900 1800 1700 1600 1500 1400 1300 1200 MODEL FLOW 0.90 DEE/DEG WATTS 2000 1103 1270 1900 1085 1210 1800 1064 1145 1102 1700... -
Page 13: Supply Air Blower Performance -Dee
036-21411-002-A-0204 TABLE 10: SUPPLY AIR BLOWER PERFORMANCE -DEE/DEG060 W/ BELT DRIVE & SIDE DUCT MODEL FLOW 0.20 DEE/DEG WATTS 2500 1059 1560 1077 2400 1032 1405 1054 2300 1005 1260 1024 2200 1160 1002 2100 1060 2000 1900 1800 1700 1600 1500 MODEL... -
Page 14: Supply Air Blower Performance - Dee
TABLE 11: SUPPLY AIR BLOWER PERFORMANCE - DEE/DEG036-060 W/ DIRECT DRIVE MODEL MOTOR 0.20 DEE/DEG SPEED WATTS 1684 1487 1996 1804 1681 2400 1155 2290 1105 2150 1020 MODEL MOTOR DEE/DEG SPEED WATTS 1570 1410 1315 1722 1589 1490 2096 1010 1990 1905... -
Page 15: Motor And Drive Data - Belt-Drive Blower
036-21411-002-A-0204 TABLE 13: MOTOR AND DRIVE DATA - BELT-DRIVE BLOWER BLOWER MODEL RANGE DEE / DEG 036 780 - 1120 1-1/2 1725 DEE / DEG 048 790 - 1120 1-1/2 1725 DEE / DEG 060 850 - 1220 1-1/2 1725 All motors have a solid base and are inherently protected. -
Page 16: Basic Unit W/ Belt-Drive Electrical Data
TABLE 15: BASIC UNIT W/ BELT-DRIVE ELECTRICAL DATA VOLTAGE MODEL LIMITATIONS POWER DEE/ SUPPLY 208/230-1-60 208/230-3-60 460-3-60 575-3-60 208/230-1-60 208/230-3-60 460-3-60 575-3-60 208/230-1-60 208/230-3-60 460-3-60 575-3-60 Rated in accordance with ARI Standard 110, utilization range “A”. Dual element, time delay type. = DEE models only. -
Page 17: Electrical Data Cooling/Electric Heat W/ Direct Drive Dee036
036-21411-002-A-0204 TABLE 16: ELECTRICAL DATA COOLING/ELECTRIC HEAT W/ DIRECT DRIVE DEE036 HEATER MODEL POWER ACCESSORY SUPPLY MODEL NUMBER 2CE04500506 2CE04500706 208-1-60 2CE04501006 2CE04501506 2CE04502006 2CE04500506 2CE04500706 230-1-60 2CE04501006 2CE04501506 2CE04502006 2CE04500525 2CE04500725 208-3-60 2CE04501025 2CE04501525 2CE04502025 2CE04500525 2CE04500725 230-3-60 2CE04501025 2CE04501525 2CE04502025 2CE04500746... -
Page 18: Electrical Data Cooling/Electric Heat W/ Direct Drive Dee048
TABLE 17: ELECTRICAL DATA COOLING/ELECTRIC HEAT W/ DIRECT DRIVE DEE048 HEATER MODEL POWER ACCESSORY SUPPLY MODEL NUMBER 2CE04500506 2CE04500706 208-1-60 2CE04501006 2CE04501506 2CE04502006 2CE04500506 2CE04500706 230-1-60 2CE04501006 2CE04501506 2CE04502006 2CE04500525 2CE04500725 208-3-60 2CE04501025 2CE04501525 2CE04502025 2CE04500525 2CE04500725 230-3-60 2CE04501025 2CE04501525 2CE04502025 2CE04500746 2CE04501046... -
Page 19: Electrical Data Cooling/Electric Heat W/ Direct Drive Dee060
036-21411-002-A-0204 TABLE 20: ELECTRICAL DATA COOLING/ELECTRIC HEAT W/ DIRECT DRIVE DEE060 HEATER MODEL POWER ACCESSORY SUPPLY MODEL NUMBER 2CE04500506 2CE04500706 2CE04501006 208-1-60 2CE04501506 2CE04502006 2CE04503006 2CE04500506 2CE04500706 2CE04501006 230-1-60 2CE04501506 2CE04502006 2CE04503006 2CE04500525 2CE04500725 2CE04501025 208-3-60 2CE04501525 2CE04502025 2CE04503025 2CE04500525 2CE04500725 2CE04501025 230-3-60... -
Page 20: Electrical Data Cooling/Electric Heat W/ Belt Drive Dee036 & 048
TABLE 21: ELECTRICAL DATA COOLING/ELECTRIC HEAT W/ BELT DRIVE DEE036 & 048 HEATER MODEL POWER ACCESSORY SUPPLY MODEL NUMBER 2CE04500506 2CE04500706 208-1-60 2CE04501006 2CE04501506 2CE04502006 2CE04500506 2CE04500706 230-1-60 2CE04501006 2CE04501506 2CE04502006 2CE04500525 2CE04500725 208-3-60 2CE04501025 2CE04501525 2CE04502025 2CE04500525 2CE04500725 230-3-60 2CE04501025 2CE04501525 2CE04502025... -
Page 21: Electrical Data Cooling/Electric Heat W/ Belt Drive Dee060
