Troubleshooting; Ddr Sdram - Intel D865PCD Quick Reference

Troubleshooting

problemi Résolution de problèmes Fehlerbehebung
problemas Resolución de problemas
Desktop Board D865PCD system fails to boot.
•
Ensure that the power supply cable with the 2x2-pin connector is
plugged into the 12 V processor core voltage connector located
near the processor socket on the desktop board.
•
Remove and re-insert the Intel Pentium 4 processor, memory, and
any add-in cards to make sure they are fully seated. Remove any
non-essential hardware components and boot the system.
•
Disconnect all power and remove the CMOS battery. Wait 10
minutes, then re-install the battery, reconnect power, and boot the
system.
A repeating beep error code is heard and the desktop board does
not boot or show any video.
This beep code may indicate a problem during detection of the DDR
SDRAM memory device. Check to ensure that system memory is
properly installed and that the DIMMs meet the Memory Module
Requirements listed in the Supported Components section of the
Product Guide.
D865PCD
•
2x2
12 V
•
Intel Pentium 4
•

DDR SDRAM

D865PCD
•
2x2
•
Intel Pentium 4
,
.
•
10 ,
,
DDR SDRAM
'
Intel Desktop Board D865PCD Quick Reference
CMOS 10
12 V
.
,
CMOS
,
.
.
.
, DIMM '
5R]ZL ]\ZDQLH SUREOHPyZ WHFKQLF]Q\FK Risoluzione dei
•
2x2
•
Intel Pentium 4
•
6\VWHP Sá\W\ JáyZQHM '3&' QLH XUXFKDPLD VL 
• 6SUDZG  F]\ NDEHO ]DVLODM F\ ]H ]á F]HP ] [ Z\SURZDG]HQLDPL
]RVWDá SRGá F]RQ\ GR ]á F]D SRGVWDZRZHJR QDSL FLD SURFHVRUD
12 9 ]QDMGXM FHJR VL Z SREOL X JQLD]GD SURFHVRUD QD Sá\FLH
JáyZQHM
• :\MPLM L SRQRZQLH Záy SURFHVRU ,QWHO 3HQWLXP  SDPL ü L
ZV]\VWNLH NDUW\ UR]V]HU]HQLD DE\ XSHZQLü VL  H ]RVWDá\ VWDELOQLH
zainstalowane. 2Gá F] ZV]\VWNLH PQLHM LVWRWQH VNáDGQLNL VSU] WX L
uruchom system.
• 2Gá F] ZV]\VWNLH XNáDG\ ]DVLODQLD L Z\MPLM EDWHUL SDPL FL
DIMM
&026 2GF]HNDM  PLQXW D QDVW SQLH SRQRZQLH ]DLQVWDOXM
EDWHUL  SRGá F] ]DVLODQLH L XUXFKRP V\VWHP
6á\V]DOQ\ MHVW SRZWDU]DOQ\ V\JQDá G ZL NRZ\ Eá GX L QLH PR QD
XUXFKRPLü Sá\W\ JáyZQHM D QD HNUDQLH QLH MHVW Z\ ZLHWODQ\ DGHQ
.
obraz.
6\JQDá G ZL NRZ\ Eá GX PR H ZVND]\ZDü QD SUREOHP SRGF]DV
Z\NU\ZDQLD XU] G]HQLD SDPL FL ''5 6'5$0 6SUDZG  F]\ SDPL ü
V\VWHPRZD ]RVWDáD SUDZLGáRZR ]DLQVWDORZDQD RUD] F]\ PRGXá\ SDPL FL
',00 VSHáQLDM Z\PDJDQLD RNUH ORQH Z UR]G]LDOH 2EVáXJLZDQH
skáDGQLNL w ,QVWUXNFML Sá\W\ JáyZQHM.
.
Il sistema della Desktop Board D865PCD non si avvia.
.
•
Accertarsi che il cavo di alimentazione con il connettore a 2x2 pin
sia collegato al connettore dell'alimentazione principale a 12 V del
processore posizionato sulla scheda.
•
Rimuovere e inserire di nuovo il processore Intel Pentium 4, la
memoria e tutte le schede aggiuntive per accertarsi che siano
inserite correttamente. Rimuovere tutti i componenti hardware non
fondamentali e avviare il sistema.
•
Scollegare l'alimentazione e rimuovere la batteria CMOS.
Attendere 10 minuti, quindi installare di nuovo la batteria,
.
ricollegare l'alimentazione e avviare il sistema.
D865PCD
12 V
CMOS
10
DDR SDRAM
DIMM
Solução de
15