Important Safety Information - Hatco GLO-RAY GRAM Series Installation And Operating Manual

English
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
WARNING
ELECTRIC SHOCK HAzARD:
• Units require a hardwired connection to on-site
electrical system. Connection must be properly
grounded and of
configuration for electrical specifications of unit.
Contact a qualified electrician to determine and perform
proper electrical connection.
• Turn OFF power switch, turn off power at circuit
breaker, and allow unit to cool before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAzARD: Do not install Max Watt strip heaters above
or around combustible surfaces. Discoloration or
combustion could occur. Max Watt strip heaters must be
installed in non-combustible surroundings only.
ExPLOSION HAzARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
Use only light bulbs that meet or exceed (National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
Make sure food product has been heated to the proper
food-safe temperature. Failure to heat food product
properly may result in serious health risks. This unit is for
pre-heated food product only.
Form No. GRamm-1114
correct voltage, size,

IMPORTANT SAFETY INFORMATION

For installation with chains, make sure the chains have
sufficient strength and are securely fastened to both the
unit and the mounting location. Poorly installed chains
and may cause the unit to loosen and fall. Do not place
anything on top of units installed with chains.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
BURN HAzARD: Some exterior surfaces on the unit will get
hot. Use caution when touching these areas.
Standard and approved manufacturing oils may smoke up
to 30 minutes during initial startup. This is a temporary
condition. Operate unit without food product until smoke
dissipates.
Strip heaters equipped with incandescent lights that
require a circuit breaker larger than 20 amps for the heat
element must have a separate circuit breaker for the
incandescent lights that is 20 amps or less.
To ensure safe and proper operation, refer to the Clearance
Requirements listed in the Installation section of this
manual.
Installation of two or more separate units with less than
3" (76 mm) between housings may result in premature
failure of component parts. Failure to provide proper
spacing may result in heat damage to electrical
components and will void warranty.
Units are voltage-specific. Refer to specification label for
electrical requirements before beginning installation.
Do not add a decorative soffit to hide a pass-through
mounted strip heater. Excessive heat can cause unit
failure.
To prevent premature failure of components due to
excessive heat, remote mounted control enclosures must
be installed outside the strip heater heat zone.
Damage to any countertop material caused by heat
generated from Hatco equipment is not covered under the
Hatco warranty. Contact the manufacturer of the
countertop material for application information.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
3
WARNING
CAUTION
NOTICE