036-21411-002-A-0204 TABLE 22: ELECTRICAL DATA COOLING/ELECTRIC HEAT W/ BELT DRIVE DEE060 HEATER MODEL POWER ACCESSORY SUPPLY MODEL NUMBER 2CE04500525 2CE04500725 2CE04501025 208-1-60 2CE04501525 2CE04502025 2CE04503025 2CE04500525 2CE04500725 2CE04501025 230-1-60 2CE04501525 2CE04502025 2CE04503025 2CE04500525 2CE04500725 2CE04501025 208-3-60 2CE04501525 2CE04502025 2CE04503025 2CE04500525 2CE04500725 2CE04501025 230-3-60... -
Page 22: Power Supply, Power Wiring Three Phase
REFER TO THE ELECTRI- CAL DATA TABLES TO SIZE THE DISCONNECT SWITCH, OVERCURRENT PROTECTION AND WIRING FIGURE 2 - POWER SUPPLY, POWER WIRING SINGLE PHASE FIGURE 3 - POWER SUPPLY, POWER WIRING THREE PHASE COOLING ONLY (24 VOLT THERMOSTAT) THERMOSTAT UNIT TERMINAL TERMINALS STRIP TB1... -
Page 23: Control Wiring - Cooling/Heating
036-21411-002-A-0204 C O O L I N G / H E A T I N G ( E L E C T R O N I C T H E R M O S T A T ) A D D J U M P E R E L E C T R O N I C P R O G R A M M A B L E T H E R M O S T A T 2 E T 0 7 7 0 1 0 2 4 ( I N C L U D E S S U B B A S E ) . -
Page 24: Unit Dimensions Dee 3, 4, & 5 Ton
DEE UNITS 3-5 TON FIGURE 9 - UNIT DIMENSIONS DEE 3, 4, & 5 TON TABLE 23: UTILITIES ENTRY DATA KNOCKOUT HOLE SIZE (DIA.) 7/8” 2” 1-5/8” 1-1/2” Knockouts in the bottom of the unit can be located by the slice in the insulation. DO NOT remove the 2”... -
Page 25: Unit Dimensions Deg 3, 4, & 5 Ton
036-21411-002-A-0204 DEG UNITS 3-5 TON FIGURE 11 -UNIT DIMENSIONS DEG 3, 4, & 5 TON TABLE 24: DEE/DEG UNIT CLEARANCES DEE UNITS FRONT DEG UNITS BACK LEFT SIDE (Filter Access) RIGHT SIDE (Cond. Coil) BELOW UNIT ABOVE UNIT Units may be installed on combustible floors made from wood or class A, B, or C roof covering material. - Page 26 FIGURE 12 -DEE/DEG DIMENSIONS REAR VIEW - 3, 4, & 5 TON Duct covers - units are shipped with all air duct openings covered. For side duct applications: • Remove and discard the supply and return air duct covers. • Connect ductwork to duct flanges on the rear of the unit.
- Page 27 036-21411-002-A-0204 FIGURE 13 -DETAIL B UNIT DIMENSIONS WITH DAMPER/RAINHOOD FIGURE 14 -UNIT & CURB APPLICATION Unitary Products Group...
-
Page 28: Accessory's Weight
FIGURE 15 -ROOF CURB DIMENSIONS DEE & DEG 3, 4, & 5 TON TABLE 25: UNIT WEIGHTS CORNER WEIGHTS UNIT UNIT WEIGHT (lbs.) “A” DEG036 DEG048 DEG060 DEE036 DEG048 DEG060 FIGURE 16 -CENTER OF GRAVITY TABLE 26: ACCESSORY’S WEIGHT (location, lbs.) “B”... - Page 29 036-21411-002-A-0204 FIGURE 17 -TYPICAL APPLICATIONS FIGURE 18 -TYPICAL ROOF TOP INSTALLATION Unitary Products Group OOF JACK INSTALLATION OOF CU B INSTALLATION SLAB ON G OUND INSTALLATION...
-
Page 30: Mechanical Specifications
MECHANICAL SPECIFICATIONS GENERAL DESCRIPTION Units shall be High Efficiency factory-assembled, single pack- aged, (DUS Electric Cooling/Gas Heat, DHC Electric Cooling/ Optional Electric Heat), designed for outdoor mounted instal- lation. Units shall have minimum SEER ratings of 11.0. They shall have built in field convertible duct connections for down discharge supply/return or horizontal discharge supply/return, and be available with factory installed options or field installed accessories. - Page 31 036-21411-002-A-0204 Balance-port thermostatic expansion valve with independent circuit feed system. Filter drier/strainer to eliminate any moisture or for- eign matter. Accessible service gage connections on both suc- tion and discharge lines to charge, evacuate, and measure refrigerant pressure during any necessary servicing or troubleshooting, without losing charge.
- Page 32 14. ELECTRIC HEAT - Slide-in design, provides single point power and ranges from 5 to 30 KW. OTHER FACTORY INSTALLED OPTIONS HIGH PERFORMANCE BELT DRIVE MOTOR TECHNICOAT PHENOLIC COATED COND. COIL ELECTRONIC ENTHALPY ECONOMIZER DUAL INPUT ELECTRONIC ENTHALPY ECONO- MIZER Supersedes: 036-21411-001-A-0502 5005 York Drive 036-21411-002-A-0204 Norman 73069...