Important Safety Information - Hatco Glo-Ray GRAIH Series Installation And Operating Manual

English English
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
WARNING
ELECTRIC SHOCK HAZARD:
• Units supplied without an electrical cord and plug
require a hardwired connection to the on-site electrical
system. Connection must be properly grounded and
of the correct voltage, size, and configuration for the
electrical specifications of the unit. Contact a qualified
electrician to determine and install the proper electrical
connection.
• Turn power OFF at fused disconnect switch/circuit
breaker and allow unit to cool before performing any
maintenance, adjustments, or cleaning.
• For hardwired units, all electrical connections must be
in accordance with local electrical codes and any other
applicable codes. Connections should be made by a
qualified, licensed electrician.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 21°C (70°F).
• Do not clean unit when it is energized or hot.
• Do not steam clean or use excessive water on the unit.
• This unit is not "jet-proof" construction. Do not use
jet-clean spray to clean this unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD:
• Do not install unit above or around combustible
surfaces. Discoloration or combustion could occur.
Unit must be installed in non-combustible surroundings
only.
• Do not store or use gasoline or other flammable vapors
or liquids in the vicinity of this or any other appliance.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
414-671-6350.
Form No. GRAIH_AAM-0117

IMPORTANT SAFETY INFORMATION

Make sure food product has been heated to the proper food-
safe temperature before placing in unit. Failure to heat food
product properly may result in serious health risks. This
unit is for holding preheated food product only.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure that food product is held and served at a
safe temperature.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
Standard and approved manufacturing oils may smoke up
to 30 minutes during initial startup. This is a temporary
condition. Operate unit without food product until smoke
dissipates.
Light-equipped strip heaters that require a circuit breaker
20 amps or larger must be installed with a remote control
enclosure containing a fuse rated at 20 amps or less for
the light circuit.
Ensure safe and proper operation. Refer to the "Minimum
Clearance Requirements" listed in the Installation section
of this manual.
Damage to countertop material such as Corian® and similar
products caused by heat generated from Hatco equipment
is not covered under the Hatco warranty. Contact the
manufacturer of the countertop material for application
information.
Remote mounted control boxes must be installed outside
strip heater heat zone to prevent premature failure of
components due to excessive heat.
Installation of two or more separate units with less than
76 mm (3"( between housings may result in premature
failure of component parts. Failure to provide proper
spacing may result in heat damage to electrical components
and are not covered by warranty.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
3
WARNING
CAUTION
NOTICE