Installer/Configuration Menu - White Rodgers 1F83-277 User Manual

Heating & air conditioning non-programmable, auto changeover, multi-stage/heat pump thermostat

Hide thumbs Also See for 1F83-277:

Specifications (2 pages)

Installation instructions manual (13 pages)

Table Of Contents

Table of Contents

CONFIGURATION MENU

Press the System button until OFF

Press

Step

Button(s)

(Factory Default)

Step

Button(s)

(Factory Default)

System

(Room Temperature)

System

4) Select Backlight Display

Select Backlight Display

Select Backlight Display – The display backlight improves

Select Backlight Display

display contrast in low lighting conditions. When the "C"

terminal is powered, selecting backlight CdL ON will keep

the light on continuously. Select backlight OFF will keep

the light on momentarily after any key is pressed. When the

"C" terminal is not powered, the light will be on momentarily

after any key is pressed no matter the backlight is selected

ON or OFF.

5) Select (Fast) Second Stage ON or OFF

Select (Fast) Second Stage ON or OFF – In the run mode,

Select (Fast) Second Stage ON or OFF

if the setpoint temperature is manually raised by 3°F (2°C)

or more above the actual temperature with the

fast second stage feature is enabled, FA ON, the second

stage will energize immediately. With FA OFF, second

stage will not energize until the setpoint temperature is 1°F

or more above actual temperature for more than ten min-

utes.

Select filter replacement run time

6) Select filter replacement run time

Select filter replacement run time – The thermostat will

Select filter replacement run time

display FLTR

FLTR

FLTR after a set time of operation. This is a remind-

FLTR

er to change or clean your air filter. This time can be set from

0 to 1950 hours in 50 hour increments. A selection of 000

will cancel this feature

will cancel this feature. When FLTR

HOLD

clear it by pressing HOLD

HOLD and RUN

HOLD

resets the timer and starts counting the hours until the next

filter change. Contact your system manufacturer for a

specific replacement/maintenance interval.

OFF

OFF is displayed, then press the

OFF

INSTALLER/CONFIGURATION MENU

Displayed

Press

Displayed

Press

to select

MS 2

SS1, HP2, HP1

MS 2

SS1, HP2, HP1

F A

(OFF)

CDL

(ON)

F A

(ON)

0 FLTR

50-1950

50-1950 (increments of 50)

50-1950

0°F

4 LO to 4 HI

° F

LR 62 to LR89

(90)

LR 46 to LR 82

(45)

C A

(OFF)

0 0 0 0 0

001 to 999

, and the

A selection of 000

FLTR

FLTR is displayed, you can

FLTR

RUN

RUN at the same time. This

RUN

or or or or or

Selects Single stage, Multi-stage, or Heat Pump

(Single stage or 2-stage) System Configuration

Selects Compressor Lockout CL OFF

(ON)

CDL

(OFF)

F A

(OFF)

Selects Temperature Display Adjustment 4 LO

°C

C A

(ON)

Selects Keypad lockout combination number

Select Temperature Display Adjustment 4 LO to 4 HI

7) Select Temperature Display Adjustment 4 LO to 4 HI

Select Temperature Display Adjustment 4 LO to 4 HI –

Select Temperature Display Adjustment 4 LO to 4 HI

Allows you to adjust the room temperature display up to 4°

higher or lower. Your thermostat was accurately calibrated

at the factory but you have the option to change the display

temperature to match your previous thermostat. The cur-

rent or adjusted room temperature will be displayed on the

left side of the display.

Select F° or C° Readout

8) Select F° or C° Readout

Select F° or C° Readout

Select F° or C° Readout – Changes the display readout

to Centigrade or Fahrenheit as required.

Limited Heat Range

9) Limited Heat Range

Limited Heat Range

Limited Heat Range – This feature provides a maximum

setpoint temperature for heat. The default setting is 90°F. It

can be changed between 62°F and 89°F by pressing the

temperature up

temperature up or temperature down

temperature up

10) Limited Cool Range

Limited Cool Range

Limited Cool Range – This feature provides a minimum

Limited Cool Range

setpoint temperature for cool. The default setting is 45°F. It

can be changed between 46°F and 82°F by pressing the

temperature up or temperature down key.

11) This feature not available

This feature not available

This feature not available.

This feature not available

and

simultaneously

Comments

Selects Fast or Slow Cycle Selection

CL OFF

CL OFF or ON

Selects Backlight Display

Selects Fast Second Stage ON

ON or OFF

Selects filter replacement run time

For °C

°C selection

°C

Selects Limited HEAT

HEAT

HEAT range

HEAT

Selects Limited COOL range

Feature Not Available

Selects Keypad Lockout

Press System to set code

Returns to the OFF position

temperature down

temperature down key.

temperature down

OFF

4 LO to 4 HI

4 LO

4 HI

Table of Contents

Show Quick Links

Hide quick links:

Table of Contents

This manual is also suitable for:

Part no. 37-6509a

Installer/Configuration Menu - White Rodgers 1F83-277 User Manual

INSTALLER/CONFIGURATION MENU

Hide quick links:

Related Manuals for White Rodgers 1F83-277

Related Content for White Rodgers 1F83-277

This manual is also suitable for:

Table of Contents